Bi(Mg0.5Hf0.5)O3-modified SrTiO3 Lead-Free Ceramics for High-Temperature Energy Storage Capacitors

Kong Xi,Yang Letao,Cheng Zhenxiang,Zhang Shujun

DOI: https://doi.org/10.1557/s43578-020-00007-2

2021-01-01

Abstract:A correction to this paper has been published: https://doi.org/10.1557/s43578-021-00216-3

What problem does this paper attempt to address?

Ultrahigh Energy Storage Properties in (Sr 0.7 Bi 0.2 )TiO 3 -Bi(Mg 0.5 Zr 0.5 )O 3 Lead-Free Ceramics and Potential for High-Temperature Capacitors.

Xi Kong,Letao Yang,Zhenxiang Cheng,Shujun Zhang

DOI: https://doi.org/10.3390/ma13010180

2020-01-01

Abstract:Due to the enhanced demand for numerous electrical energy storage applications, including applications at elevated temperatures, dielectric capacitors with optimized energy storage properties have attracted extensive attention. In this study, a series of lead-free strontium bismuth titanate based relaxor ferroelectric ceramics have been successfully synthesized by high temperature solid-state reaction. The ultrahigh recoverable energy storage density of 4.2 J/cm under 380 kV/cm, with the high efficiency of 88%, was obtained in the sample with = 0.06. Of particular importance is that this ceramic composition exhibits excellent energy storage performance over a wide work temperature up to 150 °C, with strong fatigue endurance and fast discharge speed. All these merits demonstrate the studied ceramic system is a potential candidate for high-temperature capacitors as energy storage devices.
Ultrahigh Energy Storage Properties in (Sr0.7Bi0.2)TiO3-Bi(Mg0.5Zr0.5)O3 Lead-Free Ceramics and Potential for High-Temperature Capacitors

Xi Kong,Letao Yang,Zhenxiang Cheng,Shujun Zhang

DOI: https://doi.org/10.3390/ma13010180

IF: 3.4

2020-01-01

Materials

Abstract:Due to the enhanced demand for numerous electrical energy storage applications, including applications at elevated temperatures, dielectric capacitors with optimized energy storage properties have attracted extensive attention. In this study, a series of lead-free strontium bismuth titanate based relaxor ferroelectric ceramics have been successfully synthesized by high temperature solid-state reaction. The ultrahigh recoverable energy storage density of 4.2 J/cm3 under 380 kV/cm, with the high efficiency of 88%, was obtained in the sample with x = 0.06. Of particular importance is that this ceramic composition exhibits excellent energy storage performance over a wide work temperature up to 150 °C, with strong fatigue endurance and fast discharge speed. All these merits demonstrate the studied ceramic system is a potential candidate for high-temperature capacitors as energy storage devices.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Ultrahigh Energy Storage Properties in (Sr0.7Bi0.2)TiO3-Bi(Mg0.5Zr0.5)O3 Lead-Free Ceramics and Potential for High-Temperature Capacitors

Xi Kong,Letao Yang,Zhenxiang Cheng,Shujun Zhang

DOI: https://doi.org/10.3390/ma13010180

IF: 3.4

2020-01-01

Materials

Abstract:Due to the enhanced demand for numerous electrical energy storage applications, including applications at elevated temperatures, dielectric capacitors with optimized energy storage properties have attracted extensive attention. In this study, a series of lead-free strontium bismuth titanate based relaxor ferroelectric ceramics have been successfully synthesized by high temperature solid-state reaction. The ultrahigh recoverable energy storage density of 4.2 J/cm3 under 380 kV/cm, with the high efficiency of 88%, was obtained in the sample with x = 0.06. Of particular importance is that this ceramic composition exhibits excellent energy storage performance over a wide work temperature up to 150 °C, with strong fatigue endurance and fast discharge speed. All these merits demonstrate the studied ceramic system is a potential candidate for high-temperature capacitors as energy storage devices.
Superior Energy Storage Performance of BiFeO3-BaTiO3-CaHfO3 Lead-Free Ceramics

Jianwei Zhao,Hongtian Li,Yuxiao Du,Xiaoxin Chen,Hailan Qin,Jinming Wang,Tingnan Yan,Shuhui Yu,Yongming Hu,Dawei Wang

DOI: https://doi.org/10.1039/d4ta00022f

IF: 11.9

2024-01-01

Journal of Materials Chemistry A

Abstract:Lead-free ceramics have received considerable research interest because of their environmentally friendly characteristics and superb performance in energy storage applications, which are critical for pulsed power electronic systems. In this work, we sintered a series of (0.90 - x)BiFeO3-xBaTiO(3)-0.10CaHfO(3) lead-free ceramics and comprehensively probed the crystallographic structure, grain morphology, electrical properties, etc., to assess their capability for use in energy storage applications. The 0.50BiFeO(3)-0.40BaTiO(3)-0.10CaHfO(3) ceramic achieved an ultrahigh recoverable energy storage density of 4.70 J cm(-3) and an outstanding energy conversion efficiency of 79% and can be considered an excellent material candidate for use in high-power energy storage devices.
Bi0.5Na0.5TiO3-based Lead-Free Ceramics with Superior Energy Storage Properties at High Temperatures

Peng Shi,Xiaopei Zhu,Xiaojie Lou,Bian Yang,Xudong Guo,Liqiang He,Qida Liu,Sen Yang,Xiaoxiao Zhang

DOI: https://doi.org/10.1016/j.compositesb.2021.108815

2021-01-01

Abstract:Dielectric capacitors with high energy storage and dielectric properties at high temperatures have significantly practical application in many fields. Lead-free ceramics of (1-x)(0.65Bi0.5Na0.5TiO3-0.35Bi0.2Sr0.7TiO3)-xBaSnO3 were prepared by a solid-state reaction method. It was found that the 0.8(0.65Bi0.5Na0.5TiO3-0.35Bi0.2Sr0.7TiO3)0.2BaSnO3 ceramic shows a large recoverable energy storage density (Wr) of 3.75 J/cm3 and efficiency (?) of 84.8% under 380 kV/cm along with outstanding power density of 38.73 MW/cm3 under 130 kV/cm at room temperature. Additionally, a high Wr of 3.21 J/cm3 and ? of 77% are achieved under a high electric field of 300 kV/cm at 100 ?C. When the temperature reaches 140 ?C, it still has a high Wr of 3.1 J/cm3 and ? of 72%. The outstanding energy storage performance at high temperatures can be explained by the enhancement of breakdown strength and the constructing of polar phase stability caused by the introduction of BaSnO3.
Enhanced low electric-field energy-storage performance in Ba0.9Sr0.1TiO3-Bi(Mg1/2Ti1/2)O-3 ceramics

Shihao Wang,Bijun Fang,Shuai Zhang,Xiaolong Lu,Jianning Ding

DOI: https://doi.org/10.2298/PAC2104410W

2021-01-01

Processing and Application of Ceramics

Abstract:Perovskite (1-x)Ba0.9Sr0.1TiO3-xBi(Mg1/2Ti1/2)O-3 (BST-BiMT-x) ceramics were prepared by sintering the corresponding powders synthesized by combining of solid state reaction method with citrate sol-gel and self-combustion techniques. Submicron grains morphology, high density and large resistivity were obtained in the BST-BiMT-x ceramics. In addition, the BST-BiMT-0.1 and BST-BiMT-0.075 ceramics exhibit ferroelectric hysteresis loops with slim shape which lead to enhanced energy-storage properties. The energy-storage density of these two ceramics increases almost linearly with increasing the applied electric filed. The energy-storage density and efficiency at 25 kV/cm of the BST-BiMT-0.1 and BST-BiMT-0.075 ceramics sintered at 1200 degrees C are 141.2 mJ/cm(3 )and 79.3%, and 158.1 mJ/cm(3) and 76.7%, respectively, surpassing many recently reported values for ferroelectric/antiferroelectric ceramics. The enhanced energy-storage density and efficiency under low electric field can be attributed to the slim polarization-electric field hysteresis loops, high density accompanied by submicron grains morphology and pure perovskite structure.
Bi‐modified SrTiO3‐based Ceramics for High‐temperature Energy Storage Applications

Xi Kong,Letao Yang,Zhenxiang Cheng,Shujun Zhang

DOI: https://doi.org/10.1111/jace.16844

IF: 4.186

2020-01-01

Journal of the American Ceramic Society

Abstract:Dielectric capacitors with high energy storage performance are in great demand for emerging advanced energy storage applications. Relaxor ferroelectrics are one type dielectric materials possessing high energy storage density and energy efficiency simultaneously. In this study, 0.9(Sr0.7Bi0.2)TiO3-0.1Bi(Mg0.5Me0.5)O-3 (Me = Ti, Zr, and Hf) dielectric relaxors are designed and the corresponding energy storage properties are investigated. The excellent recoverable energy density of 3.1 J/cm(3) with a high energy efficiency of 93% is achieved at applied electric field of 360 kV/cm for 0.9(Sr0.7Bi0.2)TiO3-0.1Bi(Mg0.5Hf0.5)O-3 (0.9SBT-0.1BMH) ceramic. High breakdown strength of 460 kV/cm in 0.9SBT-0.1BMH ceramic is obtained by Weibull distribution with satisfied reliability. In addition, 0.9SBT-0.1BMH shows outstanding thermal stability of energy storage performance up to 200 degrees C, with the variation being less than 5%, together with satisfying cycling stability and high charge-discharge rate, making the 0.9SBT-0.1BMH ceramic a potential lead-free candidate for high power energy storage applications at elevated temperature.
Realizing Excellent Energy Storage Performance and Fatigue Endurance in Sr0.7Sm0.2TiO3 Modified 0.67Bifeo3-0.33Batio3 Lead-Free Relaxor Ceramics

Shuo Liu,Wuwei Feng,Jinhong Li,Bin He,Meitang Liu,Zhidi Bao,Dengjie Luo,Changchun Zhao

DOI: https://doi.org/10.1016/j.jeurceramsoc.2022.08.055

IF: 5.7

2022-01-01

Journal of the European Ceramic Society

Abstract:Environmentally friendly BiFeO3-based capacitors have attracted great attention in energy storage applications. Herein, a large Wrec of 2.91 J/cm3 and a high eta of 85% were obtained under the electric field of 220 kV/cm in (1-x)(0.67BiFeO3-0.33BaTiO3)-xSr0.7Sm0.2TiO3 (BF-BT-xSST) ceramics at x = 0.30. The addition of SST facilitates to enhance the relaxor behavior and suppress the early polarization saturation of ceramics. The breakdown strength of BF-BT-xSST ceramics is enhanced due to the significantly decreased grain size and the increased band gap. More importantly, the BF-BT-0.30SST ceramic exhibits an excellent fatigue endurance (< 1.1%, after 105 fatigue cycles), which is superior to most of previous works. In addition, BF-BT-0.30SST ceramic also shows high thermal and frequency stability, and fast discharge rate (t0.9 < 0.16 mu s). We propose that the SST or a combination of SST and Sr0.7Bi0.2TiO3 is a better additive for the BF-based energy storage materials.
Achieving high energy storage performance and breakdown strength in modified strontium titanate ceramics

Mahmoud S. Alkathy,Fabio L. Zabotto,Flavio Paulo Milton,J. A. Eiras

DOI: https://doi.org/10.1007/s10854-022-08455-8

2022-06-08

Abstract:Lead-free ceramic capacitors with attractive properties such as their environmental friendliness, superior energy density, fast charge and discharge rate, and superior stability have recently received increased attention to meet liber market demands for energy storage devices in low consumption systems. However, overcoming its relatively low energy storage capacity is becoming extremely important. Based on this task, La 3+ and Li + co-doped SrTiO 3 ceramics are fabricated by a solid-state reaction method. The effect of La 3+ and Li + contents on the structural, microstructure, dielectrics, and energy storage properties of SrTiO 3 ceramics are systematically studied. XRD confirmed the phase structure along with Rietveld refinement studies. The morphological structure is studied using SEM. Through X-ray photoelectron spectroscopy spectra, the chemical composition and the chemical state of Sr (1− x ) (Li 0.50 La 0.50 ) x TiO 3 (SLLT x ); (0 ≤ x ≤ 8%) ceramics are studied. The energy storage properties are theoretically estimated by integrating the polarization versus electric field P-E hysteresis loop. The results show an increase in La 3+ and Li + content ( x ), resulting in enhanced dielectric breakdown strength, and maximum polarization yields a higher energy storage density. In the sample with x = 8%, it is found that the energy density is 2.455 J/cm 3 and the energy efficiency is more than 90%. The further improvement in dielectric constant, dielectric breakdown strength, enhanced energy storage densities and the energy efficiency maintained > 90% make these materials commercially promising for energy storage device capacitors for a wide range of energy storage applications.

engineering, electrical & electronic,materials science, multidisciplinary,physics, condensed matter, applied
Enhanced recoverable energy storage density and efficiency in (1 − x)Ba0.85Ca0.15Zr0.1Ti0.9O3-xSrTiO3-MnO2 lead-free ceramics

Wenjin Yang,Fengzhen Huang,LiHuai Shu,YuLong Yang,Baolian Gong,Xiaomei Lu,Jinsong Zhu

DOI: https://doi.org/10.1039/d2tc00056c

IF: 6.4

2022-01-01

Journal of Materials Chemistry C

Abstract:Realizing enhanced energy storage performance by introducing SrTiO3 (ST) to Ba0.85Ca0.15Zr0.1Ti0.9O3 (BCZT).
Enhanced energy storage density and efficiency in lead-free Bi(Mg1/2Hf1/2)O3-modified BaTiO3 ceramics

Zhi-Gang Liu,Ming-Ding Li,Zhen-Hua Tang,Xin-Gui Tang

DOI: https://doi.org/10.1016/j.cej.2021.129379

IF: 15.1

2021-08-01

Chemical Engineering Journal

Abstract:Recently, the energy crisis become more and more intense and people are gradually committed to new energy storage devices to ease the pressure. Composite energy storage ceramics are extensively explored for its splendid dielectric/ferroelectric performances. In this research, it is the first time that the (1 − x)BaTiO3-xBi(Mg1/2Hf1/2)O3 (BT-BMH) lead-free ferroelectric ceramics are prepared by traditional solid-state method. By introducing BMH into BT lattice, normal ferroelectric can be induced to relaxor ferroelectric. Especially in the case of high BMH doping (x ≥ 0.05), the relaxation dispersion behaviors are more obvious. As addition BMH goes up, the hysteresis loops gradually shrink to sublinear, which is conducive to the high efficiency of energy storage performance of ceramic capacitors. Meanwhile, the recoverable energy of BT–BMH (x = 0.1) ceramics can reach 3.38 J/cm3 with efficiency of nearly 87% at a relatively low electric field of 240 kV/cm. In addition, the optimized ceramic samples possess excellent stability of variable temperatures and frequencies, showing the potential for storage application.

engineering, chemical, environmental
(Ba,Sr)TiO 3 –Bi(Mg,Hf)O 3 Lead-Free Ceramic Capacitors with High Energy Density and Energy Efficiency

Xi Kong,Letao Yang,Zhenxiang Cheng,Gemeng Liang,Shujun Zhang

DOI: https://doi.org/10.1021/acsaem.0c02320

IF: 6.4

2020-12-07

ACS Applied Energy Materials

Abstract:Dielectric capacitors with high energy storage performance have been actively studied for emerging applications. In this work, a series of environmental friendly lead-free relaxor ferroelectric ceramics, (1 – x)(Ba0.75Sr0.25)TiO3–xBi(Mg0.5Hf0.5)O3 with 0 ≤ x ≤ 0.5 [abbreviated as (1 – x)BST–xBMH], were synthesized by a high-temperature solid-state reaction method. The perovskite structure without any secondary phase can be obtained in samples with x ≤ 0.4. As the BMH content increases, the polarization–electric field (P–E) loop becomes slim and slanted. A large recoverable energy storage density of 4.3 J/cm3 and high energy efficiency of 92% were achieved simultaneously in 0.6BST–0.4BMH at 390 kV/cm. The fine grain morphology with minimal porosity and the high conductivity activation energy were responsible for the enhanced breakdown strength. Of particular importance is that the 0.6BST–0.4BMH ceramic shows excellent temperature stability and cycling reliability with energy density variations below 3 and 4%, respectively. In addition, the 0.6BST–0.4BMH ceramic possesses fast discharge time (∼0.59 μs) with a high power density of 3.5 MW/cm3. All these merits reveal that the lead-free 0.6BST–0.4BMH relaxor ceramic is a promising candidate for high-temperature and high-power energy storage capacitor applications.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Achieving High Energy Storage Density and Efficiency Simultaneously in Sr(Nb0.5Al0.5)O3 Modified BiFeO3 Based Lead-Free Ceramics

Shuo Liu,Wuwei Feng,Jinhong Li,Changchun Zhao,Cheng Hu,Bin He,Zhidi Bao,Xuezhu Luan

DOI: https://doi.org/10.1016/j.cej.2022.138916

2022-01-01

SSRN Electronic Journal

Abstract:Environmentally friendly BiFeO3-based capacitors have attracted great attention in energy storage applications. Via a design of crossover relaxor ferroelectric state with high maximum polarization and small remanent polarization at moderate electric fields, a large W-rec of 3.95 J/cm(3) and an excellent of 85.9 % was obtained in 0.85 (0.67BiFeO(3)-0.33BaTiO(3))-0.15Sr(Nb-0.5 Al-0.5)O-3 crossover relaxor ceramic. The addition of Sr(Nb0.5Al0.5)O-3 facilitates to the formation of crossover relaxor ferroelectric state and suppresses the early polarization saturation. The breakdown strength of Sr(Nb0.5Al0.5)O-3 modified ceramics is enhanced due to the significantly decreased grain size and the increased band gap. More importantly, the X = 0.15 ceramic exhibits an excellent thermal stability (25-110 degrees C), frequency stability (1-300 Hz), fatigue endurance (after 10 5 cycles), and fast discharge rate (t(0.9) similar to 0.108 mu s) at 140 kV/cm. These results indicate that the BF-BT-0.15SNA ceramic is a promising dielectric energy storage material.
(Na0.5Bi0.5)0.7Sr0.3TiO3 modified by Bi(Mg2/3Nb1/3)O3 ceramics with high energy-storage properties and an ultrafast discharge rate

Ying Lin,Da Li,Miao Zhang,Haibo Yang

DOI: https://doi.org/10.1039/c9tc06218a

IF: 6.4

2020-01-01

Journal of Materials Chemistry C

Abstract:Novel (Na0.5Bi0.5)0.7Sr0.3TiO3-based lead-free ceramics with vastly improved energy-storage properties for high power system applications.
Improved Energy Storage Density performance of the (1-x) [0.88BaTiO3–0.12Bi(Li0.5Nb0.5)O3]-x(0.8BaTiO3–0.2SrTiO3) Lead-Free Ceramics

Jia-Jia Ren,Di Zhou,Wen-Bo Li,Da Li,Yan Guo,Tao Zhou,Shi-Kuan Sun

DOI: https://doi.org/10.1016/j.materresbull.2023.112157

IF: 5.6

2023-05-01

Materials Research Bulletin

Abstract:Recently, dielectric ceramic materials have been widely explored for high-power capacitors applications. However, it is still challenged for capacitors to enhance the energy density and efficiency. Here, the (1-x)[0.88BaTiO3–0.12Bi(Li 0.5Nb 0.5)O3]-x(0.8BaTiO3–0.2SrTiO3) (0.05 ≤ x ≤ 0.20) ceramics were designed to improve both dielectric temperature stability and breakdown strength. Influence of composition and phase structure on dielectric properties were studied in detail. Improvement of both dielectric properties and energy storage performance was achieved in this work. The 0.95[0.88BaTiO3–0.12Bi(Li 0.5Nb 0.5)O3]-0.05(0.8BaTiO3–0.2SrTiO3) ceramic shows the best performance, with an energy storage density up to 2.88 J/cm3 (We ∼ 2.51 J/cm3) and a high efficiency ∼ 86.81% under 320 kV/cm. This work not only provides key materials for the next generation of high-end energy storage capacitors, but also suggests a different route for optimizing the performance of other relaxor ferroelectrics.

materials science, multidisciplinary
Bismuth Ferrite-Modified Lead-Free Ceramics with Reduced Sintering Temperature and Improved Energy Storage Properties

Xi Kong,Letao Yang,Zixi Luo,Yiqian Liu,Shun Lan,Bingbing Yang,Fanqi Meng,Weibin Ren,Xinyue Zhang,Jinghan Cai,Yuan-Hua Lin,Jinming Guo,Ce-Wen Nan

DOI: https://doi.org/10.1063/5.0145299

IF: 4

2023-01-01

Applied Physics Letters

Abstract:Dielectric ceramics with high polarization and low sintering temperature are important for high-performance and low-cost multilayer ceramic capacitors (MLCCs). Herein, BiFeO3 was added to a lead-free composition 0.48BaTiO(3)-0.4Bi(Mg0.5Hf0.5)O-3-0.12SrTiO(3) to lower the sintering temperature and increase the polarization simultaneously. As a result, a low sintering temperature of 950 degrees C and high comprehensive energy storage properties with a recoverable energy density W-rec of 5.7 J/cm(3) and an energy efficiency eta of 92% at 450 kV/cm were achieved. Together with the good temperature stability and cycling stability of Wrec and g, the ceramics exhibit great potential in the energy storage MLCCs with low-cost Ag-Pd electrodes with a high Ag content.
A Lead Free Relaxation and High Energy Storage Efficiency Ceramics for Energy Storage Applications

Haibo Yang,Fei Yan,Ying Lin,Tong Wang,Li He,Fen Wang

DOI: https://doi.org/10.1016/j.jallcom.2017.03.261

IF: 6.2

2017-01-01

Journal of Alloys and Compounds

Abstract:In the present work, ternary solid solution ceramics of the (1-x)SrTiO3-x(0.65BaTiO(3)-0.35Bi(0.5)Na(0.5)TiO(3)) (STB100x) were designed and fabricated using a conventional solid-state sintering method. The phase structure, microstructure, dielectric property, relaxation property, ferroelectric property and energy storage property were systematically investigated. The addition of 0.65BaTiO(3)-0.35Bi(0.5)Na(0.5)TiO(3) (BTBNT) could enhance the saturated polarization of the ceramics obviously. All the samples show a slim P-E hysteresis loop, and the sample with x = 0.3 exhibits a high energy storage density of 1.40 J/cm(3) and an energy storage efficiency more than 90%. These results indicate that the STB100x ceramics may be a promising lead free materials for high energy storage density capacitors. (C) 2017 Elsevier B.V. All rights reserved.
(Ba,Sr)TiO3-Bi(Mg,Hf)O3 Lead-Free Ceramic Capacitors with High Energy Density and Energy Efficiency

Xi Kong,Letao Yang,Zhenxiang Cheng,Gemeng Liang,Shujun Zhang

DOI: https://doi.org/10.1021/acsaem.0c02320

IF: 6.4

2020-01-01

ACS Applied Energy Materials

Abstract:Dielectric capacitors with high energy storage performance have been actively studied for emerging applications. In this work, a series of environmental friendly lead-free relaxor ferroelectric ceramics, (1 - x)(Ba0.75Sr0.25)TiO3-xBi(Mg0.5Hf0.5)O-3 with 0 <= x <= 0.5 [abbreviated as (1 - x)BST-xBMH], were synthesized by a high-temperature solid-state reaction method. The perovskite structure without any secondary phase can be obtained in samples with x <= 0.4. As the BMH content increases, the polarization-electric field (P-E) loop becomes slim and slanted. A large recoverable energy storage density of 4.3 J/cm(3) and high energy efficiency of 92% were achieved simultaneously in 0.6BST-0.4BMH at 390 kV/cm. The fine grain morphology with minimal porosity and the high conductivity activation energy were responsible for the enhanced breakdown strength. Of particular importance is that the 0.6BST-0.4BMH ceramic shows excellent temperature stability and cycling reliability with energy density variations below 3 and 4%, respectively. In addition, the 0.6BST-0.4BMH ceramic possesses fast discharge time (similar to 0.59 mu s) with a high power density of 3.5 MW/cm(3). All these merits reveal that the lead-free 0.6BST-0.4BMH relaxor ceramic is a promising candidate for high-temperature and high-power energy storage capacitor applications.Y
Enhanced Energy Storage Properties of BaTiO3-Bi0.5Na0.5TiO3 Lead-Free Ceramics Modified by SrY0.5Nb0.5O3

Xiaoyu Liu,Haibo Yang,Fei Yan,Yi Qin,Ying Lin,Tong Wang

DOI: https://doi.org/10.1016/j.jallcom.2018.11.106

IF: 6.2

2018-01-01

Journal of Alloys and Compounds

Abstract:In this work, a novel lead-free relaxor-ferroelectric ceramics of (1-x)(0.65BaTiO(3)-0.35Bi(0.5)Na(0.5)TiO(3))-xSrY(0.5)Nb(0.5)O(3) ((1-x)BTBNT-xSYN x = 0.02-0.12), was designed and prepared by the conventional solid state reaction method. The results show that all of the sintered samples have a perovskite structure. The Curie Temperature (T-c) moves to the low temperature side which causes the high dielectric constant at room temperature, and the ferroelectric hysteresis loop becomes slimmer and slimmer with increasing the content of SYN. Meanwhile, the optimal energy storage properties can be obtained in 0.92BTBNT-0.08SYN ceramic with an impressive discharged energy density (W-rec) of 1.36 J/cm(3) under 152 kV/cm, and the charge-discharge efficiency reaches 74.3%. Therefore, all these results indicate that (1-x)BTBNT-xSYN lead-free ceramics can be applied for pulsed power capacitors. (C) 2018 Elsevier B.V. All rights reserved.
Significantly Improvement of Comprehensive Energy Storage Performances with Lead-free Relaxor Ferroelectric Ceramics for High-temperature Capacitors Applications

Haoran Ye,Fan Yang,Zhongbin Pan,Di Hu,Xujiao Lv,Hanxi Chen,Feifei Wang,Jiasheng Wang,Peng Li,Jianwen Chen,Jinjun Liu,Jiwei Zhai

DOI: https://doi.org/10.1016/j.actamat.2020.116484

IF: 9.4

2021-01-01

Acta Materialia

Abstract:Next-generation advanced electronic markets demand high energy-storage properties dielectric materials that can operate efficiently under elevated temperatures. Here, the Sr0.85Bi0.1TiO3 modified Bi0.4465Na0.4465Ba0.057La0.05TiO3 ceramics ((1-x)BNBLT-xSBT) are designed to achieve excellent comprehensive energy storage performances. The phase field simulations and experimental results indicate that the SBT doping into BNBLT ceramics could effectively decrease grain size, resulting in enhancement breakdown strength. Consequently, excellent comprehensive performances via a superior balance between recoverable energy density (Wrec ∼ 4.55 J/cm3) and efficiency (η > 90%) values have been realized in x=0.25 compositions. The corresponding ceramics exhibit impressive temperature stability (20∼200 °C), fatigue endurance (105 st), and frequency stability (1∼1000 Hz). More importantly, the BNBLT-0.25SBT ceramic shows a high power density (38.1 MW/cm3) and a record discharge rate (45 ns). Therefore, this work will provide a simple and effective method to develop a new category of dielectric capacitors with superior energy-storage performances over an extended temperature range.

materials science, multidisciplinary,metallurgy & metallurgical engineering

Bi(Mg0.5Hf0.5)O3-modified SrTiO3 Lead-Free Ceramics for High-Temperature Energy Storage Capacitors

Ultrahigh Energy Storage Properties in (Sr 0.7 Bi 0.2 )TiO 3 -Bi(Mg 0.5 Zr 0.5 )O 3 Lead-Free Ceramics and Potential for High-Temperature Capacitors.

Ultrahigh Energy Storage Properties in (Sr0.7Bi0.2)TiO3-Bi(Mg0.5Zr0.5)O3 Lead-Free Ceramics and Potential for High-Temperature Capacitors

Ultrahigh Energy Storage Properties in (Sr<sub>0.7</sub>Bi<sub>0.2</sub>)TiO<sub>3</sub>-Bi(Mg<sub>0.5</sub>Zr<sub>0.5</sub>)O<sub>3</sub> Lead-Free Ceramics and Potential for High-Temperature Capacitors

Superior Energy Storage Performance of BiFeO3-BaTiO3-CaHfO3 Lead-Free Ceramics

Bi0.5Na0.5TiO3-based Lead-Free Ceramics with Superior Energy Storage Properties at High Temperatures

Enhanced low electric-field energy-storage performance in Ba0.9Sr0.1TiO3-Bi(Mg1/2Ti1/2)O-3 ceramics

Bi‐modified SrTiO3‐based Ceramics for High‐temperature Energy Storage Applications

Realizing Excellent Energy Storage Performance and Fatigue Endurance in Sr0.7Sm0.2TiO3 Modified 0.67Bifeo3-0.33Batio3 Lead-Free Relaxor Ceramics

Achieving high energy storage performance and breakdown strength in modified strontium titanate ceramics

Enhanced recoverable energy storage density and efficiency in (1 − <i>x</i>)Ba<sub>0.85</sub>Ca<sub>0.15</sub>Zr<sub>0.1</sub>Ti<sub>0.9</sub>O<sub>3</sub>-<i>x</i>SrTiO<sub>3</sub>-MnO<sub>2</sub> lead-free ceramics

Enhanced energy storage density and efficiency in lead-free Bi(Mg1/2Hf1/2)O3-modified BaTiO3 ceramics

(Ba,Sr)TiO 3 –Bi(Mg,Hf)O 3 Lead-Free Ceramic Capacitors with High Energy Density and Energy Efficiency

Achieving High Energy Storage Density and Efficiency Simultaneously in Sr(Nb0.5Al0.5)O3 Modified BiFeO3 Based Lead-Free Ceramics

(Na<sub>0.5</sub>Bi<sub>0.5</sub>)<sub>0.7</sub>Sr<sub>0.3</sub>TiO<sub>3</sub> modified by Bi(Mg<sub>2/3</sub>Nb<sub>1/3</sub>)O<sub>3</sub> ceramics with high energy-storage properties and an ultrafast discharge rate

Improved Energy Storage Density performance of the (1-x) [0.88BaTiO3–0.12Bi(Li0.5Nb0.5)O3]-x(0.8BaTiO3–0.2SrTiO3) Lead-Free Ceramics

Bismuth Ferrite-Modified Lead-Free Ceramics with Reduced Sintering Temperature and Improved Energy Storage Properties

A Lead Free Relaxation and High Energy Storage Efficiency Ceramics for Energy Storage Applications

(Ba,Sr)TiO<sub>3</sub>-Bi(Mg,Hf)O<sub>3</sub> Lead-Free Ceramic Capacitors with High Energy Density and Energy Efficiency

Enhanced Energy Storage Properties of BaTiO3-Bi0.5Na0.5TiO3 Lead-Free Ceramics Modified by SrY0.5Nb0.5O3

Significantly Improvement of Comprehensive Energy Storage Performances with Lead-free Relaxor Ferroelectric Ceramics for High-temperature Capacitors Applications