Abstract:This study presents a colloidal synthesis method to produce thermoelectric Cu3SbSe4 nanocrystals with high yield. Pb doping is employed to increase carrier concentration and effective mass, confirmed by experimental studies and theoretical calculations. Additionally, lattice distortions and other intriguing nanostructures are found to significantly reduce thermal conductivity. Consequently, the thermoelectric figure of merit zT is greatly enhanced. Developing cost‐effective and high‐performance thermoelectric (TE) materials to assemble efficient TE devices presents a multitude of challenges and opportunities. Cu3SbSe4 is a promising p‐type TE material based on relatively earth abundant elements. However, the challenge lies in its poor electrical conductivity. Herein, an efficient and scalable solution‐based approach is developed to synthesize high‐quality Cu3SbSe4 nanocrystals doped with Pb at the Sb site. After ligand displacement and annealing treatments, the dried powders are consolidated into dense pellets, and their TE properties are investigated. Pb doping effectively increases the charge carrier concentration, resulting in a significant increase in electrical conductivity, while the Seebeck coefficients remain consistently high. The calculated band structure shows that Pb doping induces band convergence, thereby increasing the effective mass. Furthermore, the large ionic radius of Pb2+ results in the generation of additional point and plane defects and interphases, dramatically enhancing phonon scattering, which significantly decreases the lattice thermal conductivity at high temperatures. Overall, a maximum figure of merit (zTmax) ≈ 0.85 at 653 K is obtained in Cu3Sb0.97Pb0.03Se4. This represents a 1.6‐fold increase compared to the undoped sample and exceeds most doped Cu3SbSe4‐based materials produced by solid‐state, demonstrating advantages of versatility and cost‐effectiveness using a solution‐based technology.

Optimal Performance of Cu 1.8 S 1− X Te X Thermoelectric Materials Fabricated Via High-Pressure Process at Room Temperature

Optimal performance of Cu1.8S1−xTex thermoelectric materials fabricated via high-pressure process at room temperature

Are Cu2Te‐Based Compounds Excellent Thermoelectric Materials?

High Thermoelectric Figure of Merit Achieved in Cu2S1-xTex Alloys Synthesized by Mechanical Alloying and Spark Plasma Sintering

Facile Surfactant-Free Microwave-Assisted Solvothermal Synthesis of Cu2Te1−S with Enhanced Thermoelectric Performance

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu1.8S Via Carrier Concentration Regulation and Multiscale Phonon Scattering

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

Enhanced thermoelectric properties of Mn Cu1.8S via tuning band structure and scattering multiscale phonons

Realizing high thermoelectric performance in Te nanocomposite through Sb2Te3 incorporation

Modulation Doping of P-Type Cu12Sb4S13 Toward Improving Thermoelectric Performance

Multiple Nanostructures in High Performance Cu2S0.5Te0.5 Thermoelectric Materials

Thermoelectric Cu-doped (Bi,sb)(2)te-3: Performance Enhancement and Stability Against High Electric Current Pulse

Enhanced Thermoelectric Performance of p-type AgSbTe2 via Cu Doping

Thermoelectric Performance of Surface-Engineered Cu 1.5- x Te-Cu 2 Se Nanocomposites

High Thermoelectric Performance of SnTe Via in Doping and Cu1.75Se Nanostructuring Approach

Realizing High Thermoelectric Performance in Cu2Te Alloyed Cu1.15In2.29Te4

Optimized Thermoelectric Properties of Bi0.48Sb1.52Te3 Through AgCuTe Doping for Low-Grade Heat Harvesting.

Band Engineering Through Pb‐Doping of Nanocrystal Building Blocks to Enhance Thermoelectric Performance in Cu3SbSe4

Effects of sintering temperature on thermoelectric properties of Cu1.8S bulk materials

Sb2Te3 based alloy with high thermoelectric and mechanical performance for low-temperature energy harvesting