Abstract:Thermal control of electronic components is a continuously emerging problem as power loads keep increasing. To solve these thermal problems impinging jets are generally used in engineering, science and industry for its good heat transfer performance. In this study; cooling of a flat plate under constant heat flux condition, inside a rectangular channel, consisting of one open and three blocked sides was experimentally and numerically investigated using a single air jet flow. The impingement surface was a copper plate of the same width as the jet nozzle. Inlet flow velocities were measured using a Laser Doppler Anemometer (LDA) system. Temperature measurements were performed using thermocouples. Local and mean Nu numbers were determined as a function of two parameters, (a) Jet-to-plate distance (H/Dh) in the range of 4–10 and (b) Reynolds number based on the hydraulic diameter of the slot nozzle in the range of 4000–10,000 (corresponding to an exit jet velocity from 6.5 to 16.2 m/s). Numerical investigation was also performed. Low Re number k–ε turbulence model was used during investigations. The results are presented in the form of graphs showing the variation of the local Nusselt number as a function of these parameters. The effect of Re number on local Nu number was examined for q″ = 1000 W/m2 and H/Dh = 6. In general, it was observed that heat transfer is sensitive to the Reynolds number and increases with increasing Re number. Average Nusselt number increases of 49.5 % from Re = 4000 to Re = 10000. Effect of H/Dh on heat transfer under impinging air jets was examined with local Nusselt numbers. Local Nusselt number was less sensitive to H/Dh in the range of H/Dh = 4–10. Average Nusselt number decreases of 17.9 % from H/Dh = 4 to H/Dh = 10. The highest average Nu number was achieved for Re = 10,000 and H/Dh = 4. The numerical results agreed well with the experimental data, including local and average Nusselt numbers. Correlations are proposed to predict the local Nusselt number as a function of Re number and H/Dh.

Experiment Study of Confined Jets Impingement onto a Target Plate With Pin Fins in a Narrow Channel

Jet Impingement Heat Transfer in Narrow Channels with Different Pin Fin Configurations on Target Surfaces

An Experimental Investigation Of Impingement Heat Transfer In Narrow Space With Full-Height Pin Fins

Numerical predictions of jet impingement heat transfer on square pin-fin roughened plates

Numerical Investigation of Impingement Heat Transfer on A Flat and Square Pin-Fin Roughened Plates

Jet impingement heat transfer performance in a double-wall cooling structure with film effusion holes and pin fins

On heat transfer and flow characteristics of jets impingement on a concave surface with varying pin-fin arrangements

Influences of Micro Pin-Fin on Jet Array Impingement Heat Transfer: Effects of Jet to Target Distance, Micro Pin-Fin Shapes, Height, and Reynolds Number

Flow and Heat Transfer Characteristics of Micro Pin-Fins under Jet Impingement Arrays

Multiple-jet impingement heat transfer in double-wall cooling structures with pin fins and effusion holes

Experimental and numerical study of heat transfer from a heated flat plate in a rectangular channel with an impinging air jet

Investigation of the roughened target plate to enhance the impingement heat transfer with reduced pressure loss

NUMERICAL INVESTIGATION OF CONFINED SINGLE JET IMPINGING ON A DIMPLED TARGET SURFACE USING Al2O3-WATER NANOFLUIDS

Experimental and Numerical Study of the Turbulent Flow and Heat Transfer in a Wedge-Shaped Channel with Guiding Pin Fin Arrays under Rotating Conditions

Numerical Study on Flow and Heat Transfer Characteristics of Pin-Fins with Different Shapes

Computational investigation of curvature effects on jet impingement heat transfer at internally cooled turbine vane leading edge regions

Heat Transfer and Flow Characteristics of the Jet Array Impingement

Effect of the Nozzle Geometry on Flow Field and Heat Transfer in Annular Jet Impingement

Numerical Study on Stagnation Point Heat Transfer by Jet Impingement in A Confined Narrow Gap

Modelling Of Impinging Flow And Heat Transfer In A Confined Narrow Gap

An Experimental Study Of Transitional Flow Friction And Heat Transfer Performance Of A Channel With Staggered Arrays Of Mini-Scale Short Pin Fins