Abstract:The microstructure and corrosion resistance of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions were investigated. The composition was detected by X-ray fluorescence (XRF), and the microstructure was analyzed by optical microscopy (OM) and scanning electron microscope (SEM) equipped with energy-dispersive spectroscopy (EDS). The corrosion behavior was investigated by hydrogen evolution tests, weight loss tests and electrochemical measurements. The Mg–0.5Zn–0.2Ca–0.2Ce alloy has much better corrosion resistance compared with the commercial AZ31 sheet, which can be attributed to its dispersive second phases and protective corrosion products film on the alloy surface. Moreover, the as-rolled Mg–0.5Zn–0.2Ca–0.2Ce alloy shows much better corrosion resistance compared with the as-extruded Mg–0.5Zn–0.2Ca–0.2Ce alloy. This can be due to three aspects: The as-rolled alloy has smaller grain size; the as-rolled alloy has lower (10\({\bar{1}}\)0)/(11\({\bar{2}}\)0) texture intensity; the residual stress of the as-rolled alloy is eliminated during the annealing process, but large residual stress exists in the as-extruded alloy produced by the extrusion process.

Corrosion behavior of a Mg–Zn–Ca–La alloy in 3.5 wt% NaCl solution

Corrosion Behavior of Mg-Zn-Y-Zr Alloys in Nacl Solution

Effect of micro-alloying element La on corrosion behavior of Al-Mg-Si alloys

Microstructures, Mechanical Properties and Corrosion Resistances of Extruded Mg-Zn-Ca-Xce/La Alloys

High corrosion resistance and weak corrosion anisotropy of an as-rolled Mg-3Al-1Zn (in wt.%) alloy with strong crystallographic texture

Microstructure and Corrosion of Cast Magnesium Alloy ZK60 in NaCl Solution

The effects of Ca on the microstructure, mechanical and corrosion properties of extruded Mg-2Zn-0.5Mn alloy

Investigating the corrosion behavior of as‐cast Mg‐Zn‐Ca alloys with the same Zn/Ca atomic ratio by in situ observation

A Comparison Study of Ce/La and Ca Microalloying on the Bio-Corrosion Behaviors of Extruded Mg-Zn Alloys

Enhancing corrosion resistance of Mg-Al-Mn-Ca-Y dilute alloy via novel core-shell structured Al8Mn4Y-Al2Ca and controllable solute segregation

Elucidating the dependence of corrosion behavior and mechanical property on the grain structure of low-temperature as-extruded Mg–Zn–Ca–Zr alloy

The effects of Nd, La, and Ca addition on the corrosion properties of as-cast and as-rolled ZM21 Mg alloys

Microstructure, mechanical properties and corrosion behavior of extruded Mg-Zn-Ca alloys with same Zn/Ca atomic ratio

Comparative Study on Corrosion Behavior of As-Cast and Extruded Mg–5Y–7Gd–1Nd–0.5Zr Alloy in 5% NaCl Aqueous Solution

Effect of CaCl2 and NaHCO3 in Physiological Saline Solution on the Corrosion Behavior of an As-Extruded Mg–Zn–Y–Nd alloy

Microstructure and corrosion properties of Mg–0.5Zn–0.2Ca–0.2Ce alloy with different processing conditions

The Corrosion Behaviors of Mg–7Gd–5Y–1Nd–0.5Zr Alloy under (NH4)2SO4, NaCl and Ca(NO3)2 Salts Spray Condition

Investigation of Corrosion Behaviors of Mg–6Gd–3Y–0.4Zr Alloy in NaCl Aqueous Solutions

Microstructure, Mechanical Properties and Corrosion Behaviors of Al–Li–Cu–Mg–Ag–Zn Alloys

Comparative Study on Corrosion Behavior and Mechanism of As-Cast Mg–Zn–Y and Mg–Zn–Gd Alloys

Comparative study of corrosion behaviors of die cast LA42 and AZ91 alloys