Abstract:<p>The aim of the present paper is to evaluate the effect of Lode angle incorporation into a fracture criterion when predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes through finite element (FE) simulations. To this end ballistic tests in the sub-ordnance impact velocity range were firstly conducted on 9.94 mm thick 2024-T351 aluminum alloy plates using cylindrical projectiles with blunt, hemispherical and ogival nose shapes, a nominal diameter of 12.66 mm, and a nominal mass of 50 g. Ballistic limit velocities (BLVs) for different projectile-target pairs considered were calculated using initial vs. residual velocity data obtained in the experiments. Subsequently FE simulations of the conducted experiments were performed with SIMULIA Abaqus software. In those simulations Johnson-Cook yield criterion with a modified strain hardening law was accompanied with either the Lode-independent Johnson-Cook (JC) fracture criterion or the Lode-dependent modified Mohr-Coulomb (MMC) fracture criterion to describe target material properties. Finally, the predicted ballistic resistance and fracture patterns of the targets were compared with those observed in the experiments. It was found that in the simulations with the Lode-independent JC fracture criterion the BLVs of the targets were overestimated by 18.0-35.1% depending on the projectile nose shape. In the simulations with MMC fracture criterion the BLVs predictions were substantially improved, so that the difference with the experimental results did not exceed 9.0%. Targets failure mechanisms obtained in the simulations with MMC fracture criterion also better match the experiments than those predicted with JC fracture criterion. In the simulations with MMC fracture criterion the targets impacted by the projectiles with blunt and hemispherical noses failed through shear plugging, whereas ogive-nosed projectiles caused ductile hole enlargement and target fragmentation due to its rear side radial fracture and bending of formed short petals with their eventual shear fracture. At the same time the simulations with JC fracture criterion predicted shear plugging for the blunt-nosed projectiles, very small conical plug ejection and target fragmentation due to discing for the hemispherical-nosed projectiles, and ductile hole enlargement for the ogive-nosed projectiles. A detailed analysis of the failure process revealed that in the case of the ogive-nosed and hemispherical-nosed projectiles, respectively, the ductile hole enlargement occurs during the initial stage of the impact and subsequent through-thickness fracture develops causing either fragmentation of the target or its shear plugging failure. The Lode-independent JC fracture criterion overestimates a material fracture strain under shear, thus leading to poor prediction of 2024-T351 aluminum alloy targets ballistic performance in the numerical simulations.</p>

Application of Lode dependent fracture criterion in predicting fracture of 6061-T6511H aluminium alloy Taylor rods

Effect of the Lode parameter in predicting shear cracking of 2024-T351 aluminum alloy Taylor rods

Dynamic Mechanical Properties and Modification of Fracture Criteria of 6061-T651 Aluminum Alloy

Development of an Improved MMC-based Fracture Criterion Characterizing the Anisotropic and Strain Rate-Dependent Behavior of 6061-T5 Aluminum Alloy

Experimental and numerical investigation on plasticity and fracture behaviors of aluminum alloy 6061-T6 extrusions

Effect of Lode angle incorporation into a fracture criterion in predicting the ballistic resistance of 2024-T351 aluminum alloy plates struck by cylindrical projectiles with different nose shapes

Simulation of Ductile Fracture in an Aluminum Alloy Using Various Criteria

Development of a Modified Gurson–Tvergaard–Needleman Damage Model Characterizing the Strain-Rate-Dependent Behavior of 6061-T5 Aluminum Alloy

Experimental and numerical investigations into the ductile fracture during the forming of flat-rolled 5083-O aluminum alloy sheet

Effect of stress triaxiality and normalized Lode angle on ductile fracture of aluminum 2139-T8

Study of dynamic mechanical behavior of 1060-H112 aluminum alloy: Experimental and numerical simulation

The experimental and numerical study of AA6061-T6 aluminum alloy under repeated impacts

Linear Transformation Based Orthotropic Shear Ductile Fracture Criterion for Lightweight Metals

Application of the modified Mohr–Coulomb fracture criterion in predicting the ballistic resistance of 2024-T351 aluminum alloy plates impacted by blunt projectiles

Numerical simulation of fracture in Taylor rod impact problem with stochastically distributed inherent damage

Assessment of Newly Developed Ductile Fracture Criteria for Lightweight Metals

Characterization and prediction of fracture in 6000- and 7000-series aluminum alloy sheet under various stress states

A New Ductile Fracture Criterion Considering Both Shear and Tension Mechanisms on Void Coalescence

Numerical and Experimental Fracture Study for 7003 Aluminum Alloy at Different Triaxialities

A Stress-Based Shear Fracture Criterion Considering the Effect of Stress Triaxiality and Lode Parameter

Finite Element Modeling for Orthogonal Machining of AA2024-T351 Alloy with an Advanced Fracture Criterion