Abstract:Porous polymeric mirospheres have been widely used since their characteristics in the structure.However, the reported methods are less efficient, especially no continuous process was reported to prepare porous polymeric microspheres. Therefore, there is a need to develop a time-saving method with high yield for producing porous polymeric microspheres. This paper reports a continuous process to prepare porous polymeric microspheres via the solvent evaporation method in foam phase, being efficient and of high yield. Preparation of porous poly (methyl methacrylate-co-butyl acrylate) [P (MMA-BA) ] microspheres was carried out in a customized continuous reaction device. At a certain stirring rate and reaction temperature, the oil phase and the aqueous phase were pumped continuously into the reactor. Foam phase gradually generated and flowed out from the outlet of the reactor.Porous P (MMA-BA) microspheres were obtained after collecting the bubble phase followed by defoaming, washing, filtration and drying. The average foam flow rate, the microspheres' yield, the average particle size and the pore structure were investigated as a function of the experimental conditions including the feed rate of the oil phase, the reaction temperature, the stirring rate and the concentration of PVA. The results showed that the reaction temperature was 45℃, the stirring rate was 500 r/min, the oil phase solution feed rate was 30 g/min, the PVA concentration was 1.0％ (mass), and the oil phase solution P (MMA-BA)∶ DCM∶ HT is 10∶ 53∶rnicrospheres was up to 92％ and the average particle size is 130 μm. The temperature and the residual amount of the aqueous phase left in the customized continuous reaction device are critical for the foam behavior and the yield of the porous P (MMA-BA) microspheres. This work validates that the customized continuous reaction device is capable to produce porous polymeric microspheres continuously, based on the method to prepare porous polymeric microspheres via solvent evaporation method in foam phase, with improved efficiency and yield. In addition, the method reported in this work is able to use continuously on an industrial scale potentially.

Solvent Evaporation Self-Motivated Continual Synthesis of Versatile Porous Polymer Microspheres Via Foaming-Transfer

Technical Improvement for Producing Porous Polymer Microspheres in Foam Phase

An efficient preparation of porous polymeric microspheres by solvent evaporation in foam phase

Foam phase preparation of porous poly (methyl methacrylate-co-butyl acrylate) microspheres in continuous process

Controlling the Internal Structures of Polymeric Microspheres Via the Introduction of a Water-Soluble Organic Solvent

Preparation of uniform microcapsules with silicone oil as continuous phase in a micro-dispersion process.

An Airflow-Controlled Solvent Evaporation Route to Hollow Microspheres and Colloidosomes

An improved solvent evaporation method to produce poly (lactic acid) microspheres via foam-transfer

Preparation of porous polystyrene microspheres by using foam phase separation

Fabrication of Porous Polymer Microparticles with Tunable Pore Size and Density Through the Combination of Phase Separation and Emulsion-Solvent Evaporation Approach

Fabrication of porous polymer microspheres by tuning amphiphilicity of the polymer and emulsion–solvent evaporation processing

Highly Crosslinked Poly(ethyleneglycol Dimethacrylate)-Based Microspheres Via Solvothermal Precipitation Polymerization in Alcohol–water System

Microencapsulation Par Évaporation De Solvant

Preparation of Microcapsules with Silicone Oil As Continuous Phase Using A Solvent Evaporation Method

Functional monodisperse microspheres fabricated by solvothermal precipitation co-polymerization

Controllable Morphology and Wettability of Polymer Microspheres Prepared by Nonsolvent Assisted Electrospraying

Surface Microstructure Regulation of Porous Polymer Microspheres by Volume Contraction of Phase Separation Process in Traditional Suspension Polymerization System.

Controllable Inducing Preparation of Polymorphous Hundred-Micron Alumina Microspheres Via Droplet-Based Two-Stage Microfluidic Solvent Extraction Technology

Facile Preparation of Hierarchically Porous Polymer Microspheres for Superhydrophobic Coating

Acoustic-Controlled Bubble Generation and Fabrication of 3D Polymer Porous Materials

Fabrication of Monopile Polymer Foams via Rotating Gas‐Foaming: Hybrid Applications in Solar‐Powered Interfacial Evaporation and Water Remediation