Abstract:Latent heat thermal energy storage systems can regulate the intermittency of electricity generation in a grid powered by renewable energy sources. Such systems could be used in conjunction with Brayton power generation cycles operating at high temperatures (520 degrees C-750 degrees C) delivering higher efficiency. However, a trade-off of higher thermal efficiency can be higher thermal stresses. The isothermal latent heat thermal energy storage and release can reduce the thermal stresses for a specific design. This study investigates the impact of the orientation on the melting process and the consequent thermal stresses in a lab-scale latent heat shell and tube system using a combination of transient computational fluid dynamics and finite element analyses. With a high temperature phase change material melting at 705.8 degrees C, two initial temperatures of 700 degrees C and 650 degrees C were considered in transient analyses, leading to a 50 K and 100 K initial temperature difference across the tubes, respectively. For the structural analysis, an elastic method was employed for the condition of 50 K temperature difference, and an elastic-plastic analysis for the condition of 100 K to account for plastic deformation. The results of the elastic analysis presented the maximum thermal stresses of 63.5 MPa and 106.7 MPa in tubes in the horizontal and vertical orientations, respectively. The stress in the tube sheet was slightly higher (94.5 MPa) for the horizontal system compared with 90.4 MPa in the vertical position. For the condition of 100 K, the results of the elasticplastic analysis identified the highest stresses of 172.5 MPa and 147.4 MPa in the tube sheets of the horizontal and vertical systems, respectively. For both initial temperature conditions, the stress level in tubes is lower in the horizontal orientation, which is where most cost occurs in a shell and tube system. Particularly important for the 100 K condition, the results show a lower stress of 100 MPa in tubes for a horizontal system compared with 140 MPa in a vertical orientation. In general, the lowest thermal stress occurs where a melt layer forms around tubes during the early stages of a melting process. A higher stress occurred in parts in contact with argon. The highest level of stress occurred in parts in contact with solid PCM, which has direct implications for larger vessel designs. This study provides insights into hydrothermal and mechanical design of a PCM system to prevent and/ or manage localised maximum thermal stresses for a cost-effective thermal energy storage system.

Thermal Performance Assessment of a Thermal Energy Storage Tank: Effect of Aspect Ratio and Tilted Angle

Numerical Analysis of Heat Transfer Behaviours of Melting Process for Ice Thermal Storage Based on Various Heat Source Configurations

Parametric Study on Melting Process of a Shell-and-tube Latent Thermal Energy Storage under Fluctuating Thermal Conditions

Synergistic Improvement of Melting Rate and Heat Storage Capacity by a Rotation-Based Method for Shell-and-tube Latent Thermal Energy Storage

Visualizing Experimental Study of the Effect of Inclination Angle on the Melting Performance for an Energy Storage Tank

Numerical Investigation of Heat Transfer Characteristics in a Shell- And-Tube Latent Heat Thermal Energy Storage System

Study of the Effect of Tilting Lateral Surface Angle and Operating Parameters on the Performance of a Vertical Shell-and-tube Latent Heat Energy Storage System

Effect of phase change heat storage tank with gradient fin structure on solar energy storage: A numerical study

Melting assessment on the angled fin design for a novel latent heat thermal energy storage tube

Melting assessment on the effect of nonuniform Y-shaped fin upon solid–liquid phase change in a thermal storage tank

Evaluation of Variable Rotation on Enhancing Thermal Performance of Phase Change Heat Storage Tank

Experimental and Numerical Investigation on Enhancing Heat Transfer Performance of a Phase Change Thermal Storage Tank

Influence of supergravity and tilted condition on melting behavior in a thermal storage tank

Optimization of Melting Performance of a Heat Storage Tank under Rotation Conditions: Based on Taguchi Design and Response Surface Method

Thermal Performance Analysis of a Mounded Liquid Ethylene Storage Tank

Influence of Microgravity on Melting Performance of a Phase-Change Heat Storage Tank

Thermal Performance Evaluation of Combined Sensible-Latent Heat Storage Tank with a Different Storage Medium

Melting Performance Assessments on a Triplex-Tube Thermal Energy Storage System: Optimization Based on Response Surface Method with Natural Convection

Orientation Impact on Structural Integrity of a Shell and Tube Latent Heat Thermal Energy Storage System

Investigation of the Dynamic Melting Process in a Thermal Energy Storage Unit Using a Helical Coil Heat Exchanger

Investigation and Optimization on Melting Performance of a Triplex-Tube Heat Storage Tank by Rotational Mechanism