Abstract:CO2 flooding is a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in oil recovery; yet, a comprehensive quantitative analysis remains an area in need of refinement. In this study, we developed 1-D and 2-D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns were determined. A novel approach to the contour area calculation method was introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding the geological parameters, oil viscosity, and injection–production parameters. Furthermore, the Random Forest (RF) algorithm was employed to identify the controlling factor of the sweep coefficient, as determined through the use of out-of-bag (OOB) data permutation analysis. The results showed that the miscible front was located at the point of maximum CO2 content in the oil phase. The immiscible front occurred at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moved at a faster rate compared with the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impacted the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibited the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio was a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection–production parameters also played a pivotal role in terms of the sweep coefficient. Decreased well spacing and increased gas injection rates were found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates could improve the miscibility degree of partly miscible flooding from 0.69 to 1.0. Oil viscosity proved to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly miscible flooding patterns. Conversely, gravity segregation primarily governed the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerged as a paramount influence, with a factor importance value (FI) reaching 1.04. The findings of this study can help for a better understanding of sweeping rules of CO2 flooding and providing valuable insights for optimizing oil recovery strategies in the field applications of CO2 flooding.

Study on streamline distribution of CO2 inj ection-production well pattern

The Three-Dimensional Heterogeneous Simulation Study of CO2 Flooding in Low-Permeability Reservoirs

The research on high efficiency water injection development of carbonate rock reservoir in the middle east

Investigation on water-drive performance of a fault-karst carbonate reservoir under different well patterns and injection-production modes based on 2D visualized physical models

Injection-production optimization of carbonate reservoir based on an inter-well connectivity model

Laboratory Study on the Oil Displacement Process in Low-Permeability Cores with Different Injection Fluids

Using Cyclic Injection-production Technology to Improve the Development Effect of Water Flooding in Ultra-high Water Cut Stage

Optimization of CO2 immiscible injection incomplex low permeability reservoir

Front Movement and Sweeping Rules of CO2 Flooding under Different Oil Displacement Patterns

Study on Enhanced Oil Recovery Mechanism of CO 2 Miscible Flooding in Heterogeneous Reservoirs under Different Injection Methods

COMSOL-based investigation of the characteristics of microscopic water flooding and residual oil distribution in carbonate reservoirs

The application of morphological operations, level sets, and phase field methods in CO 2 displacement

Exploration and Practice of CO2 Huff-N-Puff Combined CO2 Flooding in Shale Oil Well Cluster Group

Simulation Study of Allied In-Situ Injection and Production for Enhancing Shale Oil Recovery and CO2 Emission Control

Study on enhancing oil recovery by CO2 injection in low permeability reservoir

Research on the Differential Oil Producing in the Various Scale Pores under Different CO 2 Flooding Modes with a Fluid Distribution Pore Classification Method

Study on Microscopic Water Flooding in Porous Carbonate Reservoirs by Numerical Simulation

Investigation on the flow behavior and mechanisms of water flooding and CO2 immiscible / miscible flooding in shale oil reservoirs

Residual Oil Distribution Pattern in a Fault-Solution Carbonate Reservoir and Countermeasures to Improve Oil Development Effectiveness

Application of a Multistage Plugging System in a Fractured Reservoir of CO 2 Flooding

Experimental investigation of carbon dioxide flooding in heavy oil reservoirs for enhanced oil recovery