Review of Research on Mechanism of Drag Reduction by Polymer Additives

Xue-ming SHAO,Jian-zhong LIN

DOI: https://doi.org/10.3969/j.issn.1673-3851.2001.01.004

2001-01-01

Abstract:A comprehensive review is given to researches on mechanism of drag reduction by additives. The opinion of viscous anisotropic stresses is introduced.

What problem does this paper attempt to address?

Review of Research on Drag Reduction

Wang Yingkui,Jiang Chunbo,Li Ling

DOI: https://doi.org/10.3969/j.issn.0559-9342.2008.02.022

2008-01-01

Abstract:"Drag Reduction" is a hotspot research of the hydrodynamics with more and more research work and applications.Many drage reduction methods are used widely,and the mechanism research of these methods are also developing.Generally speaking,the thickening of the viscous sublayer is the main academic reason.In all the methods,Polymer additive is an effective method,widely applying in the area such as petroleum transportation,fire protection and shipping.The mechanism research of such a remarkable method has developed "Viscoelastic theory","Stress anisotropic theory" and so on.But the research work of the drag reduction is not so mature,need more further development.
Experimental research on drag reduction by polymer additives in a turbulent pipe flow

Shao Xueming,Lin Jianzhong,Wu Tao,Li Yulin

DOI: https://doi.org/10.1002/cjce.5450800215

2002-01-01

Abstract:In order to investigate the effects of injection position on drag reduction as well as further the effects of polymer additives on turbulent structures, LDA measurements of turbulent pipe flows were conducted. The results show that the amount of drag I eduction grows with the increase of the Reynolds number, and injecting the polymer at the centre of pipe is more effective than at the wall. Due to the addition of polymer solution, the axial, radial r.m.s. velocity fluctuations and Reynolds stress decrease over the entire pipe cross-section, the time auto-correlation coefficients of axial and radial velocity fluctuation at the centre of pipe decay more slowly, the number of spectrum peaks is decreased, and the peak shifts towards lower wave numbers. The results also reveal that, due to the addition of polymer solution, the large-scale vortices are enhanced and small-scale vortices are suppressed.
Analysis of the Drag Reduction Performance and Rheological Properties of Drag-Reducing Additives

Ailian Chang,Le Huang,Song Wei,Minglu Shao

DOI: https://doi.org/10.3390/polym16091247

IF: 5

2024-04-30

Polymers

Abstract:In the practical application of hydraulic rotating machinery, it is essential to thoroughly explore drag reduction and rheological characteristics of drag-reducing additives to optimize machinery efficiency and reduce equipment consumption. This paper combines simulation and experimental approaches to investigate the drag-reduction performance and rheological properties of drag-reducing additives. Numerical simulations are initially conducted to investigate the shear-thinning properties of drag-reducing fluid and explore variations in drag-reduction rate. Turbulent phenomena characteristics are described by analyzing turbulent statistical quantities. Subsequently, the rheological behaviors of polyethylene oxide (PEO), cetyltrimethyl ammonium chloride (CTAC), and their mixed solutions under different conditions are scrutinized using a rotational rheometer. The findings indicate that the drag reduction effect amplifies as the rheological index n and characteristic time λ decrease. The numerical simulations show a maximum drag reduction rate of 20.18%. In rheological experiments, a three-stage viscosity variation is observed in single drag-reducing additives: shear thickening, shear thinning, and eventual stabilization. Composite drag-reducing additives significantly reduce the apparent viscosity at low shear rates, thereby strengthening the shear resistance of the system.

polymer science
Drag Reduction Induced by Polymer in Turbulent Pipe Flows

Shu-Qing Yang,Donghong Ding

DOI: https://doi.org/10.1016/j.ces.2013.07.048

IF: 4.7

2013-01-01

Chemical Engineering Science

Abstract:This paper deals with the velocity distribution and friction factor of polymer drag reducing flows in smooth pipes. By applying the concept of elastic shear stress or the Reynolds shear stress deficit, the equations of velocity distribution and friction factor in turbulent drag reducing flows are derived. Based on the derived equations, the onset Reynolds number for drag reduction is discussed which shows that the onset of drag reduction depends on the polymer type and its concentration. The optimal polymer concentration for Maximum Drag Reduction (MDR) is obtained, and it depends only on the polymer species. The effect of polymer mechanical degradation is discussed in the current paper.
Polymer additives reduce fluid drag in turbulent flow

H. Richard Leuchtag

DOI: https://doi.org/10.1063/1.2994963

IF: 3.5

1978-03-01

Physics Today

Abstract:The study of turbulence in fluid dynamics has recently advanced in several new directions, and at the same time has gone a long way towards solving a problem: the uncanny efficacy of tiny amounts of polymer additives in reducing the drag between solids and liquids in turbulent flow. The phenomenon, which may well prove a boon to farmers and firefighters, has also begun to help improve our understanding of a fundamental problem in fluid dynamics, the structure and onset of turbulence. According to François Frenkiel (David W. Taylor Naval Ship Research and Development Center), the new directions include the recognition of coherent phenomena intermixed with quasistatistical effects. New visualization techniques on the one hand, and high-speed computing methods (for data analysis as well as modelling) on the other, have brightened the outlook in the field. Much of the recent work in drag reduction is summarized in a recent volume of The Physics of Fluids, containing the proceedings of a 1976 meeting.

physics, multidisciplinary
Research progress concerning turbulent drag reduction of surfactant solution

Jinjia WEI,Chonghai HUANG,Na XU

DOI: https://doi.org/10.16085/j.issn.1000-6613.2016.06.007

2016-01-01

Abstract:In turbulent flow drag reduction applications,surfactant additive is more applicable than polymer for the flow with high shear or in the closed circulation system due to its reversible mechanical degradation advantage. However,there is not enough understanding of the complicated rheology and drag-reduction mechanism of surfactant solution,limiting its practical application in the drag reduction field. This review introduces the research progress of surfactant drag reduction conducted by the authors in recent years on microstructure,complicated rheology characteristics, turbulent structure,as well as their relations with drag reduction and heat transfer,and analyzes the combined drag reduction effect of surfactant additives in the flow and microgroove fabricated on the wall. The stretch devices can significantly improve the heat transfer performance of surfactant drag-reducing flow with a lower pressure loss penalty. To the shortages of present surfactant drag reduction research,several suggestions are given for the future study. The first is to develop environmentally friendly and effective surfactant,the second is optimal design and layout of heat transfer enhancement device for drag-reducing flow,the third is the study on synergetic effect of drag reduction by combing surfactant drag reduction and other drag-reducing ways,and the final one is practical industrial application research on the scale-up,anticorrosion and persistence effect of surfactant drag reduction.
Direct Numerical Simulation on Drag-Reducing Flow by Polymer Additives Using A Spring-Dumbbell Model

Yi Wang,Bo Yu,Jin-jia Wei,Feng-chen Li,Yasuo Kawaguchi

DOI: https://doi.org/10.1504/pcfd.2009.024822

2009-01-01

Abstract:A discrete-element model (spring-dumbbell model) is used to investigate the mechanism of drag-reduction by adding polymer in a turbulent channel flow of Newtonian fluid by Direct Numerical Simulations (DNSs). By using this model, the spatial concentration of the polymer can be obtained numerically. In this paper, the effect of the spring coefficient on the drag-reduction is studied in detail. The quantitative relations between the drag-reduction rate and viscoelastic and Reynolds shear stress, etc., are obtained. Discussions are performed to clarify the relation between the turbulent structure of the polymer drag-reducing flow and the spring coefficient of the discrete-element model.
A note to further explain the mechanism of turbulent flow drag reduction by polymer from chemistry view

Xin Zhang,Xiaodong Dai,Jishi Zhao,Dengwei Jing,Fei Liu,Lei Li,Yanping Xin,Kun Liu

DOI: https://doi.org/10.22541/au.162094956.60598260/v1

2021-01-01

Abstract:In our previous work regarding the mechanism of drag reduction and degradation by flexible linear polymers, we proposed a correlation based on the Fourier series to predict the drag reduction and its degradation, where a phase angle was involved, but the physical meaning for the correlation especially of the employed phase angle was not clear, which is however important for reasonable explanation of the drag reduction mechanism over flexible linear polymers. This letter aims to clarify this issue. We use several steps of deduction from the viscoelastic theory, and conclude that the Fourier series employed to predict the drag reduction and its degradation is due to viscoelastic property of drag-reducing polymer solution, and the phase angle represents the hysteresis of polymer in turbulent flow. Besides, our new view of drag reduction by flexible polymers can also explain why a maximum drag reduction in rotational flow appears before degradation happens.
Study on the Shear Degradation Law of Polymer Drag Reducing Agents

Shiyi Lv,Chuanxian Li,Xinyuan Li,Wang Lu,Wu Zhang,Bo Yao,Guangyu Sun,Fei Yang

DOI: https://doi.org/10.1088/1742-6596/2834/1/012089

2024-01-01

Journal of Physics Conference Series

Abstract:Abstract The use of drag reducing agents in oil pipeline transportation can reduce driving energy consumption and has certain energy-saving benefits. However, irreversible degradation occurs when polymer drag reducing agents are sheared through pumping. In order to study the viscosity loss of polymer drag reducing agents caused by mechanical shear during the pumping process, the combination of methods such as a rotational rheometer and an indoor drag reducing loop testing system was used to test and analyze the rheological and drag reducing properties of the drag reducing agent solution, and to study the shear degradation law of polymer drag reducing agent solution under different conditions. The results showed that the shear stress of the polymer drag reducing agent solution increased with the increase in shear rate, and the viscosity increased with the increase of shear stress, showing shear thickening. When the polymer drag reducing agent solution is not sheared, the drag reduction rate increases and then decreases with the increase of concentration, and reaches the maximum value at 20 mg·L−1. However, after shear, the drag reduction performance decreases rapidly, but the high concentration still maintains a good drag reduction rate. The research results provide a theoretical basis for improving the performance of polymer drag reducing agents under different operating conditions and play a guiding role in further improving and perfecting the polymer drag reducing technology.
Experimental study on drag reduction performance of mixed polymer and surfactant solutions

Dongjie Liu,Qinghui Wang,Jinjia Wei

DOI: https://doi.org/10.1016/j.cherd.2018.01.047

IF: 4.119

2018-01-01

Chemical Engineering Research and Design

Abstract:•Intensification of drag reduction effect by mixed surfactant and polymer system.•Comparison of drag reduction performance of pure and mixed solutions.•Reinforced concrete structure was proposed to explain the mechanism.•The influence of temperatures about the mixed solutions on drag reduction effect.
Mechanistic Study of Drag Reduction in Turbulent Pipeline Flow over Anionic Polymer and Surfactant Mixtures

Yanlin Chai,Xianwen Li,Jiafeng Geng,Jiaxin Pan,Yalong Huang,Dengwei Jing

DOI: https://doi.org/10.1007/s00396-019-04525-2

IF: 2.4

2019-01-01

Colloid & Polymer Science

Abstract:The mixed aqueous solutions of anionic surfactant sodium dodecyl sulfate with polymer polyacrylamide of various kinds, i.e., cationic, anionic, nonionic, and zwitterion, were firstly tested to study their synergistic effect on drag reduction performance. The optimal combination of sodium dodecyl sulfate with anionic polyacrylamide was confirmed due to their strong hydrophobic interaction and electrostatic repulsion caused by the same charge. The surface tension, conductivity, and viscosity of pure surfactant solution and mixed solutions at different surfactant concentrations with anionic polymer of certain concentration were tested, and their drag reduction behavior in pipe flow was also investigated experimentally. It turns out that drag reduction performance acquired from the combination of anionic surfactant and anionic polyacrylamide is better than either of the single additive, especially under high shear rate. For the mixtures, the degree of drag reduction is strongly dependent on the concentration of SDS and more pronounced in the high Reynolds number range. The best drag reduction performance is obtained for the SDS concentration around the polymer saturation point. Our work should be of value for the drag reduction in the application such as shale gas fracturing and various fluid transports.
Enhanced drag reduction performance by interactions of surfactants and polymers

Dongjie Liu,Steven Wang,Igor Ivitskiy,Jinjia Wei,Ophelia K. C. Tsui,Fei Chen

DOI: https://doi.org/10.1016/j.ces.2020.116336

IF: 4.7

2021-01-01

Chemical Engineering Science

Abstract:The interactions of cationic surfactant cetyltrimethyl ammonium chloride (CTAC) and polyacrylamide (PAM) in drag reduction solutions are studied by experiments and simulations. Cryogenic Transmission Electron Microscopy shows that CTAC and PAM form aggregates with interconnected network structures, and the bridge effect from polymers can improve the network structures' density. The associated potential of mean force (PMF) value indicates that surfactant/polymer attractions contribute to the formation of aggregates. Meanwhile, the mechanism of the enhanced drag reduction performance of surfactant/polymer solution is discussed by the extension energy of the aggregate structures. It is found that the interactions of surfactants and polymers help to improve the anti-shear performance of the surfactant micelles. Furthermore, polymers can balance micelles energy distribution, postpone the appearance of energy extreme point, and delay the rupture of micelles. This work fundamentally demonstrates that interactions and strengthened structures of micelle aggregates can intensify drag reduction in surfactant/polymer solutions. (C) 2020 Elsevier Ltd. All rights reserved.
Studies on the synthesis of drag reduction polymer PLMA and the shear stability

Shoujia Sun,Tong Zheng,Fengxiang Chen

1999-01-01

Abstract:A method of synthesizing the oil-soluble drag reduction polymer PLMA (poly dodecyl methylacryate)by latex polymerization was presented. The effects of PLMA's relative molecular mass, content, temperature and flow state on the drag reduction effectiveness and the shear stability were discussed. Mathematical models of drag reduction effectiveness in relation to relative molecular mass and content through recursive analysis by computer were provided. Finally, a further interpretation of the experiment result was given according to the theory of turbulence simulating order structure.
Prediction and New Insight for the Drag Reduction of Turbulent Flow with Polymers and Its Degradation Mechanism.

Xin Zhang,Xiaodong Dai,Qiaorong Han,Jishi Zhao,Dengwei Jing,Fei Liu,Lei Li,Yanping Xin,Kun Liu

DOI: https://doi.org/10.1021/acs.jpclett.1c02027

IF: 6.888

2021-01-01

The Journal of Physical Chemistry Letters

Abstract:A physicochemical understanding of the mechanism of turbulent flow drag reduction with polymer and its degradation is of great interest from both science and industry perspectives. Although the correlation based on the Fourier series has been proposed to predict the drag reduction and its degradation, its physical meaning was not clear until now. This letter aims to clarify this issue. We develop a comprehensive model to predict the drag reduction and degradation of polymers in turbulent flow from a chemical thermodynamics and kinetics viewpoint. We demonstrate that the Fourier series employed to predict the drag reduction and its degradation is due to the viscoelastic property of drag-reducing polymer solution, and the phase angle in the model, in physical nature, represents the hysteresis of the polymer in turbulent flow. Besides, our new insight of drag reduction with flexible polymers can also explain why a maximum drag reduction in rotational flow appears before degradation happens.
Colloquium: Theory of Drag Reduction by Polymers in Wall Bounded Turbulence

Itamar Procaccia,Victor S. L'vov,Roberto Benzi

DOI: https://doi.org/10.1103/RevModPhys.80.225

2007-02-15

Abstract:The flow of fluids in channels, pipes or ducts, as in any other wall-bounded flow (like water along the hulls of ships or air on airplanes) is hindered by a drag, which increases many-folds when the fluid flow turns from laminar to turbulent. A major technological problem is how to reduce this drag in order to minimize the expense of transporting fluids like oil in pipelines, or to move ships in the ocean. It was discovered in the mid-twentieth century that minute concentrations of polymers can reduce the drag in turbulent flows by up to 80%. While experimental knowledge had accumulated over the years, the fundamental theory of drag reduction by polymers remained elusive for a long time, with arguments raging whether this is a "skin" or a "bulk" effect. In this colloquium review we first summarize the phenomenology of drag reduction by polymers, stressing both its universal and non-universal aspects, and then proceed to review a recent theory that provides a quantitative explanation of all the known phenomenology. We treat both flexible and rod-like polymers, explaining the existence of universal properties like the Maximum Drag Reduction (MDR) asymptote, as well as non-universal cross-over phenomena that depend on the Reynolds number, on the nature of the polymer and on its concentration. Finally we also discuss other agents for drag reduction with a stress on the important example of bubbles.

Chaotic Dynamics,Fluid Dynamics
Turbulent Drag Reduction in Plane Couette Flow Wit H Polymer Additives: a Direct Numerical Simulation Study

Hao Teng,Nansheng Liu,Xiyun Lu,Bamin Khomami

DOI: https://doi.org/10.1017/jfm.2018.242

IF: 3.7

2018-01-01

Journal of Fluid Mechanics

Abstract:Drag reduction (DR) in plane Couette flow (PCF) induced by the addition of flexible polymers has been studied via direct numerical simulation (DNS). The similarities and differences in the drag reduction features of PCF and plane Poiseuille flow (PPF) have been examined in detail, particularly in regard to the polymer-induced modification of large-scale structures (LSSs) in the near-wall turbulence. Specifically, it has been demonstrated that in the near-wall region, drag-reduced PCF has features similar to those of drag-reduced PPF; however, in the core region, intriguing differences are found between these two drag-reduced shear flows. Chief among these differences is the significant polymer stretch that arises from the enhanced exchanges between elastic potential energy and turbulent kinetic energy and the commensurate observation of peak values of the conformation tensor components $\unicode[STIX]{x1D60A}_{yy}$ and $\unicode[STIX]{x1D60A}_{zz}$ in this region. This finding is in stark contrast to that of drag-reduced PPF where the polymer stretch and the exchanges between elastic potential energy and turbulent kinetic energy in the core region are insignificant; to this end, in drag-reduced PPF, peak values of the conformation tensor components appear in the near-wall region. Therefore, this study paves the way for understanding the underlying flow physics in drag-reduced PCF, particularly in the context of elastic theory. Moreover, the longitudinal large-scale streaks at the channel centre of drag-reduced PCF are greatly strengthened due to the increased production/dissipation ratio; the LSS imprint effects on the near-wall flow of drag-reduced PCF monotonically increase as the Weissenberg number is enhanced.
Impact of the Microstructure of Polymer Drag Reducer on Slick-Water Fracturing

Zhi-yu Liu,Fu-jian Zhou,Hong-yan Qu,Zhao Yang,Yu-shi Zou,Dao-bin Wang

DOI: https://doi.org/10.1155/2017/9080325

IF: 2.006

2017-01-01

Geofluids

Abstract:Many studies have focused on the drag reduction performance of slick-water, but the microdrag reduction mechanism remains unclear since the microstructure of the drag reducer and its effect on this mechanism have not been well studied. In this study, the microstructure of the drag reducer in slick-water was effectively characterized by transmission electron microscopy. The viscoelasticity and drag reduction performance of the drag reducer with different microstructures were then investigated. Further, the effects of the microstructure of the drag reducer on the viscoelasticity and drag reduction performance of slick-water were analyzed. The results demonstrated that the viscoelasticity of slick-water is governed by the microstructure of the drag reducer, which exhibits a network structure. In addition, the drag reduction performance is related to the viscoelasticity. At low flow rates, the drag reduction performance is dominantly influenced by viscosity, whereas, at high flow rates, it is governed mainly by elasticity. Furthermore, the drag reducer with a uniformly distributed network structure exhibits the most stable drag reduction performance. This drag reducer was used in a field test and the obtained results were consistent with those of a laboratory experiment.
Turbulent drag reduction in plane Couette flow with polymer additives: a direct numerical simulation study

Hao Teng,Nansheng Liu,Xiyun Lu,Bamin Khomami

DOI: https://doi.org/10.1017/jfm.2018.242

IF: 3.7

2018-05-08

Journal of Fluid Mechanics

Abstract:Drag reduction (DR) in plane Couette flow (PCF) induced by the addition of flexible polymers has been studied via direct numerical simulation (DNS). The similarities and differences in the drag reduction features of PCF and plane Poiseuille flow (PPF) have been examined in detail, particularly in regard to the polymer-induced modification of large-scale structures (LSSs) in the near-wall turbulence. Specifically, it has been demonstrated that in the near-wall region, drag-reduced PCF has features similar to those of drag-reduced PPF; however, in the core region, intriguing differences are found between these two drag-reduced shear flows. Chief among these differences is the significant polymer stretch that arises from the enhanced exchanges between elastic potential energy and turbulent kinetic energy and the commensurate observation of peak values of the conformation tensor components $\unicode[STIX]{x1D60A}_{yy}$ and $\unicode[STIX]{x1D60A}_{zz}$ in this region. This finding is in stark contrast to that of drag-reduced PPF where the polymer stretch and the exchanges between elastic potential energy and turbulent kinetic energy in the core region are insignificant; to this end, in drag-reduced PPF, peak values of the conformation tensor components appear in the near-wall region. Therefore, this study paves the way for understanding the underlying flow physics in drag-reduced PCF, particularly in the context of elastic theory. Moreover, the longitudinal large-scale streaks at the channel centre of drag-reduced PCF are greatly strengthened due to the increased production/dissipation ratio; the LSS imprint effects on the near-wall flow of drag-reduced PCF monotonically increase as the Weissenberg number is enhanced.

mechanics,physics, fluids & plasmas
Polymer-Induced Drag Reduction in Dilute Newtonian and Semi-Dilute Non-Newtonian Fluids: An Assessment of the Double-Gap Concentric Cylinder Method

Stefanos Michaelides,Kotaybah W. Hashlamoun,Thibaut Charpentier,Gregory de Boer,Paul Hunt,Helen Sarginson,Claire Ward,Nashaat N. Nassar,Mark C. T. Wilson,David Harbottle

DOI: https://doi.org/10.1021/acs.iecr.2c00899

2022-08-09

Abstract:Polymer-induced drag reduction (DR) in fluids was studied using a rotational rheometer with double-gap concentric cylinder geometry. Although both polymers (polyacrylamide (PAM) and 2-acrylamido-2-methylpropane sulfonic acid (SPAM)) had molecular weights of several MDa, the contrasting polymer charge, nonionic and anionic, led to different polymer overlap concentrations (c*), PAM ≫ SPAM, and fluid rheology, with PAM fluids mostly Newtonian and SPAM fluids non-Newtonian (shear-thinning). Based on...

engineering, chemical
Global drag reduction and local flow statistics in Taylor-Couette turbulence with dilute polymer additives

Yi-Bao Zhang,Yaning Fan,Jinghong Su,Heng-Dong Xi,Chao Sun

2024-12-05

Abstract:We present an experimental study on the drag reduction by polymers in Taylor-Couette turbulence at Reynolds numbers ($Re$) ranging from $4\times 10^3$ to $2.5\times 10^4$. In this $Re$ regime, the Taylor vortex is present and accounts for more than 50\% of the total angular velocity flux. Polyacrylamide polymers with two different average molecular weights are used. It is found that the drag reduction rate increases with polymer concentration and approaches the maximum drag reduction (MDR) limit. At MDR, the friction factor follows the $-0.58$ scaling, i.e., $C_f \sim Re^{-0.58}$, similar to channel/pipe flows. However, the drag reduction rate is about $20\%$ at MDR, which is much lower than that in channel/pipe flows at comparable $Re$. We also find that the Reynolds shear stress does not vanish and the slope of the mean azimuthal velocity profile in the logarithmic layer remains unchanged at MDR. These behaviours are reminiscent of the low drag reduction regime reported in channel flow (Warholic et al., Exp. Fluids, vol. 27, issue 5, 1999, p. 461-472). We reveal that the lower drag reduction rate originates from the fact that polymers strongly suppress the turbulent flow while only slightly weaken the mean Taylor vortex. We further show that polymers steady the velocity boundary layer and suppress the small-scale Görtler vortices in the near-wall region. The former effect reduces the emission rate of both intense fast and slow plumes detached from the boundary layer, resulting in less flux transport from the inner cylinder to the outer one and reduces energy input into the bulk turbulent flow. Our results suggest that in turbulent flows, where secondary flow structures are statistically persistent and dominate the global transport properties of the system, the drag reduction efficiency of polymer additives is significantly diminished.

Fluid Dynamics

Review of Research on Mechanism of Drag Reduction by Polymer Additives

Review of Research on Drag Reduction

Experimental research on drag reduction by polymer additives in a turbulent pipe flow

Analysis of the Drag Reduction Performance and Rheological Properties of Drag-Reducing Additives

Drag Reduction Induced by Polymer in Turbulent Pipe Flows

Polymer additives reduce fluid drag in turbulent flow

Research progress concerning turbulent drag reduction of surfactant solution

Direct Numerical Simulation on Drag-Reducing Flow by Polymer Additives Using A Spring-Dumbbell Model

A note to further explain the mechanism of turbulent flow drag reduction by polymer from chemistry view

Study on the Shear Degradation Law of Polymer Drag Reducing Agents

Experimental study on drag reduction performance of mixed polymer and surfactant solutions

Mechanistic Study of Drag Reduction in Turbulent Pipeline Flow over Anionic Polymer and Surfactant Mixtures

Enhanced drag reduction performance by interactions of surfactants and polymers

Studies on the synthesis of drag reduction polymer PLMA and the shear stability

Prediction and New Insight for the Drag Reduction of Turbulent Flow with Polymers and Its Degradation Mechanism.

Colloquium: Theory of Drag Reduction by Polymers in Wall Bounded Turbulence

Turbulent Drag Reduction in Plane Couette Flow Wit H Polymer Additives: a Direct Numerical Simulation Study

Impact of the Microstructure of Polymer Drag Reducer on Slick-Water Fracturing

Turbulent drag reduction in plane Couette flow with polymer additives: a direct numerical simulation study

Polymer-Induced Drag Reduction in Dilute Newtonian and Semi-Dilute Non-Newtonian Fluids: An Assessment of the Double-Gap Concentric Cylinder Method

Global drag reduction and local flow statistics in Taylor-Couette turbulence with dilute polymer additives