Abstract:Thermal management of lead-acid batteries includes heat dissipation at high-temperature conditions (similar to other batteries) and thermal insulation at low-temperature conditions due to significant performance deterioration. To address this trader-off, this work proposes a thermal management solution based on flexible phase change materials (PCMs) with moderate thermal conductivity and other favourable properties including high specific heat capacity and high latent heat. A novel type of flexible PCM sheets is prepared with paraffin, olefin block copolymers (OBC) and expanded graphite using the co-melting method. The flexible PCM sheets are attached to a common type of lead-acid battery packs (12 Ah, dimensions of 151 x 98 x 97 mm) and thermal management performance is experimentally investigated at -10 degrees C and 40 degrees C as low- and high-temperature conditions, respectively, along with 25 degrees C as a baseline case for comparison purposes. Thermal properties of the battery packs such as temperature regulation and electric properties including charge/discharge capacities and rates are studied synchronously based on a standard high-performance battery detection facility. The results indicate that at -10 degrees C condition, the PCM sheet enhances thermal insulation of the battery pack and significantly promotes the service temperature during the charging processes. Compared with a benchmark pack attached with an encapsulated sheet, the charge and discharge capacities of the PCM-attached pack are improved by 3.7% and 5.9%, respectively. At 40 degrees C condition, phase transition of the PCM sheet restrains the temperature rise of the battery pack, with a maximum temperature decrease of 4.2 degrees C during the charging processes relative to the benchmark pack, and the temperature of the PCM-attached pack is maintained below 45 degrees C across 60% of the overall charge period. The overcharge and overdischarge have also been alleviated by 3.2% and 2.8%, respectively, and thus the running stability and service lifespan can be improved. The proposed PCM sheets with preferable thermal properties demonstrate potential to promote performance of lead-acid battery packs and such components are also expected to improve heat dissipation and thermal insulation in similar applications including building energy saving, thermal management of electronic chips and thermal regulation of electronic devices.

Battery pack thermal management based on thermo electric cooling and phase change material heat preservation

Thermal Management of Standby Battery for Outdoor Base Station Based on the Semiconductor Thermoelectric Device and Phase Change Materials

Thermal Performance of Pouch Lithium-ion Battery Module Cooled by Phase Change Materials

Synergistic Performance Enhancement of Lead-Acid Battery Packs at Low- and High-Temperature Conditions Using Flexible Phase Change Material Sheets

Optimization of heat transfer and temperature control of battery thermal management system based on composite phase change materials

Performance of a Combined Battery Thermal Management System with Dual-Layer Phase Change Materials and Air Cooling Technologies

Thermal Management of 48 V Standby Battery for Outdoor Base Station at Cold Environment

Investigation of multifactorial effects on the thermal performance of battery pack inserted with multi-layer phase change materials

Analysis of a Battery Pack with a Phase Change Material for the Extreme Temperature Conditions of an Electrical Vehicle

Thermal management of Lithium-ion battery pack through the application of flexible form-stable composite phase change materials

Thermal management analysis of new liquid cooling of a battery system based on phase change material and thermoelectric cooler

Parameter optimization and sensitivity analysis of a Lithium-ion battery thermal management system integrated with composite phase change material

Modeling analysis on the cooling efficiency of composite phase change material-heat pipe coupling system in battery pack

Experimental Study of Battery Passive Thermal Management System Using Copper Foam-Based Phase Change Materials

Design of battery thermal management system based on phase change material and heat pipe

Experimental Study on Thermal Management of Batteries Based on the Coupling of Metal Foam-Paraffin Composite Phase Change Materials and Air Cooling

Experiment and simulation of a LiFePO4 battery pack with a passive thermal management system using composite phase change material and graphite sheets

Experimental and Numerical Investigations of a Thermal Management System Using Phase-Change Materials and Forced-Air Cooling for High-Power Li-Ion Battery Packs

Study of a novel thermal management system using double-layer liquid-cooled plate-coupled PCM under high-rate discharge

Battery thermal management systems (BTMs) based on phase change material (PCM): A comprehensive review

Experimental Study on the Application of Phase Change Material in the Dynamic Cycling of Battery Pack System