Abstract:The reduction in nitrogen oxides (NOx) emissions from heavy-duty diesel engines requires the development of more advanced combustion and control technologies to minimize the total cost of ownership (TCO), which includes both the diesel fuel consumption and the aqueous urea solution used in the selective catalytic reduction (SCR) aftertreatment system. This drives an increased need for highly efficient and clean internal combustion engines. One promising combustion strategy that can curb NOx emissions with a low fuel consumption penalty is to simultaneously reduce the in-cylinder gas temperature and pressure. This can be achieved with Miller cycle and by lowering the in-cylinder oxygen concentration via exhaust gas recirculation (EGR). The combination of Miller cycle and EGR can enable a low TCO by minimizing both the diesel fuel and urea consumptions. In this work, Miller cycle with late intake valve closing (IVC) and EGR technology were investigated on a single cylinder common rail heavy-duty diesel engine at high load operation of 24 bar net indicated mean effective pressure. The experiments were performed with a constant intake manifold pressure of 3 bar while optimizing the start of diesel injection to keep the peak in-cylinder pressure limit of 180 bar. The aqueous urea solution consumption in the SCR aftertreatment system was estimated to evaluate the effectiveness of the strategies in terms of TCO. The calculation was based on the engine-out NOx emissions and the Euro VI NOx limit. The results revealed that the use of the Miller cycle without EGR reduced NOx emissions by 35% and the net indicated efficiency by 4% when compared to the case with the baseline IVC at −178 crank angle degrees (CAD) after top dead center (ATDC). The introduction of 8%EGR decreased the levels of NOx by 54% while maintaining similar net indicated efficiency at the baseline IVC. The combination of Miller cycle with an IVC at −127 CAD ATDC and an EGR rate of 8% achieved the best trade-off between NOx and ISFC, decreasing the NOx levels by 57% and the fuel consumption by 1.6% compared to the baseline case. Soot emissions were maintained below the Euro VI limit of 0.01 g/kW h. Carbon monoxide emissions were maintained at low levels except for the combination of an IVC at −114 and an EGR rate of 8%. Unburned hydrocarbon emissions were slightly decreased with EGR and late IVCs likely due to relatively longer ignition delays and higher exhaust gas temperature. Overall, the analysis showed that the combination of Miller cycle with an IVC at −127 CAD ATDC and 8%EGR achieved the lowest total fluid consumption despite the reduction in net indicated thermal efficiency.

Numerical Investigation of Reducing In-Cylinder NOx Emissions on a Two-Stroke Marine Diesel Engine

Application of the Miller Cycle to Reduce NOx Emissions from Petrol Engines

Study on the Emission Characteristics in Renewable Energy Combustion under Different Working Conditions of Marine Two-Stroke Diesel Engine

Impact of Pilot Injection on Combustion and Emission Characteristics of a Low-Speed Two-Stroke Marine Diesel Engine

Miller Cycle with Early Intake Valve Closing in Marine Medium-Speed Diesel Engines

Investigation of the Miller cycle on the performance and emission in a natural gas-diesel dual-fuel marine engine by using two zone combustion model

Experimental investigation of the influences of Miller cycle combined with EGR on performance, energy and exergy characteristics of a four-stroke marine regulated two-stage turbocharged diesel engine

Three-Dimensional Computational Fluid Dynamics Modeling of the Combustion Process of a MAN L21/31 Marine Diesel Engine

Exploring the NOx Reduction Potential of Miller Cycle and EGR on a HD Diesel Engine Operating at Full Load

Optimization of Automatic Control System for $\text{no}_{\mathrm{x}}$ Emission Reduction in Smart Marine Diesel Engine

Numerical Investigations of Injection Timing Effects on a GDI Engine Performance: Part B, In-Cylinder Emission Formation and Oxidation Process

Numerical investigation on combustion regulation for a stoichiometric heavy-duty natural gas engine with hydrogen addition considering knock limitation

Study on Characteristics Optimization of Combustion and Fuel Injection of Marine Diesel Engine

Optimization of Marine Two-Stroke Diesel Engine Based on Air Intake Composition and Temperature Control

Numerical investigation on the combustion and emission characteristics of ammonia in a low-speed two-stroke marine engine

Effects of fuel reforming on large-bore low-speed two-stroke dual fuel marine engine combined with EGR and injection strategy

Effects of Exhaust Gas Recirculation on Combustion and Emission of a Marine Diesel Engine

Performance research and optimization of marine dual-fuel engine based on RSM and NSGA-II

Preliminary Numerical Study on Exhaust Emission Characteristics of Particulate Matters and Nitrogen Oxide in a Marine Engine for Marine Diesel Oil and Dimethyl Ether Fuel

Application of CFD, Taguchi Method, and ANOVA Technique to Optimize Combustion and Emissions in a Light Duty Diesel Engine

Numerical Research on Effects of Variable Port Timing on Performance of Marine Low-Speed Two-Stroke Engine