Abstract:Abstract In deep underground mining, achieving stable support for roadways along with long service life is critical and the complex geological environment at such depths frequently presents a major challenge. Owing to the coupling action of multiple factors such as deep high stress, adjacent faults, cross-layer design, weak lithology, broken surrounding rock, variable cross-sections, wide sections up to 9.9 m, and clusters of nearby chambers, there was severe deformation and breakdown in the No. 10 intersection of the roadway of large-scale variable cross-section at the − 760 m level in the Nanfeng working area of the Wuyang Coal Mine. As there are insufficient examples in engineering methods pertaining to the geological environment described above, the numerical calculation model was oversimplified and support theory underdeveloped; therefore, it is imperative to develop an effective support system for the stability and sustenance of deep roadways. In this study, a quantitative analysis of the geological environment of the roadway through field observations, borehole peeking, and ground stress testing is carried out to establish the FLAC 3D variable cross-section crossing roadway model. This model is combined with the strain softening constitutive (surrounding rock) and Mohr-Coulomb constitutive (other deep rock formations) models to construct a compression arch mechanical model for deep soft rock, based on the quadratic parabolic Mohr criterion. An integrated control technology of bolting and grouting that is mainly composed of a high-strength hollow grouting cable bolt equipped with modified cement grouting materials and a high-elongation cable bolt is developed by analyzing the strengthening properties of the surrounding rock before and after bolting, based on the Heok-Brown criterion. As a result of on-site practice, the following conclusions are drawn: (1) The plastic zone of the roof of the cross roadway is approximately 6 m deep in this environment, the tectonic stress is nearly 30 MPa, and the surrounding rock is severely fractured. (2) The deformation of the roadway progressively increases from small to large cross-sections, almost doubling at the largest cross-section. The plastic zone is concentrated at the top plate and shoulder and decreases progressively from the two sides to the bottom corner. The range of stress concentration at the sides of the intersection roadway close to the passageway is wider and higher. (3) The 7 m-thick reinforced compression arch constructed under the strengthening support scheme has a bearing capacity enhanced by 1.8 to 2.3 times and increase in thickness of the bearing structure by 1.76 times as compared to the original scheme. (4) The increase in the mechanical parameters c and φ of the surrounding rock after anchoring causes a significant increase in σ c and σ t ; the pulling force of the cable bolt beneath the new grouting material is more than twice that of ordinary cement grout, and according to the test, the supporting stress field shows that the 7.24 m surrounding rock is compacted and strengthened in addition to providing a strong foundation for the bolt (cable). On-site monitoring shows that the 60-day convergence is less than 30 mm, indicating that the stability control of the roadway is successful.

The analysis on the spewing failure in the project taking lead pipe grouting to go through the fault

Influences of grouting heave on overlying structures in shield tunneling

Introduction of Construction Process in Shenjiamen Immerse Tube Tunnel and Problem Analysis of Grouting

Study on the Stress and Deformation of Surrounding Rock and Support Structure of Super Large Section Tunnels Based on Different Excavation Methods

Numerical Simulation of Surrounding Rock Deformation and Grouting Reinforcement of Cross-Fault Tunnel under Different Excavation Methods

Advanced Grouting Model and Influencing Factors Analysis of Tunnels with High Stress and Broken Surrounding Rock

Numerical and practical investigation of the multiple hole grouting repair law of underground drainage pipeline defects

Highway tunnel crossing fault zones with water-rich highly weathered granite

Investigating the impacts of reinforcement range and grouting timing on grouting reinforcement effectiveness for tunnels in fault rupture zones using a numerical manifold method

Research on Seepage of Jointed Rock Mass of Tunnel and Limited Discharge of Grouting

Tunnel Lining Segment Deformation and Cracking Mechanisms during Tunneling in Complex Mixed Grounds with the Combined Mining and Shield Tunneling Method

Failure mechanism analysis for tunnel construction crossing the water-rich dense fracture zones: A case study

Deformation and failure analysis of surrounding rock mass in deep buried tunnels subjected to excavation

Study of Tunnel Damage Caused by Underground Mining Deformation: Calculation, Analysis, and Reinforcement

Research on grouting reinforcement technology of fault crossing roadway in fully mechanized mining face with large dip angle

Failure Mechanism of Grouted Floor with Confined Aquifer Based on Mining-Induced Data

Failure Analysis of Intersections of Large-Scale Variable Cross-Section Roadways in Deep Soft Rock and Study of Integrated Control Technology of Bolting and Grouting

Grouting Mechanism in Water-Bearing Fractured Rock Based on Two-Phase Flow

Experimental Study on Grouting Reinforcement Mechanism of Heterogeneous Fractured Rock and Soil Mass

Rock Strata Failure Behavior of Deep Ordovician Limestone Aquifer and Multi-level Control Technology of Water Inrush Based on Microseismic Monitoring and Numerical Methods

Refined analysis on compensation grouting performance via discrete element method