Accelerator mass spectrometry for long-lived heavy ion 236 u at ciae *
Wang Xianggao,Shen Hongtao,Jiang Shan,He Ming,Dong Kejun,Li Chaoli,Wang Wei,Wu Shaoyong,Bao Yiwen,Guan Xialing,Hu Yueming,You Qubo,Zhang Dawei,Shi Guozhu,Huang Chuntang
2009-01-01
Abstract:U is a long-lived radioactive isotope with a half-life of 2.342(3) ×10 a, which produced principally by thermal neutron capture on U. U is potentially applied in geological research and nuclear safeguards. Accelerator mass spectrometry (AMS) is presently the most sensitive technique for the measurement of U. A method for AMS measurement of long-lived heavy ion U was developed at CIAE with the set up the AMS dedicated injector and the newly proposed PbO2 molecular ions for the simulation of U ion transport. A sensitivity of lower than 10 has been achieved for isotopic ratio U/U in present work. INTRODUCTION U is a long-lived radioactive isotope with a half-life of 2.342(3) ×10 a, mainly produced by the thermal neutron induced U(n,γ) U reaction. The isotopic ratio of U/U in nature is about 10, depending strongly on the integral thermal neutron flux received by the material. This makes U usable as an integrating neutron monitor over the last 100 million years [1], and potentially applicable in geological research [2]. The isotopic ratio of U/U could also be used as a “fingerprint” for indicating the presence of neutronirradiated uranium usually originated from nuclear activities [3]. Recently, several efforts have been made to measure U in environmental samples using techniques based on mass spectrometry such as high-resolution inductively coupled plasma spectrometry (HR-ICPMS), thermal ionization mass spectrometry (TIMS) and accelerator mass spectrometry (AMS). However, detection limits with conventional mass spectroscopy for U/U are ~10, leading to errors larger than 50% for uranium ore samples[4, 5]. Therefore the measurement of natural U is difficult or even impossible without AMS. AMS offers significant advantages over conventional mass spectroscopic methods in high sensitivity, smaller sample size, relatively free from isomer and molecular-ion interferences, and shorter measurement time. AMS measurement of actinides was presented firstly by IsoTrace facility X.L. Zhao et al. of Toronto group [6], in which the U/U is lower than 5×10 in a natural uranium ore from Cigar Lake deposit in Canada. The natural U/U has also been measured by several other groups, such as: VERA [7], ANU [8], LLNL [9], ANSTO [10], Munich [11], ETH [12] and Israel Weizmann Institute [13]. In this paper, a method for AMS measurement of longlived heavy ion U developed on the HI-13 Accelerator at China Institute of Atomic Energy (CIAE) is reported. The unique features include establishing of the AMS dedicated injector and the newly proposed PbO2 molecular ions for the simulation of U ion transport. THE AMS DEDICATED INJECTOR There is a general rule in AMS that a high mass resolution analyzer is needed to separate the neighboring interference and a high energy resolution analyzer is required to clip the tail of the high energy. The original injector setup at CIAE [14] with the mass resolution of M M Δ ~220, could not satisfy the requirement for AMS measurement of heavy isotopes (e.g., U, Hf, Sm). Therefore, a high resolution dedicated injector for AMS was developed, as shown in Fig. 1. The new injector adopts achromatic technique, which consists of a 90o electrostatic analyzer (ESA) and a 112o double-focusing analyzing magnet (MA). A triplet electric quadruple lens and a single electric quadruple lens were mounted at the entrance and the exit of the ESA beam line, respectively, for ions focusing. This spherical 90o ESA with 750 mm radius, has maximum electric field strength of 4 kV/cm and provides both horizontal and vertical focusing. The 112o double-focusing MA with a bending radius of 800 mm, has a maximum magnetic field of 1.3 T. The energy resolution of the electrostatic deflector