Abstract:D406A steel is commonly used to fabricate the shell of aerospace craft and therefore rigorous requirements have been set for welding quality of the steel. Laser welding has low heat input and small welding-induced residual deformation, while it is likely to incur defects such as undercut and insufficient reinforcement. A narrow-gap groove with the root face being 5 mm high was designed for the butt joints of D406A steel with the thickness of 6.6 mm. At first, the conventional bottom-up welding (scheme A) was adopted for laser welding. Serious pore defects are found in the weld, the reinforcement on the backside of the weld is small, and even surface depression is observed on backside of the weld. This is mainly because the height and volume of molten pool formed around the root face region during laser autogeneous welding is relatively small, so that metals in the molten pool are rapidly cooled, and the melt tend to flow upwards driven by the surface tension. Afterward, a new top-down welding process (scheme B) was proposed, that is, laser oscillating wire-filling welding in the upper groove at first and then high-power laser autogeneous welding penetrating the full thickness of steel sheets. Results show that the new welding scheme can effectively inhibit pores and depression of backside of the weld. The scheme improves the uniformity of weld metals, compositions, and microhardness along the thickness direction. The tensile strength of joints welded using the new scheme is 1,745 MPa after quenched-tempered heat treatments. The joints are fractured at the fusion zone (FZ), and the fracture is full of dimples. However, the joints show poor plasticity. The quenched and tempered Joint-B has an elongation of 3

Microstructures and Property of Butt Laser Joints of Aluminium Alloy 5A06 Sheets with Filler

Influence of Heat Input on the Performance of Joint with Filling Wire Laser Welding 5A06 Aluminum Alloy

Study on the Formation of Welding, Microstructure, and Properties of 5A06 Aluminum Alloy by Ultrasonic Laser-Assisted Filler Welding

Property Comparison of Laser Welded Butt Joint and T-joint of 6156-T4 Al Alloy

<p>Finite element simulation of tensile behavior of laser welded 5083 aluminum alloy joint with different filler wires</p>

Effect on the Property of 2195 Al-Li Alloy Laser-Welded Joints with Different Filler Materials

Solidification microstructures and softening behavior of laser welded 6082-A356 aluminum alloy dissimilar butt joints

Research on the Microstructures and Properties of AA5052 Laser-Welded Joints with the ER4043 Filler Wire

Double-sided Laser Beam Welded T-joints for Aluminum-Lithium Alloy Aircraft Fuselage Panels: Effects of Filler Elements on Microstructure and Mechanical Properties

Microstructure and Mechanical Properties in Friction Stir Welded 5A06 Aluminum Alloy Thick Plate

Microstructural Evolution and Mechanical Properties of Friction Stir Welded Butt Joints of 5A06 Alloy Ultra-Thin Sheets

Microstructure and mechanical properties of ADC12/6063-T6 aluminum alloy butt joint achieved by metal inert gas groove welding

Microstructural, Porosity and Mechanical Properties of Lap Joint Laser Welding for 5182 and 6061 Dissimilar Aluminum Alloys under Different Place Configurations

Study of the Microstructure and Properties of the Butt Joint of Laser-Welded Titanium Alloy with Flux-Cored Wire

Effect of Bevel Angle on Microstructure and Mechanical Property of Al/steel Butt Joint Using Laser Welding-Brazing Method

Increased Quality and Welding Efficiency of Laser Butt Welding of 2205/X65 Bimetallic Sheets with a Lagging MIG Arc

Laser Butt Welding of 6.6-Mm Thick D406A Ultrahigh Strength Steel: Part I—Porosity and Lower Surface Depression

Comparative Study of 5A06 Aluminum Alloy Welded Joints Obtained by Different Laser–Tungsten Inert Gas Hybrid Welding

The Microstructure and Mechanical Properties of Dual-Spot Laser Welded-Brazed Ti/Al Butt Joints with Different Groove Shapes

Microstructural and Mechanical Characterization of Aluminum-Lithium Alloy 2060 Welded by Fiber Laser

Influence of Welding Parameters on Weld Formation and Microstructure of Dual-Laser Beams Welded T-Joint of Aluminum Alloy