Abstract:Statement of problem: Three-dimensional printing has the potential for clinical applications, and additive manufacturing materials for dental use merit further investigation. Purpose: The purpose of this in vitro study was to evaluate the properties of materials formulated with ethoxylated bisphenol A-dimethacrylate (Bis-EMA), urethane dimethacrylate (UDMA), and triethylene glycol dimethacrylate (TEGDMA) as 3D printing resins for ultraviolet digital light processing (UV-DLP) 3D printers and to characterize the mechanical and biological properties and accuracy of the printed objects. Material and methods: Ten different light-polymerized resins were formulated using Bis-EMA, UDMA, and TEGDMA. Their viscosities were measured, and only 7 resins with viscosities lower than 1500 centipoise (cP) were selected for 3D printing and further material characterization. The light-polymerized resins were printed into representative shapes using a custom-made 3D printer equipped with a 405-nm UV-DLP projector as the light source. The printed specimens were subjected to biologic, mechanical, and accuracy tests, and the data were submitted to 1-way ANOVA and Tukey post hoc comparisons (α=.05). Results: Photopolymerizable resins made of Bis-EMA, UDMA, and TEGDMA were successfully formulated for 3D printing to fabricate objects of various shapes and sizes. TEGDMA served as the diluent to reduce the viscosity and increase the degree of conversion, while UDMA and Bis-EMA provided strength as demonstrated by the mechanical testing. All the printed objects passed cytotoxicity testing. The flexural strengths of the printed specimens ranged between 60 MPa and 90 MPa; flexural modulus ranged between 1.7 GPa and 2.1 GPa; and surface hardness ranged between 14.5 HV and 24.6 HV. These represent similar mechanical properties to those of currently used clinical resin materials. In the accuracy test, the resin mixture composed of 80% Bis-EMA, 10% UDMA, and 10% TEGDMA had the highest accuracy, with a 0.051-mm deviation from the original design. Conclusions: Bis-EMA, UDMA, and TEGDMA are good candidates for the formulation of 3D printing resins for dental use. The printed objects demonstrated favorable biological and mechanical properties. Further, the accuracy of the printed specimens showed potential for clinical application.

Preparation of hydroxyl acrylic copolymerized resin as prototyping powder with flexibility for three dimensional printing

Preparation of carboxyl acrylic resin microemulsion and its application in 3D printing

Acrylate-based photosensitive resin for stereolithographic three-dimensional printing

Development of Bisphenol-A-Glycidyl-Methacrylate- and Trimethylolpropane-Triacrylate-Based Stereolithography 3D Printing Materials

Synthesis and characterization of a dual-curing resin for three-dimensional printing

Synthesis and properties of a low-viscosity UV-curable oligomer for three-dimensional printing

Design of enhanced mechanical properties by interpenetrating network of 3D printing dual-curing resins

Projection Printing of Scaffolds with Shape Recovery Capacity and Simultaneously Improved Stiffness and Toughness Using an Ultra-fast-curing Poly(propylene Fumarate)/hyperbranched Additive Resin

Synthesis of Photosensitive Oligomer and Its Use for Three Dimensional Printing

The Properties of an UV Curable Support Material Pre-Polymer for Three Dimensional Printing

Preparation of polycarbonate/poly(lactic acid) with improved printability and processability for fused deposition modeling

Study on the preparation of long-term stability core–shell particles/epoxy acrylate emulsion and toughening improvement for 3D printable UV-curable resin

"Dissolve‐on‐Demand" 3D Printed Materials: Polymerizable Eutectics for Generating High Modulus, Thermoresponsive and Photoswitchable Eutectogels

Silicone–Epoxy‐Based Hybrid Photopolymers for 3D Printing

Preparation and characterization of photocurable fluorinated polyether‐based reactive inks

Mechanical properties, accuracy, and cytotoxicity of UV-polymerized 3D printing resins composed of Bis-EMA, UDMA, and TEGDMA

3D printing of release-agent retaining molds

Synthesis and Characterization of Cardanol-Based Methacrylate Oligomers for Three-Dimensional Printing Resins

Preparation of Poly(vinyl Alcohol)/poly(lactic Acid)/hydroxyapatite Bioactive Nanocomposites for Fused Deposition Modeling

Aliphatic silicone‐epoxy based hybrid photopolymers applied in stereolithography 3D printing

Process Analysis of DLP Photocuring 3D Printing with Modified High-strength Resin