Development of Performance Test System for Oil Pump in Automobile Engine

WANG Haifeng,HU Dejin,XU Liming,RUAN Zhen,RAN Lihong

DOI: https://doi.org/10.3969/j.issn.1005-2402.2005.10.030

2005-01-01

Abstract:In this paper, the design requirement for the system and the soft hardware design are discussed in de-tail. The operation results showthat the system works steadily, and promotes the quality detection anddesign for newpumps actively.

What problem does this paper attempt to address?

Design for ABS piston pump test system

CAO Hui-fa,TAO Guo-liang,ZHOU Wen-yi

DOI: https://doi.org/10.3969/j.issn.1008-0813.2005.02.011

2005-01-01

Abstract:The development of ABS piston pump test system is described in this paper. The system is a speedy, accurate and safe on-line test system and can test the performances of ABS piston pump automatically.
The Development of the Static and Dynamic Performance Integrated Test System for Electro-hydraulic Servo Valve

WANG Xuanyin,SUN He,LI Xiaoxiao,LI Fushang

DOI: https://doi.org/10.3969/j.issn.1001-3881.2010.20.013

2010-01-01

Abstract:A static and dynamic performance integrated test system was designed based on virtual instrument technology to meet the needs of performance testing for electro-hydraulic servo valves used in power plant.The control principles and hydraulic circuit of the system were described.The compositions of hardware and software were introduced as well as the performance parameters.Com-paring the result of delivery test with the measured results,it proves that the system is available.The system has been used in practice.
Development And Simulation Of Lubrication Test System For Port Plate/Cylinder Block In Axial Piston Pump

QingLin Ai,Hua Zhou,Huayong Yang

DOI: https://doi.org/10.3321/j.issn:0253-9993.2004.06.021

2005-01-01

Abstract:ne composition and schematic of the lubrication test system for port plate/cylinder block friction pair in axial piston pump is described. The subsystem and functions of the test system are introduced. The lubrication characteristics of port plate/cylinder block such as film thickness, bearing support capability and leakage can be measured. And the influence of working pressure, temperature, rotating speed and structure on the lubrication can be tested as well. The measurement error is guaranteed to be less than 1 mu m by the high-accuracy electric eddy displacement sensors. The thickness of micron dimension lubricating film is feedback controlled with PID algorithm. The precise displacement feedback control system is simulated in dynamic with SIMULINK tool of MATLAB software, and it is significant to select the value of V-0/beta(e) K-ce and PID for the design of precise displacement feedback control system.
Automatic Control System for a Torque Converter Static and Cycle Hydraulic Tester

DAI Zhen-yu,XUAN Hai-jun,HONG Wei-rong,WU Rong-ren

DOI: https://doi.org/10.3969/j.issn.1002-2333.2007.07.060

2007-01-01

Abstract:To meet the development of the auto-industry,to facilitate different types of Hydraulic torque converter manufacturing and to test production quality,according to the principle of universal applicability,developing auto-control system of a torque converter static and cycle hydraulic tester based on Delphi.Such as multithreading and database.Simulation of the actual conditions of oil-pressure of the Hydraulic torque converter,testing the deformation of Static pressure-expansion and its Cycle-Endurance for the type of YJH300B-1,and we quite satisfied with the results.
Development of Experiment Rig for Lubricate Film of the Slipper-pad in Axial Piston Pumps

Qian-wei ZHUANG,Hua ZHOU,Qing-lin AI

DOI: https://doi.org/10.3969/j.issn.1001-3881.2005.03.044

2005-01-01

Abstract:The function,system composition,construction and test principle of a experiment rig were introduced,which were design for lubricate film of the slipper-pad in axial piston pumps.It can suit for transmitter of both oil and water,can do measure research for slipper-pad’s oil film of heavy pressure high speed large capacity,and can make experiment study in various simulation work condition.
Comprehensive Performance Measurement for Closed-circuit Variable Displacement Pump

LI Shuai,WEI Jian-hua

DOI: https://doi.org/10.3969/j.issn.1672-8904.2009.03.010

2009-01-01

Abstract:The measurement of closed-circuit variable displacement pump comprehensive performance is an important means to develop new product and guarantee product quality.Based on requirement analysis,an automatic measurement system of comprehensive performance for variable displacement pump was designed and implemented.A closed-circuit is used for variable displacement pump comprehensive performance test.A variety of sensors are used to collect running information data automatically during the testing process.Virtual instrument technique is adopted to realize data processing,analysis,management and measurement process automation.As actual production measurement results showed,the comprehensive performance measurement system has improved test efficiency and precision of experiment course and the intelligent level of the test system.
Development of Diesel Pump Performance Test System

Zhenhua Jin,Kaisheng Huang,Qingchun Lu,Shengfang Nie

DOI: https://doi.org/10.3321/j.issn:1004-132X.2006.17.024

2006-01-01

Abstract:To meet the requirements of diesel pump research and development, pump performance test system was developed. The system was designed based on virtual instrument architecture. Hardware consisted of IPC, signal conditional unit and high speed data acquisition card, software was developed with virtual instrument development workbench LabVIEW. Optic electric encoder output was taken as start position signal and scan clock. Function of multi channel angel based sampling, continuous multi cycle data acquisition and data processing were realized. Test in practice shows the system works well.
Design and Simulation Study of a Vacuum-pumping Deaerating Device for Hydraulic Oil

CHEN Chao,GONG Guo-fang,JIN Yao-lan,WANG Jing

DOI: https://doi.org/10.3969/j.issn.1000-4858.2008.02.029

2007-01-01

Abstract:A vacuum-pumping deaerating device for hydraulic oil was designed.This device is based on the Henrys law.It can improve the bulk modulus of hydraulic oil and ameliorate the transmission rigidity and precision of hydraulic system.Simulation study of balancing the pressure of oil tank was carried out using the simulator of AMESim.The results show that the piston pressure accumulator in this device plays a role in stabling tank pressure and absorbing the pressure pulsations availably.
Power Recovery Intelligent Testing System for Hydraulic Motor

WANG Xuan-yin,DAI Jie,PI Yang-jun,SUN He,YE Shui-huan

DOI: https://doi.org/10.3969/j.issn.1008-0813.2011.05.011

2011-01-01

Abstract:With regard to the needs of testing system for hydraulic motor used in business,an intelligent testing system was designed and put into use,which can test the status and indicators of the hydraulic motor,based on power recovery theory.It describes the hydraulic circuit and control principles of the system,and introduces the composition of hardware and software.It explains the issues including the power recovery,low-speed loading and intelligent control.Based on the delivery test,which compare the motor's actual performance,it proves that the system is available.
A Study on the Noise and Vibration Testing System for Automotive Final Drive

SHE Tu-bin,YANG Xu-jian,ZHOU Xiao-jun

DOI: https://doi.org/10.3969/j.issn.1001-4551.2006.01.013

2006-01-01

Abstract:Aiming at the performance of automotive final drive,this article introduces a computer-based testing system.The system can provide overall detecting and testing on performance indicators including the noise and vibration.Also the principle of testing and the design scheme of the software and hardware are explained,and the initial analysis on noise and vibration are presented.
Design and Implementation of Testing Device for Damping Oil Bulk Modulus and Fatigue Characteristic

JIANG Qiang,ZHANG Dawei

DOI: https://doi.org/10.3969/j.issn.1003-1251.2012.02.005

2012-01-01

Abstract:Hydraulic oil bulk modulus and fatigue property parameters are very important physical parameters in the hydraulic system,directly affects the stability and dynamic quality of the system.Based on the definition of the elastic modulus,the testing device for damping oil bulk modulus and fatigue characteristic has been designed,while using the oil gas suspension device of special purpose vehicle asthe testing object,where the fatigue characteristic parameters of hydraulic damping oil have been tested,such as temperature,viscosity.And the design of control system and data acquisition system are completed,timely communication with the host computer,the automatization of the test process is realized.
An Automatic Testing System for Vehicle's Drive Axis Performance Test

林军,周晓军,陈子辰,陈庆春

DOI: https://doi.org/10.3969/j.issn.1001-2257.2000.04.007

2000-01-01

Abstract:Introduces an new integrated electrohudromechanical and signal processing testing system for vehicle's drive axis performance test. With the test system , automatic braking performance testing will be possible on the condition of vehicle real working simulation during testing. Table and graph of the test demanded by customer are automatically completed.Mechanical property and degree of automation of the system can reach requirement for design in practical operation .
Automatic Testing and Control System for Electro-Hydraulic Proportional Displacement Pump Based on LabVIEW

陆倩倩,魏建华,赖振宇

DOI: https://doi.org/10.3969/j.issn.1004-1699.2009.04.005

2009-01-01

Abstract:An automatic testing and control system for electo-hydraulic proportional displacement pump with computer aided test is designed and developed, including sensor technology, programmable logic controller, industry PC and virtual instrument. The precision of all parameters is assured by speed, pressure and flow closed loop. By using virtual instrument technology, the testing of the over-all properties including static and dynamic characteristics of the electo-hydraulic proportional displacement pump is realized, mainly comprising fundamental performance test, pressure and flow control hysteresis test as well as pressure and flow response test. It turns out to be a higher accurate and efficient test system in practice. During the test, an abnormal output can be detected immediately, at the same time self protection is carried out.
Intelligent Test Machine for Whole Performance Testing on Lube Pump

Shi Lun,Hu Dejin,Xu Liming,Wang Haifeng

DOI: https://doi.org/10.3321/j.issn:0254-3087.2004.z1.110

2004-01-01

Abstract:The intelligent test machine for whole performance experiments on lube pump is controlled by industrial computer and PLC. The self-diagnosis and alarms for the machine troubles are developed. The mechanical structure and the control system structure are introduced briefly. Pump experiments, such as rotation performance experiment,on the machine have been done and the testing results are shown.
Hydraulic Pump Performance Test System Based on CAT Technology

Han-bin LIU,Bing XU,Wei LIU,Jun-hui ZHANG

DOI: https://doi.org/10.3969/j.issn.1005-2895.2010.05.022

2010-01-01

Abstract:In order to assess the performance of hydraulic pumps accurately,provide guidance for optimizing the structure,improve the technological level and upgrade products,the paper designed the hydraulic pump performance test system based on the CAT(Computer Aided Testing) technology.First,by designing the hydraulic principle and selecting components of the driving system,overload system and step-load system,then completed the integral hydraulic principle design of the hydraulic system.By using LabVIEW software and industrial computer,PLC,data acquisition cards as well as various types of sensors to design the software and hardware of the CAT system.The efficiency curves of the testing pump proved that the pump performance test system is reasonable.The application on the hydraulic pump performance test system of CAT technology has improved the automation and intelligent level of the test process as well as the test efficiency and accuracy.
R & D of an Automatic Testing System for Overall Performance of New Types of Motors

Huifen Lu,Di Lu,Ruofan Shen,Yuehua Xu,Jianyong Zhao

DOI: https://doi.org/10.3969/j.issn.1000-3886.2016.03.028

2016-01-01

Abstract:This paper introduces an integration of WT1 600 digital wattmeter and JN338A torque transducer in a system for testing overall performance of new types of motors,which can measure their characteristic parameters such as voltage,current,torque,speed and power.This testing system combines effectively hardware such as IPC,signal collecting card and sensor and application programs such as those for data collection and analysis,and user graphic interface,so as to perform good automatic measurement of the data on the characteristic points of new types of motors such as input and output parameters,and improve the testing efficiency and accuracy. Application results indicate easy operation,and safety and reliability of the testing system developed.It has the potential for engineering application as it satisfies the requirements on the testing of new types of motors.The system has been successfully applied on the platform of motor and electrical appliances of the Electrical College of Zhejiang University.
Oil Radiator's Integrative Test Control System Based on Microcontroller Unit

WANG Xue-feng,WANG Yun,QI Fang,XIA Li-feng

DOI: https://doi.org/10.3969/j.issn.1002-6886.2007.05.002

2007-01-01

Abstract:An automobile engine oil radiator's integrative test system(ORITS) has been developed and is introduced in this paper.Mechanical characteristic tests for the oil radiator product such as pressure cycle,static pressure resistance test and leak test can be performed automatically on this test-bed in terms of the ORITS.The ORITS system has adopted the embedded control technology,hydraulic system CAT(Computer Aided Testing) technology,and virtual instrument technology to assure its design targets: operation stability,environment endurance and user friendship.The test-bed was manufactured and put into practical use.The running results showed that the ORITS had fulfilled the design requirements.
Design and implementation of automatic comprehensive performance measurement system for emulsion pump

Feng Pingfa,Xu Daochun,Lu Guanyu,Zhou Xijie,Li Xuewei

DOI: https://doi.org/10.3321/j.issn:0254-3087.2007.12.021

2007-01-01

Abstract:The measurement of emulsion pump comprehensive performance is an important means to develop new product and guarantee product quality. Based on requirement analysis, an automatic measurement system of comprehensive performance for emulsion pump was designed and implemented. A variety of sensors are used to collect product running performance data automatically. Automatic loading is realized through using automatic control. Virtual instrument technique is adopted to realize data processing, analysis, management and measurement process automation. The developed experiment and measurement system has great driving effect for increasing product quality, updating product design level and decreasing new product development time.
Design of Bench Testing System for Electronic Controlled High-Pressure Common-Rail Diesel Engines

PENG Yi-gang,TANG Hang-bo,GONG Yuan-ming,DAI Xi-huai,YANG Lin,ZHUO Bin

DOI: https://doi.org/10.3969/j.issn.1000-0925.2005.03.014

2005-01-01

Abstract:A new design of bench testing system for electronic controlled high-pressure common-rail diesel engine was introduced and the testing theory and the structure of software were specially introduced. The input seize function of TPU in MC68376 was used to get some importance parameters of electronic control engine. This testing system applies to measure parameters in the development and calibration of the electronic controlled engine system. All functions of the system were tested on the GD-1 high pressure common rail diesel engine and the satisfied testing results were obtained.
The development of an integrated test jig for testing the SH3281 high-pressure pump and turning pump

ding guoqing,mao xuchu,yan detian

DOI: https://doi.org/10.3969/j.issn.1000-0682.2001.02.018

2001-01-01

Abstract:This paper describes the development of an integrated test jig for testing the SH3281 high pressure pump and turning pump.It is high automatic,high efficiency,high accuracy and high reliable.Different kinds of pump can be tested on this jig.The paper also recommends a kind of oil pump with minor pressure difference to substitute a burden machine.

Development of Performance Test System for Oil Pump in Automobile Engine

Design for ABS piston pump test system

The Development of the Static and Dynamic Performance Integrated Test System for Electro-hydraulic Servo Valve

Development And Simulation Of Lubrication Test System For Port Plate/Cylinder Block In Axial Piston Pump

Automatic Control System for a Torque Converter Static and Cycle Hydraulic Tester

Development of Experiment Rig for Lubricate Film of the Slipper-pad in Axial Piston Pumps

Comprehensive Performance Measurement for Closed-circuit Variable Displacement Pump

Development of Diesel Pump Performance Test System

Design and Simulation Study of a Vacuum-pumping Deaerating Device for Hydraulic Oil

Power Recovery Intelligent Testing System for Hydraulic Motor

A Study on the Noise and Vibration Testing System for Automotive Final Drive

Design and Implementation of Testing Device for Damping Oil Bulk Modulus and Fatigue Characteristic

An Automatic Testing System for Vehicle's Drive Axis Performance Test

Automatic Testing and Control System for Electro-Hydraulic Proportional Displacement Pump Based on LabVIEW

Intelligent Test Machine for Whole Performance Testing on Lube Pump

Hydraulic Pump Performance Test System Based on CAT Technology

R & D of an Automatic Testing System for Overall Performance of New Types of Motors

Oil Radiator's Integrative Test Control System Based on Microcontroller Unit

Design and implementation of automatic comprehensive performance measurement system for emulsion pump

Design of Bench Testing System for Electronic Controlled High-Pressure Common-Rail Diesel Engines

The development of an integrated test jig for testing the SH3281 high-pressure pump and turning pump