Abstract:Numerically simulated specimens with a three-dimensional pre-existing surface flaw are subjected to stress waves until failure via finite element analysis. Different types of cracks are reproduced, including wing cracks, anti-wing cracks, shell-like cracks and spalling fractures. The effects of different flaw dip angles on the initiation and propagation of wing cracks, anti-wing cracks and shell-like cracks are analysed under dynamic loading conditions. The numerical simulation results indicate that the dip angle of the flaw plays an important role in the crack behaviour and failure patterns of flawed specimens under dynamic loading. Wing cracks and anti-wing cracks emerge and present similar crack propagation patterns on the surface of the specimen when the pre-existing flaw dip angle is less than 60 degrees. In contrast, only wing cracks appear in specimens with flaw dip angles of 75 degrees and 90 degrees. Shell-like cracks are reproduced inside of the specimens in all cases except the specimen with a flaw dip angle of 90 degrees. In addition, the further propagation of shell-like cracks proceeds after the wing and anti-wing cracks stop propagating. Meanwhile, the numerical simulation also identifies the acoustic emission (AE) counts and energy of the specimen, which are closely related to the flaw dip angle during the dynamic failure process. The flaw dip angle has a slight effect on the dynamic strength of the specimens. Furthermore, the cracking patterns of specimens with a single pre-existing flaw under dynamic and static loading conditions are compared based on numerical investigations. Dynamic loading can produce more cracks and lead to more complex cracking behaviour. Moreover, loading rates can significantly influence crack propagation patterns and AE characteristics of rock specimens. Under high loading rates, the specimens fragment more efficiently. In addition, for specimens subjected to high loading rates, the more shear fractures occur, the greater the cumulative AE energy and the fewer the AE counts. Finally, heterogeneity also plays an important role in the distribution of micro-cracks in the material and the crack propagation patterns. Crack branching occurs in relatively heterogeneous rocks, which affects the further propagation of cracks initiated early. The stress concentration zone is not the only decisive factor and may be replaced by the degree of heterogeneity to determine the crack initiation and propagation. The results of this study can provide a valuable reference for studies on the failure process of heterogeneous brittle materials under dynamic loading.

Laboratory study of interaction between a circular hole defect and mode I moving crack

Influence of Circular Hole Defect on Dynamic Crack Propagation Behavior under Impact Loads

Effects of a Circular Hole on the Propagation Behavior of Double Running Cracks under Impact Loading

Study the effect of circular hole on dynamic fracture properties of cracked PMMA specimen under impact loads

Crack arrest characteristics and dynamic fracture parameters of moving cracks encountering double holes under impact loads

Effect of Holes on Dynamic Crack Propagation under Impact Loading

Investigation of the interaction mechanism of two dynamic propagating cracks under blast loading

Initiation and Propagation of a Single Internal 3D Crack in Brittle Material under Dynamic Loads

Connecting modes of two cracks under impact loads

Dynamic propagation behaviors of pure mode I crack under stress wave loading by caustics

Study of the defect-crack offset distance on the impact fracture behavior of plexiglass

Effect of Hole Relative Size and Position on Crack Deflection Angle of Repaired Structure

Study of the effect of lengths on the propagation mechanism of interconnected cracks under impact loads

Numerical Investigation of Dynamic Fracture in Rock Specimens Containing a Pre-Existing Surface Flaw with Different Dip Angles

The influence of circular cavity on the characteristics of dynamic crack propagation in rocks using a single notch triangle approach

Simultaneously Measuring Initiation Toughness of Pure Mode I and Mode II Cracks Subjected to Impact Loads

Experimental Study on Three‐Dimensional Internal Crack Propagation in Brittle Materials With Combined Defects

Fracture Mechanics Analysis of Mode-Ⅲ Radial Multi Cracks on the Edge of a HoleWith Surface Effects

The Dynamic Crack Propagation Behavior of Mode I Interlaminar Crack in Unidirectional Carbon/epoxy Composites

Investigation on Fracture Properties of Single-Flawed Tunnel Model under Medium-to-Low-Speed Impacts

Study on the mechanical behavior of crack propagation effect at the end of defect under explosive load