Abstract:Elasto-plastic numerical analyses have been carried out for bonded dissimilar materials with different hardening properties, by using the boundary element method (BEM) and the finite element method (FEM). From the stress distribution near the interface edge, the elasto-plastic singular behavior has been investigated. It is found that there will be a meaningful region within which the elasto-plastic singular stress field becomes dominant under the large scale yielding condition. Therefore the fracture shall be evaluated by the elasto-plastic interfacial mechanics for such a case. The singularities determined numerically agree well with the theoretical results. It is also found that both the size of the yield zone and the stress distribution near the edge are dependent of the material combination. However, in the side of the material with smaller hardening exponent (the “harder” side), the theoretical singular stress field is not valid. Moreover, if the difference between two hardening exponents of the composed materials is very small, the displacement-matching method is no longer applicable. It is also found that the properties of the material with smaller hardening exponent mainly influence the angular stress distribution around the interface edge, but have very few effects on the singular stress order. It is also verified that the theoretical elastic solution of the singular stress field remains useful under the small scale yielding condition. Introduction Structures composed of bonded dissimilar materials have a wide application in engineering. To evaluate their strengths or reliabilities, the linear interfacial mechanics has been developed in the last decade [1]. However, for the cases such as ceramic/metal joints in which the yield strength of one composed material is relatively low, the elasto-plastic stress singular behavior [2-4] near the interface edge may have a strong effect on the strength. The evaluation approach based on the elasto-plastic interfacial mechanics is necessary. The authors [5] have theoretically deduced the elasto-plastic singular stress field near the interface edge of bonded linear hardening materials. It is found that the elasto-plastic stress singular behavior depends on not only the hardening coefficients, but also on the elastic properties. The elasto-plastic singular stress in this case can be determined by the two generalized Dundurs’ parameter and the geometry of the interface edge. The authors [6] have also proposed a method to determine the elasto-plastic stress singular order and the distribution near the interface edge of bonded dissimilar power-law hardening materials, based on the displacementmatching method [7,8] and two path-independent integrals. It is found that when the interface edge is degenerated to an interface crack, the results obtained by this method agree with that for an interface crack [7,8]. In this study, the elasto-plastic boundary element method (BEM) and finite element method (FEM) analyses have been carried out to investigate the elasto-plastic singular behaviors of bonded linear and power-law hardening materials, respectively. Based on the comparison of the numerical and the theoretical results, the validity and the applicable range of the theoretical solutions have been clarified. Interface edge of Bonded Linear Hardening Materials Theoretical Results Introducing the generalized Dundurs’ parameters as [5]

An Empirical Formula for Stress Intensity Coefficient of Orthogonal Bonded Materials Near Interface End

Logarithmic Singular Stress Field in an Interface Edge Consisting of Two Bonded Dissimilar Materials Subjected to a Concentrated Couple on Apex

Elasto-Plastic Singular Behavior at an Interface Edge

Stress Singularities on Three-Dimensional Interface Edge of Bonded Dissimilar Materials

Numerical methods for the determination of multiple stress singularities and related stress intensity coefficients

A Novel Method for Assessing Material Heterogeneity-Induced Interfacial Stress Singularities of Dissimilar Joints Under Normal Loading

Elastic-plastic boundary element analysis of interface edge in bonded dissimilar materials

Stress intensity factors of a surface crack near an interface end

An Empirical Formula for Stress Intensity Factors of Double Edge Half-Circular-Hole Cracks in A Rectangular Sheet in Tension

The Singular Stress Field and Stress Intensity Factors of A Crack Terminating at A Bimaterial Interface

A Method for Determining Elastic-Plastic Stress Singularity at the Interface Edge of Bonded Power Law Hardening Materials

Analysis of bi-material interface cracks with complex weighting functions and non-standard quadrature

A novel approach based on stress-impedance effect to assess the interfacial properties in fiber-reinforced composites

T-stress Evaluations of an Interface Crack in the Materials with Complex Interfaces

Investigation of Stress Intensity Factors for an Interface Crack in Multi-Interface Materials Using an Interaction Integral Method

Semi-empirical formulas on notch stress field and SIF of orthotropic V-shaped thin plate with initial crack under tensile-bending loads

T-Stress Evaluations For Nonhomogeneous Materials Using An Interaction Integral Method

WEIGHT FUNCTIONS FOR INTERFACE CRACKS IN DISSIMILAR ANISOTROPIC MATERIALS

Distributions of Residual Stresses in Diffusion Bonding of Dissimilar Materials Intermetallics Tial to Steel 40cr and Effect of Interlayer

A Cracked Sliding Interface Between Anisotropic Bimaterials

Stress Field Near an Interface Edge of Linear Hardening Materials