Abstract:This study proposes a clustered dynamic adaptive chemistry (CDAC) method, which uses an iterative K-means algorithm to partition the computational cells into different groups according to their similarity in terms of the temperature and significant species compositions. Taking advantage of the clustered cells, the averaged thermo-chemical properties of the cells in the respective clusters are then used to identify the adaptive dynamic reduced chemistry through the method of direct relation graph with error propagation (DRGEP). Moreover, the integration of the chemical source term, which commonly dominates the computational effort in reactive flow simulations, is now performed using the dynamic adaptive reduced chemistry at the cluster level instead of the cell level. With this CDAC method, the on-the-fly DRGEP process as well as the chemistry integration only needs to be conducted at the cluster level, dramatically reducing the unnecessary repeated computation for similar computational cells. In addition, the adaptive dynamic reduced chemistry further accelerates the chemistry integration process due to less ordinary differential equations (ODEs) to be solved for each cluster. This newly proposed CDAC method was tested in multi-dimensional homogeneous charged compression ignition engine (HCCI), direct injection compression ignition (DICI) engine and constant volume chamber combustion (CVCC) fueled with diesel, biodiesel and kerosene through the use of their respective surrogate fuel mechanisms under different operating conditions. The performance of CDAC in terms of accuracy and efficiency were extensively analyzed and discussed using different user-defined parameters, mechanisms with different surrogate components and number of species as well as different meshes with different number of grid cells. Based on this analysis, the error tolerances in DRGEP and the error tolerances of the temperature and significant species' mass fraction are recommended as: epsilon(d) <= 0.001, epsilon(T) 20K and epsilon(Y) <= 0.01 to achieve less than 0.1% integral error. With these recommended user-defined tolerances, it can be observed that the current CDAC method is able to accurately predict the in-cylinder pressure as well as the species profile in HCCI, DICI and the flame lift-off length in CVCC when compared with the full chemistry calculations as well as the experimental results. Moreover, with the recommended user defined error tolerances and a chemical kinetic model of 112 species, this CDAC method is capable of achieving a computational time speed-up factor of more than 3 compared to the conventional DAC and of almost 5 compared to the full chemistry. Finally, the CDAC method coupled CFD was applied to simulate a diesel DICI engine under three different engine speeds with a detailed primary reference fuel (PRF) mechanism of more than 1000 species. The 3-D simulation could be finished in acceptable CPU time while being able to well capture the experimental in-cylinder pressure and heat release rate for all the three engine speeds. (C) 2018 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Reaction Limit Analysis of Syngas Based on CO-DAC Method

Effect of Pressure and CO2 Dilution on Soot Formation in Laminar Inverse Coflow Flame at Conditions Close to Autothermal Reforming

Chemical Suppressive Effect of Ammonia Addition on Soot Formation in Laminar Diffusion Flames

A New Dynamic Adaptive Chemistry Reduction Method

A Direct Numerical Simulation Study on Combustion and NO Formation of Coal/ammonia Co-Firing Flames

Computational Acceleration of Multi-Dimensional Reactive Flow Modelling Using Diesel/biodiesel/jet-Fuel Surrogate Mechanisms Via a Clustered Dynamic Adaptive Chemistry Method

Dynamic Adaptive Chemistry for Turbulent Flame Simulations

Multi-timescale and Correlated Dynamic Adaptive Chemistry and Transport (CO-DACT) Modeling of Ignition and Flame Propagation of Jet Fuel Surrogate Mixtures

An optimized kinetic model for H 2 /CO combustion in CO 2 diluent at elevated pressures

The Use of Dynamic Adaptive Chemistry and Tabulation in Reactive Flow Simulations

Laminar Flame Speeds of Supercritical CO2 Diluted Oxy-Syngas and Oxy-Methane Flames under Direct-Fired Power Cycle Relevant Conditions

Effects of CO content on laminar burning velocity of typical syngas by heat flux method and kinetic modeling

Large Eddy Simulation of an N-Heptane Spray Flame with Dynamic Adaptive Chemistry under Different Oxygen Concentrations

Detailed Chemistry Modeling of Partial Combustion of Natural Gas for Coproducing Acetylene and Syngas

Assessment of dynamic adaptive chemistry with tabulated reactions for the simulation of unsteady multiregime combustion phenomena

Effects of CO 2 Dilution and CH 4 Addition on Laminar Burning Velocities of Syngas at Elevated Pressures: An Experimental and Modeling Study

Real-Time Conditional Commitment Logic

Dynamic adaptive chemistry via species time-scale and Jacobian-aided rate analysis

Experimental Study of the Effect of CO/H2 Ratio and Release Pressure on Syngas Jet Flame Propagation and Overpressure

Effects of CO2 Dilution and CH4 Addition on Laminar Burning Velocities of Syngas at Elevated Pressures: an Experimental and Modeling Study

Dynamic Adaptive Chemistry with Operator Splitting Schemes for Reactive Flow Simulations.