Abstract:High Performance Polymers, Ahead of Print. Polyimide aerogel, presenting an outstanding new material for lightweight protective thermal insulation, has garnered significant attention in the aerospace field. Despite its potential, due to the high production cost of the supercritical drying method used for its preparation, its widespread application is limited. In this research, a series of lightweight polyimide aerogels (F-PIAs, 3,3',4,4'-biphenyl tetracarboxylic dianhydride (s-BPDA) and 4,4'-diaminodiphenyl ether (ODA)) with excellent thermal protection properties were prepared by lyophilization. The findings indicated that F-PIAs (Freeze-dried polyimide aerogels) exhibited comparable physical characteristics to S-PIAs (Supercritical-dried polyimide aerogels), while their preparation cost was even more economical. F-PIAs exhibits excellent flexible and compression behavior (compression strength up to 1.16 MPa, modulus up to 12.8 MPa), which provide a great structural basis for the production of molded thermal insulation protective materials. The average pore diameter of F-PIAs is in the range of 7∼11 nm. The nanoporous structure leads to the gas within the pores of the aerogel producing the Knudsen effect, thereby significantly enhancing the thermal insulation performance of the aerogel. The thermal conductivity of F-PIA-4 (Freeze-dried polyimide aerogels with a solid content of 4%) at room temperature is as low as 0.023 W·m−1·K−1, which is superior to the PIAs (0.043 W·m−1·K−1) prepared by lyophilization in literature. Its thermal diffusion coefficient changes from 0.108 mm2·s−1 to 0.18 mm2·s−1 in the temperature range of 27°C to 200°C, demonstrating good thermal insulation performance at high temperatures. Meanwhile, after heating on a 150°C flat plate for 11 min and 41 s, the surface temperature of F-PIA-4 was only 36.2°C, further verifying its excellent thermal insulation performance. The results of the TGA experiment on F-PIA-4 demonstrated the high-temperature stability of aerogel (Td5% is higher than 523°C, Td10% is higher than 566°C). The exceptional properties of F-PIAs hold significant practical reference value in helping to reduce the manufacturing cost of high-performance aerogel thermal insulation materials, thereby enabling their widespread application in aerospace, military, and civil field.

Preparation and Application of Polyimide Aerogel Materials

Polyimide Aerogels with Excellent Thermal Insulation, Hydrophobicity, Machinability, and Strength Evolution at Extreme Conditions

Fabrication of Rigid Polyimide Foams with Overall Enhancement of Thermal and Mechanical Properties

Preparation and Properties of High Performance Polyimide Foam

Preparation and Characterization of Polyimide Aerogels with a Uniform Nanoporous Framework

Polyimide aerogels with low thermal conductivity and high-temperature stable properties prepared by lyophilization for flexible thermal protection

Synthesis and Characterization of Rigid and Thermostable Polyimide Aerogel Crosslinked with Tri(3-Aminophenyl)phosphine Oxide

Mechanically Robust Nanoporous Polyimide/Silica Aerogels for Thermal Superinsulation of Aircraft

Ultralow shrinkage polyimide hybrid aerogel composite enhanced with organic fibers for thermal protection

Preparation and Properties of High-Temperature-Resistant, Lightweight, Flexible Polyimide Foams with Different Diamine Structures

Preparation of polyimide aerogels by freeze‐extraction and chemical imidization for 3D printing

Preparation and Performance of Polyimide-Reinforced Clay Aerogel Composites

Polyimide Aerogels Crosslinked Through Cyclic Ladder‐like and Cage Polyamine Functionalized Polysilsesquioxanes

Synthesis of porous polyimide films with low dielectric constant and excellent mechanical properties by ambient pressure drying

Enhancing moisture-resistance in polyimide aerogels: A novel hydrophobic modification approach with ortho -positioned long-chain barriers

Mechanically strong and tough polyimide aerogels cross-linked with amine functionalized carbon nanotubes synthesized by fluorine displacement reaction

Reusable Nanoporous Al2O3-Containing Polyimide Aerogels for Thermal Insulation of Aircraft

Mechanically Strong and Thermally Stable Chemical Cross-Linked Polyimide Aerogels for Thermal Insulator

Fire-resistant Polyimide-Silica Aerogel Composite Aerogels with Low Shrinkage, Low Density and High Hydrophobicity for Aerospace Applications

Highly Thermally Resistant and Flexible Polyimide Aerogels Containing Rigid-rod Biphenyl, Benzimidazole, and Triphenylpyridine Moieties: Synthesis and Characterization

Resilient, Fire-Retardant and Mechanically Strong Polyimide-Polyvinylpolymethylsiloxane Composite Aerogel Prepared Via Stepwise Chemical Liquid Deposition