Abstract:Summary Passive seismic inversion at the reservoir scale offers the advantages of low cost, negligible environmental impact, and the ability to probe a target area with low-frequency energy not afforded by even the most modern active-source seismic technology. In order to build starting models suitable for full-waveform wavespeed tomography, characterization of earthquake sources is an indispensable first step. We present a workflow for the centroid moment tensor (CMT) inversion of seismic events identified in a passive seismic data set acquired by a large and dense array of three-component broadband seismic sensors in a mountainous setting in the Himalayan foothills. The dataset comprised 256 instruments operating for 2×4 months over an area of 8,000 km2. An initial three-dimensional (3-D) wavespeed model was determined for the region via the analysis of first-arriving traveltime picks. Of the 2,607 identified seismic events that were well recorded at frequencies between 0.2–50 Hz, 86 with magnitudes 1.3 ≤ M ≤ 3.0 initially had their CMT focal mechanisms determined by a waveform fitting procedure built on a Green’s function approach in a one-dimensional (1-D) layered average wavespeed model, for stations within an offset of 10 km, in the frequency range 0.2–1.4 Hz. Here, we obtain updated CMT mechanisms for the 86 events in that catalog via multicomponent full-waveform inversion in the 3-D wavespeed model. Our workflow includes automated data- and model-driven data selection using a combination of different metrics derived from signal-to-noise considerations and waveform-fitting criteria, and relies upon spectral-element simulations of elastic wave propagation in the 3-D wavespeed model, honoring topography. Starting from the initial CMT solutions, we seek improvement to the data fit within the frequency band 0.5–2.5 Hz by minimizing the waveform difference between observed and synthetic data, while accommodating wavespeed-model errors by allowing for small time-shifts. We balance uneven data coverage and tune their contributions via data-space weighting functions. We quantify the improvements to the data fit in terms of different metrics. We summarize the changes to the CMT solutions, and present and analyze the resulting catalog for the region, including their breakdown into double-couple and non-double couple components, and their relation to mapped faults in the region.

A Moment Tensor Inversion Approach Based On The Correlation Between Defined Functions And Waveforms

Full Waveform Inversion Based on Time-Integral-damping Wavefield

Full Moment Tensor Inversion Constrained by Double-Couple Focal Mechanism for Induced Seismicity*

Single-well Moment Tensor Inversion of Tensile Microseismic Events

Microseismic moment-tensor inversion and sensitivity analysis in vertically transverse isotropic media

Time-damping full waveform inversion of multi-dominant-frequency wavefields

Full moment tensor inversion method of underground nuclear explosions based on surface waves data

Joint Inversion of Centroid Moment Tensor for Large Earthquakes by Combining Teleseismicp-Wave Andw-Phase Records

Multievent Moment-Tensor Inversion for Ill-Conditioned Geometries

Micro-seismic Elastic Reflection Full Waveform Inversion with An Equivalent Source

Discrimination of induced seismicity by full moment tensor inversion and decomposition

Azimuthal Amplitude Difference-Based Multidomain Seismic Inversion for Fracture Weaknesses

A Joint Inversion of Sources and Seismic Waveforms for Velocity Distribution: 1-D and 2-D Examples

A collocated inversion of sources and early arrival waveforms for credible tomograms: Synthetic and field data examples

Full-waveform centroid moment tensor inversion of passive seismic data acquired at the reservoir scale

Geostatistical inversion method based on seismic waveform similarity

An Inversion-Based Microseismic Simulator for Fracture Diagnostics

Moment tensor inversion of perforation shots using distributed acoustic sensing

Numerical Experiments of Moment Tensor Inversion with Rotational Ground Motions

Inversion of Near-Field Waveform Data for Earthquake Source Rupture Process (I): Method and Numerical Test

A New Earthquake Location Method Based on the Waveform Inversion