Abstract:In recent decades, geoelectrical methods have played a very important role in near-surface investigation. The most widely used of these methods is electrical resistivity tomography (ERT). Regardless of the forward and inversion algorithms used, the original data collected from a survey is the most important factor for quality of the resulted model. However, 3D electrical resistivity survey design continues to be based on data sets recorded using one or more of the standard electrode arrays. There is a recognized need for the 3D survey design to get better resolution using fewer data. Choosing suitable data from the comprehensive data set is a great approach. By reasonable selecting, better resolution can be obtained with fewer electrodes and measurements than conventional arrays. Previous research has demonstrated that the optimized survey design using the 'Compare R' method can give a nice performance.This paper adds target-oriented selection and modified the original 'Compare R' method. The survey design should be focused on specific target areas, which need a priori information about the subsurface properties. We select electrodes and configurations as the target set by the comprehensive set firstly which meets the requirements of the target area. The number of measurements and electrodes is much less than the comprehensive set and the model resolution matrix takes less time to calculate. At the next step for rank, we calculate the sensitivity matrix of the target set only once and then calculate the contribution degree of each measurement separately from it. The time of iterative calculation of the resolution matrix when measurements set changing is less than the original method.The traditional method of evaluating RMS is not appropriate for comparing the quality of collected data by different survey designs. SSIM (structural similarity index) gives more reliable measures of image similarity better than the RMS. The curves of SSIM values in three dimensions and the average SSIM are given as quantitative comparisons. Besides, the frequency of electrodes utilized given to guides on selecting the highest used electrodes. Finally, the curves of the average relative resolution S and the number of electrodes as the number of measurements increase are given, which proves the method works effectively.The results show the significance of using target-oriented optimized survey design, as it selects fewer electrodes and arrays than the original CR method. Also, it produces better resolution than conventional arrays and takes less calculation time. 3D SSIM, frequency of electrodes used, the relationship between average relative resolution, number of electrodes and number of measurements, these quantitative comparison methods can effectively evaluate the data collected in various survey designs.

High Density Electrical Resistivity Inversion Based on Sequential Quadratic Programming Method

A FEASIBILITY STUDY OF RAPID TWO-DIMENSIONAL MT CURVE COMPARISON INVERSION

The inversion of apparent density based on the separation and continuation of potential field

Target-oriented Optimized Survey Design and Quantitative Comparison for 3D Electrical Resistivity Tomography

Elastic Impedance Inversion Based on Improved Particle Swarm Optimization

Three-Dimensional Inversion of Borehole-Surface Resistivity Method Based on the Unstructured Finite Element

Numerical modeling of 3D DC resistivity method in the mixed space-wavenumber domain

Three-Dimensional Anisotropic Inversion for Direct Current Resistivity Method Using Unstructured Tetrahedral Discretization

3D Forward and Inversion Problems of Borehole-to-Surface Electrical Method

Three-Dimensional Induced Polarization Parallel Inversion Using Nonlinear Conjugate Gradients Method

Three-Dimensional Soil Resistivity Inversion Using Patching Method.

Study on Inversion Methods for Travel Time Tomography Based on Generalized Inverse Theory

2.5D Inversion of Borehole Transient Electromagnetic Method with Scanning Detection Based on RCQPSO-LMO Combined Algorithm

3D modeling and inversion of the electrical resistivity tomography using steel cased boreholes as long electrodes

Quasi-2D inversion of surface large fixed-loop transient electromagnetic sounding data

An efficient three-dimensional (3D) inversion algorithm for recovering magnetic targets when remanence exists

The Application of the Supervised Descent Method in the Inversion of 3D Direct Current Resistivity Data

Application of the Equipotential Line Tracing Method to Cross-Hole Electrical Resistivity Tomography

Inversion of potential‐field data by iterative forward modeling in the wavenumber domain

Fictitious Point Technique Based on Finite-Difference Method for 2.5D Direct-Current Resistivity Forward Problem

3D transient electromagnetic inversion based on explicit finite-difference forward modeling