Abstract:OBJECTIVE:To construct a dynamic knee joint finite element model based on CT image data and verify the validity of the model. To provide a simulation model and basic data for biomechanical research of the knee joint by further finite element analysis. METHODS:The CT data of a healthy male knee joint was selected. With the help of Mimics 19.0 and Hypermesh 12.0 software, a high simulation finite element model of knee joint was established following steps, including geometric reconstruction, reverse engineering, meshing and material characterization. The dynamic knee flexion model was generated by determining the boundary conditions and torque loading, and the validity of themodel was confirmed. The biomechanical changes of the tibiofemoral and patellofemoral joints under different knee flexion angles were analyzed by applying the loads (500 N) to the finite element model during knee flexion. RESULTS:A finite element model of knee joint was established based on CT images and anatomical characteristics. The model included three-dimensional elements such as bone, ligament, cartilage, meniscus and patellar retinaculum. The different finite element models of knee flexion states were produced by applying different torques after establishing boundary conditions. According to equivalent conditions (knee flexion 30 degrees, quadriceps tendon under 200 N stretch), the peak stress value of patella was 2.209 MPa and the average Mises stress was 1.132 MPa; the peak stress value of femoral trochlear was 1.405 MPa and the average Mises stress was 0.936 MPa. The validity of the model was proved by the difference between the model and previous studies of 1% to 13.5%. Dynamic model loading showed that the Mises stressof tibiofemoral joint decreased with the increase of knee flexion angle, while the Mises stress of patellofemoral joint was positively correlated with knee flexion angle. The Mises stress of cartilage stress planes at different knee flexion angles was significantly different(P<0.05). CONCLUSION:The finite element model established in this study is more comprehensive and can effectively simulate the biomechanical characteristics of dynamic knee joint, which provides support for further simulation mechanics researches of the knee joint.

Three-dimensional reconstruction of subject-specific dynamic patella of femoral joint using static magnetic resonance based methodology

Reconstruction and application of three-dimensional quasi-dynamic motion model of patellofemoral joint

In Vivo Measurements of Patellar Tracking and Finite Helical Axis Using a Static Magnetic Resonance Based Methodology

Reconstruction and Optimization of the 3D Geometric Anatomy Structure Model for Subject-Specific Human Knee Joint Based on CT and MRI Images

Three-dimensional Reconstruction of Subject-Specific Knee Joint Using Computed Tomography and Magnetic Resonance Imaging Image Data Fusions.

Tibial meniscal dynamics using three-dimensional reconstruction of magnetic resonance images

A Method for Accurate Reconstruction of Subject-Specific Anatomical Finite Element Model of Knee Joint

Relationship Between Patellofemoral Finite Helical Axis and Femoral Trans-Epicondylar Axis Using a Static Magnetic Resonance-Based Methodology

A Method of Vivo Human Knee Joint 3D Model Reconstruction Based on MR Images

Using Virtual Markers To Explore Kinematics Of Articular Bearing Surfaces Of Knee Joints

Dynamics analysis of the anterior cruciate ligament reconstruction surgery based on magnetic resonance imaging

A Three-Dimensional Finite Element Model Constructed Using Magnetic Resonance Images of a Knee

Constrained Statistical Modelling of Knee Flexion from Multi-Pose Magnetic Resonance Imaging

[Construction and simulation mechanical analysis of dynamic knee joint finite element model based on CT image].

In vivo biomechanical dynamic simulation of a healthy knee during the single-leg lunge and its experiment validation

Measurement of Quasi-Static 3-D Knee Joint Movement Based on the Registration From CT to US

An Initial Study of Tracking Movement of Normal Patellar Using Volume Scan on Sensation 320 CT

Femoral valgus angle measurement in Three-dimensional reconstruction Virtual environment based on CT images

Time-Resolved Quantification of Patellofemoral Cartilage Deformation in Response to Loading and Unloading via Dynamic MRI With Prospective Motion Correction

Accurate Three-Dimensional Registration of Magnetic Resonance Images for Detecting Local Changes in Cartilage Thickness.

A preliminary report of fast establishment of three-dimensional digital models of anterior cruciate ligament based on MRI