Abstract:The inclination damage of mortise and tenon (M-T) joints, caused by the looseness between the mortise and tenon, has an detrimental impact on the overall safety of structures. To investigate the effects of varying inclination rotation on the seismic behavior of ancient M-T joints, four 1/3.2-scaled straight M-T joints with different inclination rotation, one intact joint for comparison and three looseness-induced inclined joints, were cyclically tested. Typical failure modes of the damaged joints were identified. The influence of the tilt deterioration on the joint's hysteretic and rotational behavior was evaluated. The test results showed that with an increase in the inclination rotation, the size of the hysteretic loops of the inclined joints was increasingly smaller, the negative initial slippage and pinching effects were more apparent, the ultimate moment-resisting, initial elastic stiffness, and ductility of the specimens degraded significantly. Furthermore, the multi-scale finite element models of the looseness-induced inclined M-T joints were established using the ABAQUS. Based on the validated numerical model, the parameter analysis was performed. The influence of the frictional coefficient of wood, inclined rotation, and horizontal gap between the tenon and mortise on the joint's hysteretic behavior and energy dissipation mechanism was quantified. It is found that with a friction coefficient of 0.6, the positive and negative ultimate moments-resisting of the joint improved 65.99 % and 35.89 %, respectively; the joint's slip moment and energy dissipation increased by 12.18 and 3.78 times, respectively. With a 0.043 rad inclined rotation, the positive and negative ultimate moments of the joint decreased 23.32 % and 30.46 %, respectively; the joint's positive and negative initial elastic stiffnesses and cumulative energy dissipation reduced 49.12 %, 28.96 %, and 56.33 %, respectively. When the inclined rotation remained at 0.022 rad, the positive and negative ultimate moments of the joint including a 6 mm horizontal gap reduced 26.63 % and 34.20 %, respectively; the joint's positive and negative initial elastic stiffnesses, and accumulative energy dissipation decreased 42.42 %, 59.43 %, and 79.50 %, respectively.

Flexural behavior of penetrated mortise-tenon joints

Theoretical Model of Bending Moment for Straight Mortise-and-Tenon Joints with Wooden Pegs Involving a Gap

Study on the strength mechanism of the wooden round-end mortise-and-tenon joint using the digital image correlation method

Research on Mechanical Properties of Main Joints of Chinese Traditional Timber Buildings with the Type of Post-and-Lintel Construction

Fatigue and damage evolution in wood T-shaped mortise and tenon joints

A finite element model of semi-rigid mortise-and-tenon joint considering glue line and friction coefficient

Experimental Study on the Traditional Timber Mortise-Tenon Joints

Experimental Study and Numerical Simulation Analysis on Reinforcement of Mortise-Tenon Joints with Flat Steel Strips

Numerical and Optimal Study on Bending Moment Capacity and Stiffness of Mortise-and-Tenon Joint for Wood Products

Study on geometric optimization for new type of steel mortise and tenon joint based on performance

Numerical and mechanical research on withdrawal capacity of parallel-to-grain connection part of mortise and loose tenon joint for wooden furniture

Experimental and Numerical Study on Methods of Testing Withdrawal Resistance of Mortise-and-Tenon Joint for Wood Products

Flexural performance of mortise–tenon wet joints in prefabricated ribbed beam bridges

Cracking simulation and analysis of the mortise-and-tenon wet joints in Precast reinforced concrete ribbed girder Bridges

A Mechanical Model Used for the Multifactor Analysis of Through-Tenon Joints in Traditional Chinese Timber Structures

A novel method and validation for obtaining the optimal interference fit of round-end mortise-and-tenon joint

Seismic behavior of looseness-induced inclined mortise and tenon joints in ancient timber structures: Experimental tests, multi-scale finite element model, and behavior degradation

Experimental study on seismic performance of Chinese traditional mortise and tenon joints with different lengths that tenons pull out of mortise

Moment-Rotation Calculation Method and Parameter Analysis for Loose Continuous-Tenon Joint in Column-And-Tie Timber Structure

Study on the seismic performance of through-tenon joints with pullout tenon gaps between mortise and tenon shoulder

Investigating the Influence of Tenon Dimensions on White Oak (Quercus alba) Mortise and Tenon Joint Strength