Abstract:5A06 aluminum alloy bar was brazed by temperature gradient transient liquid phase diffusion welding (TG-TLP). The effects of brazing temperature on the microstructure and the tensile strength of the brazing joints were investigated. Three typical brazing filler alloys (1# Al-20Cu-6Si-2Ni, 2# Al-10Cu-10Si-3Mg-1Ga, and 3# Al-6Cu-10Si-2Mg-10Zn) were prepared by smelting, and TG-TLP diffusion bonding was carried out at different brazing temperatures (550 °C~590 °C). The results show that with the increase in brazing temperature, the oxide films at the brazing junction are easier to be broken and dispersed, but the oxidation extent will also increase. The oxidation products enriched were mainly Al2O3 and SiO2 at the brazing junction. There are different optimal brazing temperatures corresponding to the different filler alloys. For 1#, the optimal temperature is 570 °C; for 2# is 580 °C; for 3# is 580 °C. For 1# brazing joints, the maximum tensile strength was 113 MPa, and for 2# was 122.4 MPa. Under the experimental conditions of this study, the maximum tensile strength of the TG-TLP joint is 147.4 MPa of 3# brazing sample (at 580 °C), which has increased by 30% and 20% compared to 1# and 2# respectively. The nickel-rich phase at the interface (of 1# brazing filler) could form a brittle fracture, which was unfavorable for interface bonding. For TG-TLP brazing of 5A06, the filler alloy with high Al:Cu ratio (12:1 wt.%) needs a sufficient temperature gradient to exert the film-breaking effect, while the filler alloy with low Al:Cu ratio (3.6:1 wt.%) needs to accurately control its brazing temperature to avoid excessive oxidation. There are many research gaps in the influence of brazing material composition and brazing temperature on the microstructure and mechanical properties of 5A06 aluminum alloy TG-TLP joints. The research results can provide a theoretical basis for formulating the TG-TLP brazing specification of 5A06 aluminum alloy.

Effects of Welding Temperature on Microstructure and Tensile Properties of Pressure Welded Joint between Hot Dip Galvanized Steel and Aluminum Alloy

Effect of Heat Input on the Microstructure and Mechanical Properties of 6060 Aluminum Alloy/Galvanized STEEL MIG Welding–Brazing Joints

Effect of Heat Distribution on Microstructure and Mechanical Properties of Electron Beam Welded Dissimilar TiAl/TC4 Joint

Interface Microstructure and Mechanical Property of CMT Welding-Brazed Joint Between Aluminum and Galvanized Steel Sheet

Effect of Welding Defects on Mechanical Properties of Welded Joints Subjected to Temperature

Effect Of Heat Treatment On The Microstructure And Properties Of A Ti3al Linear Friction Welding Joint

Effect of Heat Treatment on the Microstructure and Properties of a Ti<sub>3</sub>Al Linear Friction Welding Joint

Effect of Post-Weld Heat Treatment on Microstructure and Properties of Al-Mg Alloy Welded Joints

Effects of electron beam welding parameters on the microstructure of titanium to aluminum alloy joints

Study on the Morphology, Microstructure, and Properties of 6082-T6 Aluminum Alloy Joints in MIG Welding

TEM Microstructure, Mechanical Properties and Temperature Estimation in the 5XXX Series Al-Mg-Si Aluminum Alloy with W-Ni-Fe Tungsten Composite Friction-Welded Joints

Investigation on Temperature Field and Interfacial Microstructure of Ti/Al Arc Welding-Brazing Joint

Influence of alloy elements on microstructure and mechanical property of aluminum–steel lap joint made by gas metal arc welding

Microstructure and Mechanical Properties of Aluminum/Stainless Steel Joints Welded by Different Weld Heat Input

Effect of Heat Input on Microstructure and Mechanical Properties of Ti/Cu66V34/Cu Joints by Electron Beam Welding

Effect of Brazing Temperature on Microstructure, Tensile Strength, and Oxide Film-Breaking Synergy of 5A06 Aluminum Alloy Welded by TG-TLP

Effect of Annealing Temperature on Microstructure and Properties of Al/Mg Magnetic Pulse Welding Joints

Effect of heat input on mechanical properties of electron beam welded joint of TiAl based alloy

Research on Effect of Welding Ways on Joint Performance of Aluminum Alloy

Effect of Heat Input on the Microstructures and Mechanical Properties of Laser Welded Ti2AlNb Alloys

Evolution of Microstructure and Mechanical Properties of a Dissimilar Aluminium Alloy Weldment