Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Basic Research and Development of the Influence Mechanism of Two-stage Turbocharged Flow Characteristics on High Density Low Temperature Combustion Process of Diesel Engine

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Methodology to Separate the Two Burn Stages of Natural-Gas Lean Premixed-Combustion Inside a Diesel Geometry

Numerical Simulation on High Density-Low Temperature Combustion in Diesel Engines

Investigation of the Effect of Simulated Atmospheric Conditions at Different Altitudes on the Combustion Process in a Heavy-Duty Diesel Engine Based on Zero-Dimensional Modeling

The Influence of Nozzle Parameters on the Atomization Performance of Non-normal Fuel based on the Super-high Pressure Common Rail System

Effect of Optimization Matching Between Post Injection Technology and Two-Stage Turbocharging System on Combustion Process

Study of In-Cylinder Heat Transfer Boundary Conditions for Diesel Engines under Variable Altitudes Based on the CHT Model

Numerical Investigation on New Engine Combustion Charactristic of Helicopter

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Simulation and Optimization of Low Temperature Combustion in Diesel Engine at High Load

Experiment on Low Temperature Combustion of Gasoline Homogeneous Charge Induced Ignition by Diesel

Application of CFD, Taguchi Method, and ANOVA Technique to Optimize Combustion and Emissions in a Light Duty Diesel Engine

Exhaust Emission and Thermal Efficiency of Vehicle Heavy Duty Diesel Engine at Low Load

Research on low temperature combustion of homogeneous charge induced ignition (HCII) in a light-duty diesel engine

Investigation of Influence of Two-Stage Turbocharging System on Engine Performance Using A Pre-Design Model

Study of the Influence of Key Parameters on the Dynamic Spray Characteristics of Natural Gas Direct Injection Engine

Numerical Investigation of Combustion and Emission With Different Diesel Surrogate Fuel by Hybrid Breakup Model

The Research and Development of a Jet Disturbance Combustion System for Heavy-Duty Diesel Engines

Effects of mixing and chemical parameters on homogeneous charge induced ignition combustion based on a light-duty diesel engine with ultra-Low NOx and soot emissions and high thermal efficiency

Experimental Investigation and Numerical Modeling of Spray Combustion and Emission in a Diesel Engine