Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

Synergistic effect of additives and blend on sulfur retention, NO release and ash fusibility during combustion of biomass briquettes

Combustion Characteristics, Kinetics, SO2 and NO Release of Low-Grade Biomass Materials and Briquettes

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Experiment research on utilization of particle biomass fuel in sintering process

Influence of phosphorus based additives on nitrogen and sulfur pollutants emissions during densified biochar combustion

[The role of additives in bio-mass coal briquette on sulfur retention enhancement]

Synergistic effect and volatile emission characteristics during co-combustion of biomass and low-rank coal

Thermodynamics and synergistic effects on the co-combustion of coal and biomass blends

Impact of Dilution Ratio and Burning Conditions on the Number Size Distribution and Size-Dependent Mixing State of Primary Particles from Domestic Solid Fuel Burning

Experimental and Numerical Investigation of the Combustion Characteristics and NO Emission Behaviour During the Co-Combustion of Biomass and Coal

Biocoal Briquettes Combusted in A Household Cooking Stove: Improved Thermal Efficiencies and Reduced Pollutant Emissions

Evaluating the Impact of Wood Sawdust and Peanut Shell Mixing Ratio on Co-Combustion Performance

Characteristics of Biomass Charcoal Briquettes and Pollutant Emission Reduction for Sulfur and Nitrogen During Combustion

CO2 and air pollutant emissions from bio-coal briquettes

Study on the Co-combustion Characteristics and Synergistic Effect of Semi-Coke and Dust Coal Produced from Biomass Briquette in Fluidized Bed Gasification

An Experimental Study On Biomass Coal Briquetting Process

Parameter Optimization of Waste Coal Briquetting and Particulate Matter Emissions Test During Combustion: A Case Study.

Combustion properties improvement and economic evaluation of charcoal briquettes from mixed agricultural waste biomass

Control of Pollutants in the Combustion of Biomass Pellets Prepared with Coal Tar Residue As a Binder

Influence of Molding Technology on Thermal Efficiencies and Pollutant Emissions from Household Solid Fuel Combustion during Cooking Activities in Chinese Rural Areas

Study on the feasibility and co-combustion mechanism of mixed injection of biomass hydrochar and anthracite in blast furnace