Abstract:Poly (lactic acid) (PLA)-Poly (propylene carbonate) (PPC) block copolymer compatibilizers are produced in incompatible 70wt%PLA/PPC blend by initiating transesterification with addition of 1% of tetra butyl titanate (TBT) or by chain extension with addition of 2% of 2,4-toluene diisocyanate (TDI). The above blends can have much better mechanical properties than the blend without TBT and TDI. The elongation at break is dramatically larger (114% with 2% of TDI and 60% with 1% of TBT) than the blend without TDI and TBT, with a slightly lower mechanical strength. A small fraction of the copolymer is likely formed in the PLA/PPC blend with addition of TBT, and a significant amount of the copolymer can be made with addition of TDI. The copolymer produced with TDI has PPC as a major content (~70 wt%) and forms a miscible interphase with its own Tg. The crystallinity of the blend with TDI is significantly lower than the blend without TDI, as the PLA blocks of the copolymer in the interphase is hardly to crystallize. The average molecular weight increases significantly with addition of TDI, likely compensating the lower mechanical strength due to lower crystallinity. Material degradation can occur with addition of TBT, but it is very limited with 1% of TBT. However, compared with the blends without TBT, the PLA crystallinity of the blend with 1%TBT increases sharply during the cooling process, which likely compensates the loss of mechanical strength due to the slightly material degradation. The added TDI does not have any significant impact on PLA lamellar packing, but the addition of TBT can make PLA lamellar packing much less ordered, presumably resulted from much smaller PPC domains formed in the blend due to better compatibility.

Effect of Triphenyl Phosphite on the Properties of PLA/PBS Blend System

Properties and morphology of poly(lactic acid)/soy protein isolate blends

Toughness Enhancement of Poly(lactic Acid), Bamboo Particle and Ultrafine Bamboo-Char Ternary Biocomposites by Polyethylene Glycol Plasticization

Effects of Poly(ε-caprolactone) on the Properties of Poly (lactic acid)/Poly (butylene succinate) Blends

Research on Poly(lactic acid)/Poly(butylenes succinate) Blends

Preparation and Characterization of Poly(butylene Succinate-Co-adipate)/poly(lactic Acid) Blends with Enhanced Compatibility, Mechanical Properties, and Heat Resistance

Improvement of rheology and mechanical properties of PLA/PBS blends by in-situ UV-induced reactive extrusion

Effect of Styrene-Maleic Anhydride Copolymer on Properties of PBST/PLA Blends

Improvement of Mechanical Property for PLA/TPU Blend by Adding PLA-TPU Copolymers Prepared via In Situ Ring-Opening Polymerization

Study of Polylactic Acid/Liquid Polyisobutene Blends

Structure effect of phosphite on the chain extension in PLA

Rheology of Poly(lactic Acid)/poly(trimethylene Terephthalate) Blends Compatibilized by Clay or Maleic Anhydride-Grafted Poly(ethylene-Octene) Elastomer

Effects of Polybutylene Succinate Content on the Rheological Properties of Polylactic Acid/Polybutylene Succinate Blends and the Characteristics of Their Fibers

Toughening Modification of PLLA/PBS Blends Via in Situ Compatibilization

High Content of Thermoplastic Starch, Poly(butylenes Adipate-Co-terephthalate) and Poly(butylene Succinate) Ternary Blends with a Good Balance in Strength and Toughness.

Crystallization, Structure and Significantly Improved Mechanical Properties of PLA/PPC Blends Compatibilized with PLA-PPC Copolymers Produced by Reactions Initiated with TBT or TDI

Effect of Polybutylene Succinate Additive in Polylactic Acid Blend Fibers via a Melt-Blown Process

Effects of Trans-Esterification Stabilizers on Mechanical Properties and Structure of Poly(butylene Terephthalate)/polycarbonate Blends

Chain extension and oxidation stabilization of Triphenyl Phosphite (TPP) in PLA

Mechanical Properties and Thermal Behavior of TPS/PBS Blends with Maleated PBS As a Compatibilizer

Toughening Modification of Polylactic Acid by Thermoplastic Silicone Polyurethane Elastomer