Abstract:In the process of non-isothermal deformation of titanium alloy, the microstructure evolution is very complicated, which has direct effect on the properties of the titanium alloy. This study examines the effects of pure cooling and coupled deformation and cooling at the initial temperature of 940 °C and the cooling rate of 5,50 °C/s, and the strain rate of 0.1, 10s −1 respectively, on the microstructure evolution of Ti–6Al-2.5Mo-1.5Cr-0.5Fe-0.3Si alloy (TC6) were investigated. The microstructure after cooling was characterised, and the mechanism of non-isothermal deformation on microstructure evolution and the mechanism of secondary α phase ( α s ) precipitation were revealed. The results show that the secondary α phase precipitates in large quantities after cooling to a certain temperature, and the secondary precipitated has an obvious inhibiting effect on the diffusion growth of the primary α phase ( α p ). Secondary α phases can be divided into lamellar and equiaxial types. When the temperature drops sharply, the fine secondary α phase can be precipitated directly from the β matrix. Due to the large number of dislocations generated by the deformation, many small secondary α phases can be generated during the rapid cooling process. The orientation relationship between α phase and β matrix is destroyed by the deformation, resulting in a weakening of the anisotropy, so that the secondary α phase remains equiaxial during the precipitation process.

Effect of Cooling Rate on Microstructure and Deformation Behavior of Ti-based Metallic Glassy/crystalline Powders

Differences in Crystallisation Behaviours During Cooling and Post-Heating Processes of Ti Based Metallic Powders

Cooling Rate Effect of Nanomechanical Response for A Ti-Based Bulk Metallic Glass

Metastable Nanocrystallization Behavior of Ti-based Metallic Glassy Powders During Post-Heating

Temperature Influence on Sintering with Concurrent Crystallization Behavior in Ti-Based Metallic Glassy Powders

Cooling Rate Effects on the Microstructure and Phase Formation in Zr51Cu20.7Ni12Al16.3bulk Metallic Glass

Cooling rate effects on the microstructure and phase formation in Zr51Cu20.7Ni12Al16.3 bulk metallic glass

Effect of Rolling Deformation on the Microstructure of Bulk Cu60Zr20Ti20 Metallic Glass and Its Crystallization

Effect of Ti addition on supercooled liquid region and glass forming ability of bulk amorphous Zr60Cu20Ni10-xAl10Tix alloys

Effect of deformation and cooling on non-equilibrium microstructure evolution and phase-transition mechanism of Ti–6Al-2.5Mo-1.5Cr-0.5Fe-0.3Si

Nanoindentation study of Ti-based metallic glasses

Effect of Chemical Composition on the Thermoplastic Formability and Nanoindentation of Ti-Based Bulk Metallic Glasses

Microstructure of Cu 60 Zr 20 Ti 20 Bulk Metallic Glass Rolled at Different Strain Rates

Microstructure evolution of the rapidly solidified alloy powders and composite powders

Deformation and Crystallization of a Zr41.2Ti13.8Cu12.5Ni10Be22.5 Bulk Metallic Glass in the Supercooled Liquid Region

Mechanism for Microstructural Evolution Induced by High Temperature Deformation in Zr-based Bulk Metallic Glasses

Influence of Substitution of Cu by Ni on the Crystallization Kinetics of TiZrHfBeCu High Entropy Bulk Metallic Glass

Effect of Cooling Rates on Microstructures Evolution and Nanohardness of Rapidly Solidified Ti-48Al-4Cr Alloy

Improved Tensile Ductility by Severe Plastic Deformation for Nano-Structured Metallic Glass.

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Crystallization Behavior of a Series of Zr-based Metallic Glasses