Transmission Spectrum and Four-Wave Mixing in Three-Cavity Hybrid Optomechanical System
Qinghong Liao,Haiyan Qiu,Fu Yu,Min Xiao
DOI: https://doi.org/10.3788/CJL221046
2023-01-01
Abstract:Objective The rapid development of cavity optomechanical systems has attracted extensive attention, and these systems are widely used in quantum information and precision measurement. In recent years, three -cavity optomechanical systems have attracted considerable attention. Compared with the single -mode optomechanical system, the multiple -mode system provides significantly higher flexible controllability. Furthermore, optomechanically induced transparency and four -wave mixing have been research hotspots in different optomechanical systems. For example, the four -wave mixing in a hybrid optomechanical system is theoretically investigated, which has important implications for the nonlinear optical properties. It is of great significance for theoretically exploring the transmission spectrum and four -wave mixing in a three -cavity optomechanical system.Methods The hybrid optomechanical system consists of a microwave cavity a with resonance frequency omega a and an optical cavity c1 with resonance frequency omega c1, which are coupled to a common mechanical resonator b, while an optical cavity c2 with resonance frequency omega c2 is coupled to the optical cavity c1. A strong pump laser beam Ee with frequency omega e is applied to the microwave cavity a. A weak probe laser beam Ep with frequency omega p and a strong pump laser beam Eo with frequency omega o are applied to the optical cavity c1 simultaneously. In the rotating frame of the pump fields with frequency omega e and omega o, the whole Hamiltonian of the system is obtained. According to the Heisenberg equation and making the ansatz, we finally obtain the transmission spectrum and the four -wave mixing spectrum intensity. Then, we investigate how the evolutions of the transmission spectrum and the four -wave mixing spectrum are affected by the coupling strength and the frequency of the mechanical resonator.Results and Discussions When the optical cavity c2 is absent in the hybrid optomechanical system (J=0), the transmission spectrum of the probe field shows a Lorentzian line shape. However, when J not equal 0, the Lorentzian peak splits into two symmetrical peaks and a transparent window occurs (Fig. 2). It is clear that with the increase in the coupling strength from J=0.5 kappa o to J=2 kappa o, the distance between the peaks increases, and the peak value of the transmission spectrum of the probe field also increases (Fig. 3). We depict the variation of the four -wave mixing spectrum with the detuning of the probe field -cavity field Delta p for J=0, 0.5 kappa o, kappa o, 2 kappa o when omega m=27c x 5.6 MHz. In the case of Delta c1=Delta c2=Delta a=0, when J=0, the four -wave mixing spectrum has three peaks. A Lorentzian peak locates at Delta p=0 and two splitting peaks locate on both sides of the Lorentzian peak [Fig. 4(a)]. With the choice of J not equal 0, a significant change in the four -wave mixing spectrum can be observed. The Lorentzian peak splits into two peaks. As the coupling strength J increases, the peak value decreases greatly and the distance between the peaks gradually increases [Figs. 4(b)-(d)]. Next, we study how the evolution of the four -wave mixing spectrum is affected by the frequency of the mechanical resonator while the optical cavity c2 is not in the hybrid optomechanical system (J=0). It can be seen that as the frequency of the mechanical resonator increases, the peak value of the four -wave mixing spectrum gradually decreases. Further, the peaks on both sides of the four -wave mixing spectrum located at +/-Delta p just correspond to the frequency omega m of the mechanical resonator (Fig. 5). Moreover, we investigate the four wave mixing spectrum as a function of the detuning Delta p for the frequencies of mechanical resonator of omega m=2 7c x4.6 MHz, omega m=2 7c x 5.6 MHz, and omega m=27c x6.6 MHz when J= kappa o. As the frequency of the mechanical resonator increases, the peak value and the distance between the two symmetrical splitting peaks in the middle decrease. The positions of the peaks on both sides exactly correspond to the three different frequencies of the mechanical resonator. The results show that the four -wave mixing can be tuned by the frequency of the mechanical resonator (Fig. 6).Conclusions We investigate the optomechanically induced transparency and four -wave mixing in a hybrid optomechanical system composed of two optical cavities, a microwave cavity, and a mechanical resonator. When the microwave cavity is driven to the red sideband and the two optical cavities are driven to the blue sideband, the optomechanically induced transparency can be changed by changing the coupling strength between the two optical cavities. Furthermore, the four -wave mixing spectrum can be modulated by controlling the coupling strength between the two optical cavities and by changing the frequency of the mechanical resonator during resonant detuning Delta p = 0. At the same time, a nonlinear optical method for measuring the frequency of a mechanical resonator is provided. The positions of the peaks on both sides of the four -wave mixing spectrum correspond exactly to the frequency of the mechanical resonator. These results have important significance and application prospects in quantum sensing and quantum information processing.