Abstract:This paper studies the effects of polyvinyl acetate-ethylene (VAE) based redispersible polymer powder (RPP) and polyvinyl acetate-vinyl versatate-ethylene (VVE) based RPP on the structural build-up of 3D printing cement paste within several hours of hydration. At the same time, two cases of the presence or absence of hydroxypropyl methylcellulose (HPMC) were considered. The build-up performance of cement paste was assessed by the hysteresis area, dynamic yield stress ratio, static yield stress, shear modulus and ultrasonic plus velocity from the dynamic shear test, static shear test and ultrasonic wave transmission test. In addition, the limit layer thickness and printing velocity were calculated by dynamic and static yield stresses to quantitatively characterize shape stability and printing efficiency of cement paste. Results indicate that both VAE with higher ethylene content (VAE1) and WE decrease the structural build-up rate of cement paste, independent of shear test modes. However, VAE with lower ethylene content (VAE2) increases the structural build-up rate of cement paste under dynamic shear test whereas decreases the growth rate of static yield stress. The dynamic yield stress ratio of cement paste containing 2% VAE2 is 0.57, which is 83.9% higher than that of pure cement paste. In addition, HPMC alters the effects of VAE2 on the structural build-up of cement paste. VAE1 and WE decrease the shape stability of cement pastes with and without HPMC, while VAE2 is beneficial to the shape stability of cement paste. Limit layer thicknesses of cement pastes with 4% VAE2 are 7.3 mm and 14 mm in the absence and presence of HPMC, which are about 3.0 and 5.8 times that of pure cement paste. In the absence of HPMC, WE decreases the limit printing velocity of cement paste in the first tens of minutes. VAE1 and VAE2 can improve the printing efficiency due to the increase of limit printing velocity in the first tens of minutes. In the presence of HPMC, only VAE2 significantly improves the limit printing velocity of cement paste. (C) 2020 Elsevier Ltd. All rights reserved.

Study on the retardation of re-dispersible polymer powders on cement hydration based on morphologies of Ca( OH) 2

BSE‐IA Reveals Retardation Mechanisms of Polymer Powders on Cement Hydration

Influence of Superplasticizer Type and Dosage on Early-age Drying Shrinkage of Cement Paste with Consideration of Pore Size Distribution and Water Loss

Characteristics of Hadley grains in hardened cement paste modified by redispersible polymer powders

Influences of PCE Superplasticizers with Varied Architectures on the Formation and Morphology of Calcium Hydroxide Crystals

Retardation effect of PCE superplasticizers with different architectures and their impacts on early strength of cement mortar

Influence of Recycled Cement Paste Powder on Early-Age Plastic Shrinkage and Cracking of Cement-Based Materials

Study on rheological, adsorption and hydration properties of cement slurries incorporated with EPEG-based polycarboxylate superplasticizers

An NMR Investigation of the Influence of Cation Content in Polymer Ion Retarder on Hydration of Oil Well Cement

Poly(carboxylated ether)s as Cement Additives: The Effect of the Addition Method on Hydration Kinetics

Rheological Properties and Early-Age Microstructure of Cement Pastes with Limestone Powder, Redispersible Polymer Powder and Cellulose Ether

Effects of the Charge Characteristics of Polycarboxylate Superplasticizers on the Adsorption and the Retardation in Cement Pastes

Surface Modification of Colloidal Polymer Particles and Its Effect on Cement Hydration

Redispersible Acrylic Ester Polymers: Effect of Polymer Property Changes Due to Polymerization Method Modification and Functional Additives on the Performance of Polymer Cement Mortar

Effect of polysaccharides on the hydration of cement paste at early ages

Effects of Redispersible Polymer Powders on the Structural Build-Up of 3D Printing Cement Paste with and Without Hydroxypropyl Methylcellulose

Retardation Effect of Styrene-Acrylate Copolymer Latexes on Cement Hydration

Quantitative Analysis of the Calcium Hydroxide Content of EVA-Modified Cement Paste Based on TG-DSC in a Dual Atmosphere

Effect of Surface Modification of Colloidal Particles in Polymer Latexes on Cement Hydration

Innovative Strategies for Time-Release PCE Design and Cement Paste Fluidity Control

Investigating the effect of polycarboxylate-ether based superplasticizer on the microstructure of cement paste during the setting process