Abstract:Magnesium alloy components are mainly used in aerospace and automotive fields, but poor deformation ability at room temperature restricts their application in other industries. To address this issue, electrically-assisted technology is employed to enhance plasticity of alloys. However, conventional method weaken strength and intensify surface oxidation of such alloys because of prolonged action of current. In view of the above, pre-deformation (PF) treatment in combination with transient induced pulse current treatment (TIPCT) is proposed in the present work so as to balance between plasticity recovery and strength of AZ31B alloy. The results show that the total elongation of PF sample and the corresponding TIPCT specimen first increases and then decreases with the increase in PF percentage under the same voltage. At the same PF percentage, the total elongation of PF and TIPCT specimens also presents the same trend as the voltage increases. At the same time, the total elongation in PF and TIPCT specimens is greater than that of the as-received sample. The maximum total elongation is achieved at the PF percentage of 16 % and the voltage of 6 kV, being 35 % higher than that in the as-received sample. The improvement in total elongation is due to activation of more non-basal dislocations induced by TIPCT and the appropriate amount of microcracks generated by PF. In addition, the TIPCT process also improves the yield strength even if the PF percentage and voltage are changed. Besides that, the work hardening induced by PF treatment and instantaneous action of TIPCT process are the key factors enhancing yield strength. Moreover, comprehensive mechanical properties of TIPCT sample are found to outperform those after direct pulse current treatment (DPCT) under the same PF percentage. Therefore, the proposed composite process provides a feasible scheme to enhance strength and elongation of Mg sheets.

Combination of eddy current and heat treatment for crack healing and mechanical-property improvement in magnesium alloy tube

Microcrack Healing in Non-Ferrous Metal Tubes Through Eddy Current Pulse Treatment.

Restoration of Fatigue Damage in Steel Tube by Eddy Current Treatment

Effect of Heat Treatment on Microstructure and Mechanical Properties of Mg-5Zn-1Mn Alloy Tube

Healing of Fatigue Crack in 1045 Steel by Using Eddy Current Treatment

OS0111 Healing of Fatigue Crack Treated by Surface-Activated Pre-Coating and Controlling High-Density Electric Current Field

Influence of Heat Treatment on the Evolution of Microstructure and Mechanical Properties of Mg-7Gd-5Y-0.6Zn-0.8Zr Magnesium Alloy

Near-in-situ investigation of surface crack healing and strengthening mechanism of Ti-43.5Al-4Nb-1Mo-0.1B alloy by novel electroshock treatment

Microstructural Effect and Material Homogenization of Thermal-Hydroforming Magnesium Alloy Tubes

Effects Of Ecap And Annealing Treatment On The Microstructure And Mechanical Properties Of Mg-1y (Wt. %) Binary Alloy

Effect of Solution Treatment on Microstructure Evolution and Mechanical Properties of Mg-6.0Zn-0.6Y-0.5Zr Alloy Processed by Equal Channel Angular Extrusion

Plastic recovery and strength enhancement of pre-deformed AZ31B magnesium alloy using transient strong pulse current

Effect of High Density Current Pulses on Microstructure and Mechanical Properties of Dual-Phase Wrought Superalloy

Effects of Heat Treatment on Microstructure and Mechanical Properties of Extruded AM50+xCa Magnesium Alloys

Microstructure Evolution and Mechanical Properties of AZ80 Mg Alloy during Annular Channel Angular Extrusion Process and Heat Treatment

Evolution of the microstructure and properties of a Cu–Cr-(Mg) Alloy upon thermomechanical treatment

Improved mechanical properties of Mg-1Gd alloy by cold rolling and electropulse treatment

Study on the Effect of the ECAP Deformation on the Organization and Properties of the Extruded Mg-Sn-Al Alloys

Precipitation behaviors and mechanical properties of a solution-treated Mg-Gd-Nd-Zn-Zr alloy during equal-channel angular pressing process

Effect of Electropulsing Treatment on Solid Solution Behavior of an Aged Mg Alloy AZ61 Strip

Effects of Heat Treatment on Microstructure and Mechanical Properties of Rolled AM50+xCa Magnesium Alloys