Abstract:The construction of a tunnel portal faces the challenges of complex geological conditions, such as shallow burial and asymmetrical loading. In addition, the adverse effects of factors such as the layout form of the tunnel must also be considered. Thus, the construction of portals has always been the focus of tunnel engineering. Under the coupling of multiple adverse factors, such as complex geological conditions and special layout form, the tunnel portal is prone to excessive deformation, supporting structural cracking, and even collapse during excavation. In this study, a shallow buried and asymmetrically loaded tunnel with a small clear-distance in northwest China was considered as an engineering case. To address the distresses of slope instability, peeling off and block falling of primary support concrete, and cracking of secondary lining concrete in the tunnel portal construction, combined with field investigations, statistical analysis, numerical simulation, and deformation monitoring, the failure mechanism of supporting structures was deeply studied and corresponding treatment measures were proposed. The research results indicated that loose and broken gravel soil in the shallow buried section, asymmetrical loading, surface water infiltration, and short construction spacing between the two tunnels were the main triggers of supporting structures failure. Affected by topographic bias, the loose load generated by the surrounding rock on the deeply buried side squeezed the entire tunnel to the shallow buried side after portal excavation. This deformation trend became more significant after the gravel soil deteriorated by water immersion. The retaining wall produced a clockwise rotation deformation around the wall corner in the process of limiting the tunnel deviation, and the local wall body cracked owing to excessive tensile stress. The primary support concrete and secondary lining concrete produced excessive asymmetrical deformation because of significant asymmetrical loading. Concrete with excessive deformation was cracked by obvious tensile or shear stresses. The subsequent tunnel excavation had a significant negative impact on the stability of the prior tunnel. Combining the failure mechanism of the supporting structures and the characteristics of the continuous development of cracks, the treatment measures of ‘stabilize the stratum first and then treat the cracks’ were proposed, including the backfilling and tamping the shallow buried side at tunnel portal, reinforcing the interlaid rock by ground surface grouting, setting intercepting ditch at the slope top, and staggering a certain safe excavation distance between the following tunnel and the prior tunnel. Field monitoring and patrol inspection results indicated that the proposed treatment measures achieved the expected results. The research results can provide corresponding construction experience and suggestions for similar projects in future.

Grouting Reinforcement of Shallow and Small Clearance Tunnel

Model test study of the face stability of the shallow tunnel in the clay

Effect of Grouting Reinforcement on Settlement of Existing Tunnels: Case Study of a New Crossing Underpass

Earth Pressure and Internal Forces of Tunnel Lining in Jet Grouting Reinforced Mud Stratum

Failure mechanism and treatment measures of supporting structures at the portal for a shallow buried and asymmetrically loaded tunnel with small clear-distance

Experiment and Numerical Simulation on Grouting Reinforcement Parameters of Ultra-Shallow Buried Double-Arch Tunnel

Method of Calculating the Compensation for Rectifying the Horizontal Displacement of Existing Tunnels by Grouting

Bridging the gap between engineering properties and grouting reinforcement mechanisms for loess in eastern China: taking Jinan loess as an example

Study on Sensitivity Parameters Analysis of Grouting Reinforcement Underpassing Existing Subway Tunnel by Numerical Modeling

Method of Calculating the Vertical Displacement and Additional Stress of Existing Tunnels under the Influence of Grouting Rings of New Tunnels

Theoretical analysis on horizontal rectification of tunnel near deep foundation pit by grouting

Numerical Simulation of Effect of Foundation Pit Excavation on Underlain Shield Tunnel

Experimental investigation on the reinforcement of a high-pressure jet grouting pile for an ultra-shallow tunnel in a strongly weathered stratum

Layered Grouting Technology Based on a Comprehensive Water-to-Cement Ratio for the Overlying Loess Stratum of Urban Shallow Tunnels

Advanced Grouting Model and Influencing Factors Analysis of Tunnels with High Stress and Broken Surrounding Rock

Parameters Optimization of Curtain Grouting Reinforcement Cycle in Yonglian Tunnel and Its Application

Numerical Analysis of Grouting of Water-Enriched Karst Highway Tunnel Based on Critical Water-Enriched Height

A Study on the Stability of Reinforced Tunnel Face Using Horizontal Pre-Grouting

Analytical solution to the mechanical response of grouting lifting in existing shield tunnels and engineering case verification

Mechanism of structural defects in cut-and-cover tunnels within high-fill regions and gradient pile foundation reinforcement technology

Study on the optimum grouting materials and their performance in the TBM tunnel collapse reinforcement project