Abstract:Two series of uniaxial tensile tests are performed on isotactic polypropylene with the strain rates ranging from 5 to 200mm/min. In the first series, injection-molded specimens are used without thermal pre-treatment. In the other series of experiments, the samples are annealed for 51h at 160°C prior to testing.A constitutive model is developed for the viscoplastic behavior of isotactic polypropylene at finite strains. A semicrystalline polymer is treated as equivalent heterogeneous network of chains bridged by permanent junctions (physical cross-links and entanglements). The network is thought of as an ensemble of meso-regions connected with each other by links (lamellar blocks). In the sub-yield region of deformations, junctions between chains in meso-domains slide with respect to their reference positions (which reflects sliding of nodes in the amorphous phase and fine slip of lamellar blocks). Above the yield point, the sliding process is accompanied by displacements of meso-domains in the ensemble with respect to each other (which reflects coarse slip and fragmentation of lamellar blocks). To account for alignment of disintegrated lamellar blocks along the direction of maximal stresses (which is observed as strain-hardening of specimens in the post-yield regions of deformations) elastic moduli are assumed to depend on the principal invariants of the right Cauchy–Green tensor for the viscoplastic flow.Stress–strain relations for a semicrystalline polymer are derived by using the laws of thermodynamics. The constitutive equations are determined by five adjustable parameters that are found by matching observations. Fair agreement is demonstrated between the experimental data and the results of numerical simulation. A noticeable difference is revealed between the mechanical responses of non-annealed and annealed specimens: (i) necking of samples not subjected to thermal treatment precedes coarse slip and fragmentation of lamellar blocks, whereas cold-drawing of annealed specimens up to a longitudinal strain of 80% does not induce spatial heterogeneity of their deformation; (ii) the elastic modulus increases with the strain rate for non-annealed specimens and decreases for annealed samples.

Experimental Study of Relationship Between Flow-Induced Stress and Strain During Polymer Shear Flow Process

STRESS-INDUCED POLYMER DEFORMATION IN SHEAR FLOWS

Application of an Interpenetrating Network Model to the Necking in the Microcrystalline Region in Four Annealed Isotactic Polypropylene Films Subjected to Uniaxial Stretching at Room Temperature

Molecular Orientations and True Stress−Strain Relationship in Isotactic Polypropylene Film

Effect of shear flow on the transverse thermal conductivity of polymer melts

Determination of dynamic flow stress equation based on discrete experimental data: Part 1 Methodology and the dependence of dynamic flow stress on strain-rate

Deformation Mechanisms of Polymer Thin Films by Simultaneous Kinetic Measurement of Microscopic Infrared Dichroism and Macroscopic Stress. Part Iii: Influence of Morphology on Molecular Orientation of Isotactic Polypropylene Films Subjected to Uniaxial Stretching

Experimental Methodology for Obtaining the Flow Curve of Sheet Materials in a Wide Range of Strains

Injection molding and shear‐induced stress simulation of poly (styrene‐ethylene‐butylene‐styrene) and polypropylene blends

Experimental Study of Yield Surface in Polypropylene Considering Rate Effect: Stress Path Dependence

The effect of strain rate on the viscoplastic behavior of isotactic polypropylene at finite strains

Stress Relaxation Characteristics and Extrudate Swell of the IUPAC-LDPE Melt

Simulation and Analysis of the Loading, Relaxation, and Recovery Behavior of Polyethylene and Its Pipes

Research on Flow Pattern and Molecular Mechanisms of Polymer Molten During Injection Filling Stage

A Rheological Study on Wall Slip of Polymer Melts

The effect of rotationality on nonlinear shear flow of polymer melts and solutions

Overshoots in Stress and Free Energy Change During the Flow-Induced Crystallization of Polymeric Melt in Shear Flow

Stress-Strain curves for solid polymers

Universal Scaling Behaviors of Entangled Polymer Melts at High-stress Shear

Influence of Shear Flow on the Crystallization Kinetics of Isotactic Polypropylene in Nucleation and Crystal Growth Processes