Abstract:The use of joints fabricated from dissimilar titanium alloys allows the design of structures with local properties tailored to different service requirements. To develop welded structures for aerospace applications, particularly under critical loading, an understanding of the fatigue behavior is crucial, but remains limited, especially for solid-state technologies such as linear friction welding (LFW). This paper presents the fatigue behavior of dissimilar titanium alloys, Ti-6Al-4V (Ti64) and Ti-6Al-2Sn-4Zr-2Mo-0.1Si (Ti6242), joined by LFW with the aim of characterizing the stress versus number of cycles to failure (S-N) curves in both the low- and high-cycle fatigue regimes. Prior to fatigue testing, metallurgical characterization of the dissimilar alloy welds indicated softening in the heat-affected zone due to the retention of metastable β, and the typical practice of stress relief annealing (SRA) for alleviating the residual stresses was effective also in transforming the metastable β to equilibrated levels of α + β phases and recovering the hardness. Thus, the dissimilar alloy joints were fatigue-tested in the SRA (750 °C for 2 h) condition and their low- and high-cycle fatigue behaviors were compared to those of the Ti64 and Ti6242 base metals (BMs). The low-cycle fatigue (LCF) behavior of the dissimilar Ti6242-Ti64 linear friction welds was characterized by relatively high maximum stress values (~ 900 to 1100 MPa) and, in the high-cycle fatigue (HCF) regime, the fatigue limit of 450 MPa at 107 cycles was just slightly higher than that of the Ti6242 BM (434 MPa) and the Ti64 BM (445 MPa). Fatigue failure of the dissimilar titanium alloy welds in the low-cycle and high-cycle regimes occurred, respectively, on the Ti64 and Ti6242 sides, roughly 3 ± 1 mm away from the weld center, and the transitioning was reasoned based on the microstructural characteristics of the BMs.

Low-Cycle Fatigue Properties of Ti6Al4V Laser-Welded Joints Based on a Local Strain Approach

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

A Study of the Back Stress and the Friction Stress Behaviors of Ti-6Al-4V Alloy During Low Cycle Fatigue at Room Temperature

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Low Cycle Fatigue Properties of a 9–12% Cr Martensitic Steel Welded Joint with Ni-based Weld Metal Based on a Local Strain Approach

Effect of Laser Heat Input on the Microstructures and Low-Cycle Fatigue Properties of Ti60 Laser Welded Joints

Microstructure and Mechanical Properties of Laser Welded Lap Joints of Ti-6Al-4V Alloy

Low-cycle fatigue in ultra-high-strength steel welded joints in the as-welded and post-weld-treated conditions

Microstructure and pore sensitivities in very high cycle fatigue behaviors of titanium alloy welded joints under stress ratios

High‐cycle and Very‐high‐cycle Fatigue Behavior at Two Stress Ratios of Ti‐6Al‐4V Manufactured Via Laser Powder Bed Fusion with Different Surface States

Fatigue Behavior of Linear Friction Welded Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo-0.1Si Dissimilar Welds

Comparison of Low-Cycle Fatigue Properties of Two Kinds of High Energy Beam Welded Joints of TC4 Alloy

Failure Behavior of Laser Metal Deposited Additive Manufacturing Ti-6Al-4V: Effects of Stress State and Initial Defects

Fatigue assessment on 7075/2A12 aluminum alloy friction stir welding lap joints

Microstructure, Variant Selection, and Mechanical Properties of Laser-Welded Ti-4Al-2V Joints

Fatigue inhomogeneity of 140 mm thick TC4 titanium alloy double-sided electron beam welded joints

Effect of Laser Heat Input on Microstructure and Fatigue Behavior of TC17 Titanium Alloy Laser Welded Joint

Experimental Investigation of Laser Peening Effects on Tensile Properties of AA2195-T6 Friction Stir Welded Joints

A Study of Fatigue Damage Evolution on Pulsed Nd:Yag Ti6al4v Laser Welded Joints

Fatigue inhomogeneity of thick 316L stainless steel joints fabricated by ultra-high power laser-MIG hybrid welding

The Low-Cycle Fatigue Behavior, Failure Mechanism and Prediction of SLM Ti-6Al-4V Alloy with Different Heat Treatment Methods