Study on Static and Dynamic Behavior of T-Frame Bridge Reinforced by External Tendons

Fengqiang HU,Yongding YAO,Yiqiang Xiang,Airong CHEN

DOI: https://doi.org/10.3969/j.issn.1005-0159.2005.02.015

2005-01-01

Abstract:Based on a typical T-frame bridge reinforced by external prestressing tendons, the behavior of static and dynamic is completed by 3D finite element. The field test is made, and some helpful conclusions are drawn as well.

What problem does this paper attempt to address?

Case Study on Stability Performance of Asymmetric Steel Arch Bridge with Inclined Arch Ribs

Xinke Hu,Xu Xie,Zhanzhan Tang,Yonggang Shen,Pu Wu,Lianfeng Song

DOI: https://doi.org/10.12989/scs.2015.18.1.273

2015-01-01

Steel and Composite Structures

Abstract:As one of the most common failure types of arch bridges, stability is one of the critical aspects for the design of arch bridges. Using 3D finite element model in ABAQUS, this paper has studied the stability performance of an arch bridge with inclined arch ribs and hangers, and the analysis also took the effects of geometrical and material nonlinearity into account. The impact of local buckling and residual stress of steel plates on global stability and the applicability of fiber model in stability analysis for steel arch bridges were also investigated. The results demonstrate an excellent stability of the arch bridge because of the transverse constraint provided by transversely-inclined hangers. The distortion of cross section, local buckling and residual stress of ribs has an insignificant effect on the stability of the structure, and the accurate ultimate strength may be obtained from a fiber model analysis. This study also shows that the yielding of the arch ribs has a significant impact on the ultimate capacity of the structure, and the bearing capacity may also be approximately estimated by the initial yield strength of the arch rib.
EXPERIMENTAL STUDY ON FLEXURAL BEHAVIOR OF REINFORCED CONCRETE BEAMS PRE-STRESSED WITH CFRP TENDONS

Jian-lin HU,Long-wei WANG,Long-cheng CAO,Xiao-yan SUN

DOI: https://doi.org/10.3969/j.issn.1001-6864.2013.05.014

2013-01-01

Abstract:In order to investigate the flexural behavior of reinforced concrete bridge girder prestressed with external carbon fiber reinforced polymer(CFRP) tendons,the experimental data of different type of bridge girders prestressed with external tendons were analysized.The investigation results indicate that the flexural behavior of concrete girders with externally prestressed CFRP tendons are similar to that with external steel tendons in many aspects.The external prestressed CFRP tendons can improve bearing capacity and reduce their deformation and crack remarkably.The initial loading state on the girders before tendon jacking has no significant effect on the capacity and deflection.The stress improvement of CFRP appeared after the yield of non-prestressing reinforcing steel rebar.
Quasi-static Testing and Networked Pseudo-Dynamic Testing on Fiber Reinforced Plastic Retrofitted Reinforcement Concrete Short Columns of Bridge

Xinjiang CAI,Shizhu TIAN,Dapeng WANG,Wei WANG,Yan XIAO,Xuhua DONG

DOI: https://doi.org/10.3321/j.issn:1000-6869.2009.02.016

2009-01-01

Abstract:Since reinforcement concrete short column of bridge had a large stiffness but its shear span ratio was small,the seismic testing method was used to explore the seismic performances.Seven specimens lacking of shearing strength were constructed,quasi-static testing(QST) and the networked pseudo-dynamic testing(NPDT) were carried out under an invariable axial force,the models included specimens which were not retrofitted,specimens retrofitted by carbon fiber reinforced plastic(CFRP) and specimens retrofitted by glass fiber reinforced plastic(GFRP).The results under different working conditions were analyzed and compared.The hysteretic curve,skeleton curve,energy dissipation curve and stiffness degradation curve were obtained.Furthermore,the ductility,strength and stiffness were researched,and the difference between results of QST and NPDT were compared.The results indicate that the RC short columns retrofitted by fiber reinforced plastic have superior ductility so as to enhance the seismic performances effectively,but have no influence on dynamic characteristics.The energy dissipation capacity of specimens under NPDT is less than under QST.The research provides reference to seismic analysis and engineering design of retrofitted reinforcement concrete structures.
Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Zhang Zhi-cheng,Xie Xu,Zhang He,Chen Heng-zhi

DOI: https://doi.org/10.1631/jzus.2007.a0682

2007-01-01

Abstract:A convenient approach is proposed for analyzing the ultimate load carrying capacity of concrete filled steel tubular (CFST) arch bridge with stiffening girders. A fiber model beam element is specially used to simulate the stiffening girder and CFST arch rib. The geometric nonlinearity, material nonlinearity, influence of the construction process and the contribution of prestressing reinforcement are all taken into consideration. The accuracy of this method is validated by comparing its results with experimental results. Finally, the ultimate strength of an abnormal CFST arch bridge with stiffening girders is investigated and the effect of construction method is discussed. It is concluded that the construction process has little effect on the ultimate strength of the bridge.
Finite-element Analysis for Nonlinear Stabilities of Concrete-filled Steel Tubular Arch Bridges

JIAO Yu-Feng,YI Jian-Long,CHEN Shui-Fu

2008-01-01

Abstract:Owing to the limitation of establishing finite element model of concrete-filled steel tubular(CFST) arch bridge,the more precision model has been put forward.Namely the outer steel tubes,the inner concrete and the reinforcing steel bars have their own elements.Using this method,a CFST arch bridge's deflection curve under different load is obtained considering the material and geometric nonlinearity.The computed results are in agreement with the test data.The result shows that the method used in this paper has better adaptability and definition.
Remote Collaborative Pseudo-dynamic Testing of Carbon Fiber Reinforced Plastic Retrofitted Reinforcement Concrete Short Columns of Bridge

Xinjiang Cai,TIAN Shi-zhu,WANG Da-peng,XIAO Yan,FAN Yun-lei

2008-01-01

Abstract:Since the existing circle crossing reinforcement concrete short columns of bridge can't satisfy new seismic codes,retrofitted by Fiber Reinforced Plastic and loaded with an invariable axial force,the first domestic remote collaborative pseudo-dynamic testing of a whole bridge was carried out with a platform named NetSLab.The damage phenomena,ductility and energy dissipation of two shearing columns retrofitted by Carbon Fiber Reinforced Plastic were analyzed.The results indicated that Carbon Fiber Reinforced Plastic not only prevented brittle shearing damage of reinforcement concrete short columns,but also changed the damage mode to ductile bending damage.The stable hysteretic properties,energy dissipation capacities and seismic performances of reinforcement concrete short columns were effectively improved.
STUDY ON THE RIGID FRAME BRIDGE STRENGTHENED BY EXTERNAL PRESTRESSING TENDONS AND ANCHOR BLOCKS

Yang Lingming,Jiang Haibo,Zou Jinhua,He Aide

DOI: https://doi.org/10.13204/j.gyjz2010.10.003

2010-01-01

Abstract:With the increase of traffic volumn and the improvement of load grade,the issue of old bridge reinforcement becomes more prominent.In order to study the structural performance of large-span rigid frame bridges strengthened by external prestressing tendons and the spatial stress distribution of anchor blocks,the finite element program ANSYS is used to analyzed respectively the load bearing capacity of the strengthened continuous rigid frame bridge with the main span of 160 m and the spatial stresses of side-span anchor block.The results show that external prestressing can enhance the carrying capacity effectively and improve structural performance significantly,and large-span continuous rigid frame bridge strengthened by external prestressing tendons is effective and practicable;meanwhile,it is pointed out that the principal tensile stresses of the box girder at anchorage zone are existing in the box girder edge and the crossover port edge are also described.The results can provide a reference for the reinforcement of similar bridges.
Study on Typical Dynamic Characteristics of a Long-span Prestressed Concrete Cable-stayed Bridge

JING Long-jiang,XIANG Yi-Qiang,WANG Jing-feng

DOI: https://doi.org/10.3969/j.issn.1004-4655.2007.01.007

2007-01-01

Abstract:The paper presented several types of finite-element model based on a typical long-span prestressed concrete cable-stayed bridge,established its precise and validated three-dimensional finite element model, and analyzed its dynamic properties. The conclusion indicates that the typical cable-stayed bridge has a lower natural frequency and dense modal, exists many coupled vibration.
Finite Element Modeling of Concrete Beams Prestressed with External Tendons

Tie-jiong Lou,Yi-qiang Xiang

DOI: https://doi.org/10.1016/j.engstruct.2006.03.020

2006-01-01

Abstract:In this study, a numerical model based on the finite element method incorporating an arc-length solution algorithm for materially and geometrically nonlinear analysis of concrete beams prestressed with external tendons is established. The second-order effects are taken into account. The effects of external tendons are expressed by equivalent nodal loads of the beam element and therefore analysis of externally prestressed concrete beams can be conducted with the ordinary bonded concrete beams. The section tangent stiffness matrix is derived by the layered approach, and then the nonlinear beam flexural theory is utilized to determine the element tangent stiffness matrix. An updated normal plane arc-length solution algorithm is used to trace the nonlinear response of the beams from zero loads up to ultimate loads. This algorithm can deal well with the changes of response during loading, so that the possible limit points on the load–deflection response prior to the ultimate limit state can be easily passed. Results predicted by the analysis are in good agreement with the experimental data.
Study on Method of Simulating Spatial Effect of Prestressing Force in Bridge

WANG Jin-feng,XIANG Yi-qiang,XU Xing

DOI: https://doi.org/10.3969/j.issn.1007-4708.2007.04.014

2007-01-01

Abstract:With extensive use of prestressing force,the stress state of bridge structure becomes more complex,and it is necessary to analyze the bridge structure with three-dimensioned method.But for prestressed reinforcement's number and its shape, it is difficult to simulate the spatial effect of prestressing force.Based on prestressing force's mechanism,it was proposed that equivalent node load was used to simulate its spatial effect during tensing,and that degenerated solid element was employed to take prestressed reinforcement as a part of structure and to analyze structure after grouting.The method discussed in the paper was confirmed by two examples.The result of analysis shows that this method can really simulate the spatial effect of prestressing force,and can be used to three-dimensioned analysis of prestressed concrete bridge.
Reinforcement Analysis of an Old Multi-Beam Box Girder Based on a New Embedded Steel Plate (ESP) Strengthening Method

Yuliang He,Kai Wang,Zongyong Cao,Peijuan Zheng,Yiqiang Xiang

DOI: https://doi.org/10.3390/ma15124353

IF: 3.4

2022-01-01

Materials

Abstract:Multi-beam box girder bridges have been applied widely throughout the world for many years. However, the cracking of longitudinal joints between the box girders always leads to reflective cracking of the bridge decks during the service period and thus finally affects the safety and durability of the actual bridges. An embedded steel plate (ESP) strengthening method was presented by introducing carbon-A/-B glue to reinforce the longitudinal joints of old multi-beam box girder bridges for this problem. In order to evaluate the feasibility of the proposed method for actual bridges, an old multi-beam box girder bridge was reinforced, and structural parameters including strain, frequency, and deflection were obtained by adopting field tests before and after strengthening. In addition, the corresponding finite element (FE) model of the background bridge was also set up using ANASYS 18.0 to analyze the strengthening process. Analysis results of the actual bridge and FE model indicate that structural stiffness and load lateral transferring performance between the box girders were enhanced after ESP strengthening. Therefore, this proposed strengthening method can be used to improve the mechanical performance of multi-beam box girder bridges and provide reference for such bridge reinforcement.
Spatial behavior and strengthening analysis of fabricated PC hollow slab beam bridge with hinge joints

Yiqiang Xiang,Cheng Xing,Linhai Shao,Yuan Xing,Chunfeng Chao

DOI: https://doi.org/10.3969/j.issn.1001-0505.2012.04.030

2012-01-01

Abstract:To ascertain the crack mechanism along the hinge joints of fabricated PC (prestressed concrete) hollow slab beam bridges and the strengthening method, a typical fabricated hollow slab beam bridge was taken as an example and an accurate three-dimensional finite element model was built by simulating the whole bridge using entity unit. The stresses in the control sections of the bridge were analysed to conclude that the main cause of longitudinal cracks along the hinge joints was the excess of transverse stress. Based on above analysis results, two schemes including adding transverse prestress steel wire system to strengthen and improve the transverse load bearing capacity of such kind of bridges were presented, and numerical analyses and comparison of the two strengthening schemes were conducted. The results show that both strengthening schemes can effectively reduce the transverse tensile stresses in the hinge joints of hollow slab beam bridges and greatly improve the integrity of the bridge. The scheme with the prestressed steel wire set in the area 25 cm from the bottom of the beam is more effective and has more advantages in durability and security.
Field Test and Analysis for the Static and Dynamic Behaviour of Multi-Box Steel Concrete Composite Girder Bridge

Yu Liang He,Yi Qiang Xiang,He-xin Ke,Li Si Liu

DOI: https://doi.org/10.4028/www.scientific.net/amm.226-228.1547

2012-01-01

Applied Mechanics and Materials

Abstract:Taking the four-span 40m simply supported multi-box steel-concrete composite girder bridge in the ProjectⅡ of Qiushi Expressway in Hangzhou as the background, this paper analyzed the static and dynamic behaviour of the bridge by FEM, then finished a field test study for the bridge. Finally, comparing the test values with the results obtained from FEM analysis, it was verified that the rigidity transverse beam method with infinte stiffness is also adaptive to caculating and predicting the load transverse distribution of the multi-box steel-concrete composite bridge. Steel diaphragm and stiffening rib of the multi-box steel- concrete composite bridge can improve the flexural capacity of bridge to some extent, so these contributions should be reasonably considered during the design stage in order to reduce the engineering cost. The measured modes agree well with the results from FEM.
Stiffness Degradation Characteristics Destructive Testing and Finite-Element Analysis of Prestressed Concrete T-Beam

Chengquan Wang,Yonggang Shen,Yun Zou,Tianqi Li,Xiaoping Feng

DOI: https://doi.org/10.3970/cmes.2018.114.075

2018-01-01

Abstract:The failure behavior of the precast prestressed concrete T girder was investigated by destructive test and finite-element analysis, and the mid-span deflection, girder stiffness and the variation of the cross section strain in the loading process were obtained, and the mechanical properties, mechanical behavior, elastic and plastic behavior and ultimate bearing capacity of T girder with large span were revealed. Furthermore, the relationship between the beam stiffness degradation, the neutral axis in cross-section, steel yielding and concrete cracking are investigated and analyzed. A method was proposed to predict the residual bearing capacity of a bridge based on the variation of the position of the cross section strain distribution and the section neutral axis, which provided a theoretical basis for predicting the stiffness detection and carrying capacity assessment of prestressed concrete beam.
Static load test of RC T-beam bridge flexural strengthening with externally bonded steel plates

Xilong Zheng,Hao Du,Runbo Zhang,Qinglin Ma,Hongshuai Gao

DOI: https://doi.org/10.1088/1755-1315/791/1/012018

2021-06-01

IOP Conference Series: Earth and Environmental Science

Abstract:Abstract Externally bonding steel plates is a common method for strengthening old bridges. Structural features and diseases of T-beam bridge are described. The strengthening project of Erdao River Bridge was taken as an example. Based on static load test, changes of deflection and stress are studied at the bottom of RC T-beams strengthened by externally bonding steel plates in the loading process. Numerical simulation is also carried out. The results of static test show that bearing capacity, bending stiffness and deformation can be improved of T-beams strengthened with bonding steel plates. This paper provides good engineering practice experience for the reasonable application of bridge with externally bonding steel plate strengthening method.
Simulating analysis of cantilever casting of prestressed concrete bridge

Jinfeng Wang,GuangYu Wu,Yiqiang Xiang,Xing Xu

2006-01-01

Abstract:It is difficult to simulate cantilever casting of prestressed concrete bridge with traditional beam theory. Based on a new three-dimensional element named degenerated solid element, the methods of calculating effects of tendon tensioning and concrete creeping were discussed. The prestressing tendons were taken as a part of structure, and equivalent node loads were used to simulate tendons' spatial effect during tensing. The three parameter viscoelastic model was put forward to analyze the effect of concrete creeping. By the methods, the cantilever casting of a long-span prestressed concrete bridge was really simulated. The result of analysis shows that themethod is efficient and can be used to simulate cantilever casting of complex prestressed concrete bridge. The construction safety and anti-crack performance can be assured by the above methods.
Structural Analyses of Extruded CFRP Tendon-Anchor System and Applications in Thin-Walled Aluminum/cfrp Bridge

Pengcheng Zhu,Pengcheng Ai,Yinzhi Zhou,Longxing Xu,Hualin Fan

DOI: https://doi.org/10.1016/j.tws.2018.02.029

IF: 5.881

2018-01-01

Thin-Walled Structures

Abstract:Pre-stressed carbon fiber reinforced polymer (CFRP) tendon system is developed. Extrusion method guarantees the strength of the CFRP tendon could be fully used in strengthening. The pre-stressed CFRP tendons are applied to strengthen aluminum beams and portable aluminum bridge to improve the flexural rigidity and load carrying capacity of these structures and the improvements are revealed by the experiments. Applying extruded CFRP tendon-anchor system, the load carrying ability of the pre-stressed aluminum bridge has an improvement of 25%. Structural models are proposed to investigate the pre-stressing effects, including the deflection and the load capacity under different design criteria. Finite element method (FEM) is applied to analyze the nonlinear behavior of the pre-stressed beam and reveal the plastic torsional buckling failure style. All these analyses agree well with the experiments and suggest accurate methods to design pre-stressed aluminum/CFRP structures.
Experimental study on failure mechanism of prestressed concrete T girder

WANG Chengquan,SHEN Yonggang,YANG Runfang,ZOU Yun

DOI: https://doi.org/10.3969/j.issn.1672-7029.2017.11.014

2017-01-01

Abstract:This paper presents the results of an experimental and analytical study on the failure behavior of a new precast prestressed concrete T girder. The mid-span deflection, girder stiffness and the variation of the cross section strain in the loading process were obtained. The applicability of plane section assumption in the whole stress process of prestressed concrete T girder was verified. A method was proposed to predict the residual bearing capacity of a bridge based on the variation of the position of the cross section strain distribution and the section neutral axis. The mechanical properties, mechanical behavior, elastic and plastic behavior and ultimate bearing capacity of T girder with large span were revealed. The relationships between the load and the deflection, the stress and the neutral axis of the T girder were investigated in this paper, which provides a theoretical basis for predicting the ultimate bearing capacity of the T girder bridge.
SIMULATION FOR CONSTRUCTION PROCESS OF P.C. CONTINUOUS RIGID FRAME BRIDGE

XUE Peng-fei,WANG Jin-feng,XIANG Yi-qiang

2010-01-01

Abstract:For a modem P.C. (prestressed concrete) continuous rigid frame bridge, its stress state is complicated, and affected by construction process. To simulate its structural behavior during construction process, degenerate solid elements were used and a three-dimensional model was set up. Taking prestressed reinforcement as a part of structure, the equivalent nodal load was obtained to calculate the effect of tensioning bars. A three-parameter viscoelasticity model was adopted to simulate the concrete creep. A processing method for internal stress of stage model was developed. A P.C. continuous rigid frame bridge was employed for the case study. The results show that the stresses and deflections of P.C. continuous rigid frame bridge under dead loads are closely related to construction process, and that the stresses and deflections obtained with commonly-used method which ignores the effect of construction process have large deviation.
Study of Dynamic Behavior and Influences Induced by Structural Parameter Variations of Self-Anchored Suspension Bridge

丰硕,项贻强,谢旭,黄志义

DOI: https://doi.org/10.3969/j.issn.1671-7767.2004.04.015

2004-01-01

Abstract:By way of example of Beiguan Bridge, a concrete self-anchored suspension bridge to be built in Jiangshan, Zhejiang,the spatial finite element model for the type of the bridge is established, using the general program ANSYS, and the first 20 orders of vibration frequency and vibration modes of the bridge are calculated. The influences induced by variations of structural parameters, such as those of dead load, stiffening girder rigidity and tower rigidity, on the dynamic behavior of the bridge are then analyzed in a specific way. Meanwhile, a simulated suspension bridge having the same structural size, but anchored on the ground is analyzed for comparison purpose. The dynamic behavior of the two kinds of suspension bridges is compared, and some helpful conclusions are generalized, which provides reference to the analysis of the natural vibration, wind resistance design and aseismatic design of the concrete self-anchored suspension bridge.

Study on Static and Dynamic Behavior of T-Frame Bridge Reinforced by External Tendons

Case Study on Stability Performance of Asymmetric Steel Arch Bridge with Inclined Arch Ribs

EXPERIMENTAL STUDY ON FLEXURAL BEHAVIOR OF REINFORCED CONCRETE BEAMS PRE-STRESSED WITH CFRP TENDONS

Quasi-static Testing and Networked Pseudo-Dynamic Testing on Fiber Reinforced Plastic Retrofitted Reinforcement Concrete Short Columns of Bridge

Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Finite-element Analysis for Nonlinear Stabilities of Concrete-filled Steel Tubular Arch Bridges

Remote Collaborative Pseudo-dynamic Testing of Carbon Fiber Reinforced Plastic Retrofitted Reinforcement Concrete Short Columns of Bridge

STUDY ON THE RIGID FRAME BRIDGE STRENGTHENED BY EXTERNAL PRESTRESSING TENDONS AND ANCHOR BLOCKS

Study on Typical Dynamic Characteristics of a Long-span Prestressed Concrete Cable-stayed Bridge

Finite Element Modeling of Concrete Beams Prestressed with External Tendons

Study on Method of Simulating Spatial Effect of Prestressing Force in Bridge

Reinforcement Analysis of an Old Multi-Beam Box Girder Based on a New Embedded Steel Plate (ESP) Strengthening Method

Spatial behavior and strengthening analysis of fabricated PC hollow slab beam bridge with hinge joints

Field Test and Analysis for the Static and Dynamic Behaviour of Multi-Box Steel Concrete Composite Girder Bridge

Stiffness Degradation Characteristics Destructive Testing and Finite-Element Analysis of Prestressed Concrete T-Beam

Static load test of RC T-beam bridge flexural strengthening with externally bonded steel plates

Simulating analysis of cantilever casting of prestressed concrete bridge

Structural Analyses of Extruded CFRP Tendon-Anchor System and Applications in Thin-Walled Aluminum/cfrp Bridge

Experimental study on failure mechanism of prestressed concrete T girder

SIMULATION FOR CONSTRUCTION PROCESS OF P.C. CONTINUOUS RIGID FRAME BRIDGE

Study of Dynamic Behavior and Influences Induced by Structural Parameter Variations of Self-Anchored Suspension Bridge