Abstract:Background Traumatic coronoid deficiency with persistent elbow instability is a challenging condition. Autologous bone graft reconstruction is often associated with a range of additional clinical problems and the outcome is often unpredictable. The purpose of this study was to design a prosthetic device that can reconstruct coronoid deficiency of any height and to evaluate its mechanical properties using finite element analysis. Materials and Methods A customized coronoid prosthesis was designed based on image registration, automatic measurement and computer-aided design. After pilot study and sample size calculation, image data collected from six patients who underwent bilateral complete upper extremity CT scans were reconstructed. The test was divided into three groups: coronoid intact, prosthesis and autograft. Regan-Morrey type II and autologous olecranon osteotomy models were established. The prosthesis and autogenous olecranon were assembled to the coronoid base. Stress was applied axially along the proximal humeral diaphysis and implant micromotion and contact mechanics of the humeroulnar joint were measured at 30°, 45°, 60° and 90° of joint flexion respectively. Results At all flexion angles, the maximum stress on the coronoid articular surface was significantly reduced in the prosthesis and autograft groups, with the reduction being more significant in the latter ( P < 0.001). With increasing flexion, the maximum stress at the coronoid articular surface increased significantly after autograft reconstruction (7.2 to 68 MPa, P < 0.001), whereas the humeroulnar joint obtained a similar contact mechanics pattern to that of the control group after prosthetic reconstruction. As the flexion angle increased, the relative micromotion of both the prosthesis and autograft increased significantly (0.5-1.6 vs 0.2-1.2, P measure time < 0.001, P groups < 0.001). Contact pressure and center-of-force paths of the humeroulnar joint experience abrupt stress changes at approximately 60° of flexion. Conclusion The contact stress pattern in the humeroulnar joint is similar in prosthesis and intact coronoid groups. Autograft reconstruction increases contact stresses at the articular surface and alters the joint center-of-force path. The "stress surge phenomenon" in the humeroulnar joint surface before and after 60° of flexion may be one of the mechanisms of traumatic elbow degeneration.

Anatomical Reconstruction of Severe Bone Defect in the Humeral Condyle:A long-term Follow-up

Surgical treatment of intercondylar fractures of humerus

Anatomic Plate Fixation Plus One Stage Bone Grafting for Treatment of Complex Bone Fractures of Terminal Femora

Onlay cortical struct allograft in revision arthroplasty of the femoral component

[Reconstruction of Bone Defects with Autograft after Resection of Upper Extremity Bone].

[Bone-cartilage transfer for osteochondritis dissecans of the humeral capitellum]

Photoimaging of self-organized CaCO3/polymer hybrid films by formation of regular relief and flat surface morphologies.

Clinical Outcomes of Operations in Humeral Intercondylar Fractures

Different fixation methods for artificial femoral head replacement: A biomechanical comparison of joint stability

The Common Bile Duct: Significance of Its Diameter

A case report of membrane induction combined with RIA technique for the repair of distal humerus segmentary bone defect

Surgical treatment ofproximal humeral fractures

Short and long term follow up of humeral condylar fracture type II treated by lag screw and anti-rotational pin associated to olecranon osteotomy

Treating Intereondylar Comminuted Fracture of Humerus by Olecranon Osteotomy and Y-Shape Internal Fixation with Steel Plate

[Three cases with blue rubber bleb nevus of children and review of the literature].

Salvage Treatment for a Periprosthetic Humeral Nonunion: A Case Report

Finite element analysis of a customized coronoid prosthesis for traumatic coronoid deficiency

[Clinical Outcomes of Total Elbow Replacement in the Treatment of Complex Distal Humeral Fractures].

Novel application of 3D printed microporous prosthesis to repair humeral nonunion with segmental bone defects: a case report

Anconeus Muscle-Pedicle Bone Graft With Periosteal Coverage for Osteochondritis Dissecans of the Humeral Capitellum

Unicondylar osteoarticular allografts of the knee