Real-time Myoelectric Control with an Arduino

Hancong Wu,Matthew Dyson,Kianoush Nazarpour

DOI: https://doi.org/10.1109/icecs49266.2020.9294944

2020-01-01

Abstract:This paper reports the design of a low-cost myoelectric system on the Arduino platform for real-time prosthetic control. It successfully controlled a commercial hand prosthesis to complete multiple grips with the direct controller and the abstract controller with a 250 ms response time.

What problem does this paper attempt to address?

Arduino-based Embedded System for Myoelectric Hand Prostheses

Hancong Wu,Matthew Dyson,Kianoush Nazarpour

DOI: https://doi.org/10.1109/icecs49266.2020.9294843

2020-01-01

Abstract:Myoelectric hand prostheses aim to mimic the movements of the human hand. However, there is currently no cost-effective system which can flexibly switch control algorithms to achieve the user preferences and to compare these algorithms in a similar environment. To address this need, we developed a low-cost myoelectric system on the Arduino platform using module-based implementation. Two control algorithms have been implemented in this study, but extra controllers could be easily added to the system with this design. The proposed system was validated in real-time experiments with a commercial prosthesis. The control signals and control logic were analysed.
Arduino-Based Myoelectric Control: Towards Longitudinal Study of Prosthesis Use.

Hancong Wu,Matthew Dyson,Kianoush Nazarpour

DOI: https://doi.org/10.3390/s21030763

IF: 3.9

2021-01-01

Sensors

Abstract:Understanding how upper-limb prostheses are used in daily life helps to improve the design and robustness of prosthesis control algorithms and prosthetic components. However, only a very small fraction of published research includes prosthesis use in community settings. The cost, limited battery life, and poor generalisation may be the main reasons limiting the implementation of home-based applications. In this work, we introduce the design of a cost-effective Arduino-based myoelectric control system with wearable electromyogram (EMG) sensors. The design considerations focused on home studies, so the robustness, user-friendly control adjustments, and user supports were the main concerns. Three control algorithms, namely, direct control, abstract control, and linear discriminant analysis (LDA) classification, were implemented in the system. In this paper, we will share our design principles and report the robustness of the system in continuous operation in the laboratory. In addition, we will show a first real-time implementation of the abstract decoder for prosthesis control with an able-bodied participant.
A Compact Control System and A Myoelectric Control Method for Multi-DOFs Prosthetic Hand.

Bin Yang,Li Jiang,Jianhao Hu,Chongyang Li,Hong Liu

DOI: https://doi.org/10.1109/rcar47638.2019.9044103

2019-01-01

Abstract:This paper introduces a compact control system for multi-DOFs prosthetic hand. Based on the optimization of sensors configuration and hardware structure of the control system, the power consumption and volume can meet the needs of the actual using. In addition, a myoelectric control method based on the principle of finite state machine (FSM) is integrated in the control system. The proposed method enables amputees to select one of the given gestures directly, and grasp objects. As the control method requires less electromyography electrodes comparing to the traditional myoelectric control method based on EMG pattern recognition, it's available for a wider range of amputees with less active muscles. To assess the performance of the proposed method, the experiments of grasping random objects by non-amputee subjects has been conducted with the 6-DOFs HIT-V prosthetic hand, and an amputee volunteer used this prosthetic hand for one day to demonstrate viability. The non-amputee experimental results indicate that subjects can select gesture correctly among seven gestures and accomplish the designed grasping tasks with a success rate up to 96.67% within a shorter time just using two electrodes, and amputee proved viability of proposed method in daily life.
Inexpensive and Portable System for Dexterous High-Density Myoelectric Control of Multiarticulate Prostheses

Jacob A. George,Sridharan Radhakrishnan,Mark R. Brinton,Gregory A. Clark

DOI: https://doi.org/10.48550/arXiv.2001.08805

2020-01-24

Abstract:Multiarticulate bionic arms are now capable of mimicking the endogenous movements of the human hand. 3D-printing has reduced the cost of prosthetic hands themselves, but there is currently no low-cost alternative to dexterous electromyographic (EMG) control systems. To address this need, we developed an inexpensive (~$675) and portable EMG control system by integrating low-cost microcontrollers with an EMG acquisition device. We validated signal acquisition by comparing the signal-to-noise ratio (SNR) of our system with that of a high-end research-grade system. We also demonstrate the ability to use the low-cost control system for proportional and independent control of various prosthetic hands in real-time. We found that the SNR of the low-cost control system was statistically no worse than 44% of the SNR of a research-grade control system. The RMSEs of predicted hand movements (from a modified Kalman filter) were typically a few percent better than, and not more than 6% worse than, RMSEs of a research-grade system for up to six degrees of freedom when only relatively few (six) EMG electrodes were used. However, RMSEs were generally higher than RMSEs of research-grade systems that utilize considerably more (32) EMG electrodes, guiding future work towards increasing electrode count. Successful instantiation of this low-cost control system constitutes an important step towards the commercialization and wide-spread availability of dexterous bionic hands.

Robotics,Neurons and Cognition
Real-time EMG based prosthetic hand controller realizing neuromuscular constraint

Nayan M. Kakoty,Lakhyajit Gohain,Juri Borborua Saikia,Amlan Jyoti Kalita,Satyajit Borah

DOI: https://doi.org/10.1007/s41315-021-00221-z

IF: 1.7

2022-01-31

International Journal of Intelligent Robotics and Applications

Abstract:Development of prosthetic hands with human-like functionality and controllability is one of the major goals in the area of rehabilitation robotics. Current developments on prosthetic hands have earned higher functionality with multiple fingers and degrees of freedom. However, the issue of time required to perform a grasp type opens avenues for improvement in its controllability. This paper reports a real-time electromyogram (EMG) based embedded controller for prosthetic hands. The focus was on development of an efficient controller in terms of grasping accuracy and time required for grasping vis-á-vis human hand neuromuscular time constraint. The controller has been tested for a prosthetic hand to grasp four objects: cricket ball, coffee mug, screw-driver box and plastic container. EMG from biceps brachii muscles during maximum voluntary contraction versus resting state was classified. With an aim for low computational complexity in the controller such that the reported work can be translated into a low cost commercial product, a finite state algorithm was used to understand user’s grasping intention. Experiments have been accomplished in four sessions, each with 20 trials, by five subjects in both sitting and standing positions. It has been found that the prosthetic hand can perform grasping with an average accuracy of 96.2 ± 2.6%. The controller enables the prosthetic hand to perform grasping operation in 250.80 ± 1.1 ms, which is comparable to the time required by human hands i.e. 300 ms and thereby satisfied the neuromuscular constraint.
Low-Price Prosthetic Hand Controlled by EMG Signals

Narek N. Unanyan,Alexey A. Belov

DOI: https://doi.org/10.1016/j.ifacol.2021.10.463

2021-01-01

Abstract:Many people are suffering from disability, which is preventing them from doing their daily live activities. These disabilities may caused by arm amputees and congenital disorder of the musculoskeletal system. An upper limb prosthesis can help disabled people to do their usual life activity. Prosthetic devices should ideally compensate for the loss of fine, coordinated movements of the hand and have an esthetic exterior. The aim of the paper is to develop upper limb prosthetic device controlled by myoelectric signals. A prototype of prosthetic hand with novel hardware solutions and proposed software is suggested. Experimental validation of the assembled prototype is given.
Real Time Pattern Recognition for Prosthetic Hand

Mario A. Benitez Lopez,Carlos Rodriguez,Jonathan Camargo

DOI: https://doi.org/10.1115/imece2019-11788

2019-11-11

Abstract:Abstract Control of prosthetic hands is still an open problem, currently, commercial prostheses use direct myoelectric control for this purpose. However, as mechanical design advances, more dexterous prostheses with more degrees of freedom (DOF) are created, then a more precise control is required. State of the art has focused in the use of pattern recognition as a control strategy with promising results. Studies have shown similar results to classic control strategies with the advantage of being more intuitive for the user. Many works have tried to find the algorithms that best follows the user’s intention. However, deployment of these algorithms for real-time classification in a prosthesis has not been widely explored. This paper addresses this problem by deploying and testing in real-time an Artificial Neural Network (ANN). The ANN was trained to classify three different motions: no grasp, precision grasp and power grasp in order to control a two DOF trans-radial prosthetic hand with electromyographic signals acquired from two channels. Static and dynamic tests were made to evaluate the ANN under those conditions, 95% and 81% accuracy scores were reached respectively. Our work shows the potential of pattern recognition algorithms to be deployed in microcontrollers that can fit inside myoelectric prostheses.
Shared human–robot proportional control of a dexterous myoelectric prosthesis

Katie Z. Zhuang,Nicolas Sommer,Vincent Mendez,Saurav Aryan,Emanuele Formento,Edoardo D’Anna,Fiorenzo Artoni,Francesco Petrini,Giuseppe Granata,Giovanni Cannaviello,Wassim Raffoul,Aude Billard,Silvestro Micera

DOI: https://doi.org/10.1038/s42256-019-0093-5

IF: 23.8

2019-09-01

Nature Machine Intelligence

Abstract:Myoelectric prostheses allow users to recover lost functionality by controlling a robotic device with their remaining muscle activity. Such commercial devices can give users a high level of autonomy, but still do not approach the dexterity of the intact human hand. Here we present a method to control a robotic hand, shared between user intention and robotic automation. The algorithm allows user-controlled movements when high dexterity is desired, but also assisted grasping when robustness is paramount. This combination of features is currently lacking in commercial prostheses and can greatly improve prosthesis usability. First, we design and test a myoelectric proportional controller that can predict multiple joint angles simultaneously and with high accuracy. We then implement online control with both able-bodied and amputee subjects. Finally, we present a shared control scheme in which robotic automation aids in object grasping by maximizing the contact area between the hand and the object, greatly increasing grasp success and object hold times in both a virtual and a physical environment. Our results present a viable method of prosthesis control implemented in real time, for reliable articulation of multiple simultaneous degrees of freedom.

computer science, artificial intelligence, interdisciplinary applications
Investigation of Different Approaches to Real-Time Control of Prosthetic Hands With Electromyography Signals

Joao Olegario de Oliveira de Souza,Marcos Daniel Bloedow,Felipe Cezimbra Rubo,Rodrigo Marques de Figueiredo,Gustavo Pessin,Sandro Jose Rigo

DOI: https://doi.org/10.1109/jsen.2021.3099744

IF: 4.3

2021-09-15

IEEE Sensors Journal

Abstract:In this article, we describe a real-time system for prosthetic hands control. The system architecture includes the integration of the electromyographic (EMG) signal acquisition devices, platform for the implementation of the real-time classifier, sensors for the detection of object slip after grasp and the open-source hand prosthesis. Three databases were used to evaluate the implemented classifiers: a database with EMG data from local volunteers and NinaPro DB2 and DB3 databases that include electromyography and accelerometry (ACC) data acquisitions. A Multilayer Perceptron (MLP) classifier was implemented on a platform for rapid prototyping (Raspberry Pi 3 model B+) and generated responses in real-time (11 ms) with average accuracy of 96.30% for 11 hand and wrist gestures/movements.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
A robust, real-time control scheme for multifunction myoelectric control

K. Englehart,B. Hudgins

DOI: https://doi.org/10.1109/tbme.2003.813539

IF: 4.6

2003-07-01

IEEE Transactions on Biomedical Engineering

Abstract:This paper represents an ongoing investigation of dexterous and natural control of upper extremity prostheses using the myoelectric signal (MES). The scheme described within uses pattern recognition to process four channels of MES, with the task of discriminating multiple classes of limb movement. The method does not require segmentation of the MES data, allowing a continuous stream of class decisions to be delivered to a prosthetic device. It is shown in this paper that, by exploiting the processing power inherent in current computing systems, substantial gains in classifier accuracy and response time are possible. Other important characteristics for prosthetic control systems are met as well. Due to the fact that the classifier learns the muscle activation patterns for each desired class for each individual, a natural control actuation results. The continuous decision stream allows complex sequences of manipulation involving multiple joints to be performed without interruption. Finally, minimal storage capacity is required, which is an important factor in embedded control systems.

engineering, biomedical
Design of a Multi-Degree-of-freedom Virtual Hand Bench for Myoelectrical Prosthesis

Junjie Lai,Yun Zhao,Yanjian Liao,Wensheng Hou,Ying Chen,Yao Zhang,Guanglin Li,Xiaoying Wu

DOI: https://doi.org/10.1109/icarm.2017.8273186

2017-01-01

Abstract:Myoelectrical prosthesis is an important technique for restoring motor functions of amputee with strong direct sense, flexible control and convenient use. Recently, virtual reality has been introduced into the development of hand prostheses. In this paper, a multi-degree-of-freedom virtual hand bench was designed based on the mixed programming of Labwindows and Matlab. The bench utilized the editing tool of V-Realm Builder 2.0 to build the virtual hand model, and encoded driver program to control the action and its speed of the model by Simulink. Meanwhile, a mapping relationship was established between pattern recognition results and the virtual hand model. The virtual hand model could be controlled in real time with surface EMG signals. The present results showed that the virtual hand bench had good real-time performance that the completion time of each gesture was less than 175ms, and appropriate for test the sEMG processing scheme to control multi-degree freedom hand prosthesis. Furthermore, the system can be also used for training amputees to better adapt to prosthetic hands operation.
Design and Implementation of a Prosthesis System Controlled by Electromyographic Signals Means, Characterized with Artificial Neural Networks

David Tinoco-Varela,Jose Amado Ferrer-Varela,Raúl Dalí Cruz-Morales,Erick Axel Padilla-García

DOI: https://doi.org/10.3390/mi13101681

IF: 3.4

2022-10-07

Micromachines

Abstract:Around the world many people loss a body member for many reasons, where advances of technology may be useful to help these people to improve the quality of their lives. Then, designing a technologically advanced prosthesis with natural movements is worthy for scientific, commercial, and social reasons. Thus, research of manufacturing, designing, and signal processing may lead up to a low-cost affordable prosthesis. This manuscript presents a low-cost design proposal for an electromyographic electronic system, which is characterized by a neural network based process. Moreover, a hand-type prosthesis is presented and controlled by using the processed electromyographic signals for a required particular use. For this purpose, the user performs several movements by using the healthy-hand to get some electromyographic signals. After that, the obtained signals are processed in a neural network based controller. Once an usable behavior is obtained, an exact replica of controlled motions are adapted for the other hand by using the designed prosthesis. The characterization process of bioelectrical signals was performed by training twenty characteristics obtained from the original raw signal in contrast with other papers in which seven characteristics have been tested on average. The proposed model reached a 95.2% computer test accuracy and 93% accuracy in a real environment experiment. The platform was tested via online and offline, where the best response was obtained in the online execution time.

chemistry, analytical,nanoscience & nanotechnology,instruments & instrumentation,physics, applied
Biomimetic Tactile Data Driven Closed-loop Control of Myoelectric Prosthetic Hand-.

Ting Zhang,Li Jiang

DOI: https://doi.org/10.1109/robio.2018.8665126

2018-01-01

Abstract:The dexterous prosthetic hand is capable of grasping many objects with different size and shape such as precision, power, and lateral grips. However, most of these prosthetic hands haven't the ability of the tactile. Recent advances in EMG pattern recognition techniques are useful for creating hand prostheses with more intuitive control, but amputees still face the problem of lost tactile feedback. In this paper, a biomimetic tactile data driven closed-loop control of myoelectric prosthetic hand is proposed. The problem addressed in this paper is myoelectric prosthetic hand how to consistently grasp delicate objects without causing damage and dropping. The peculiarity of the proposed controller will offer the hand prostheses the ability to make rapid and accurate adjustments the grasping force based on the tactile feedback, which is similar to our very own reflex pathway. The experiments results show that the proposed controller can significantly improve the grasping function.
Design and Myoelectric Control of an Anthropomorphic Prosthetic Hand

Nianfeng Wang,Kunyi Lao,Xianmin Zhang

DOI: https://doi.org/10.1016/s1672-6529(16)60377-3

2017-01-01

Abstract:This paper presents an anthropomorphic prosthetic hand using flexure hinges, which is controlled by the surface electromyography (sEMG) signals from 2 electrodes only. The prosthetic hand has compact structure with 5 fingers and 4 Degree of Freedoms (DoFs) driven by 4 independent actuators. Helical springs are used as elastic joints and the joints of each finger are coupled by tendons. The myoelectric control system which can classify 8 prehensile hand gestures is built. Pattern recognition is employed where Mean Absolute Value (MAV), Variance (VAR), the fourth-order Autoregressive (AR) coefficient and Sample Entropy (SE) are chosen as the optimal feature set and Linear Discriminant Analysis (LDA) is utilized to reduce the dimension. A decision of hand gestures is generated by LDA classifier after the current projected feature set and the previous one are “pre-smoothed”, and then the final decision is obtained when the current decision and previous decisions are “post-smoothed” from the decisions flow. The prosthetic hand can perform prehensile postures for activities of daily living and carry objects under the control of EMG signals.
i-MYO: A Hybrid Prosthetic Hand Control System based on Eye-tracking, Augmented Reality and Myoelectric signal

Chunyuan Shi,Dapeng Yang,Jingdong Zhao,Li Jiang

DOI: https://doi.org/10.48550/arXiv.2205.08948

IF: 3.7

2022-05-18

Robotics

Abstract:Dexterous prosthetic hands have better grasp performance than traditional ones. However, patients still find it difficult to use these hands without a suitable control system. A new hybrid myoelectric control system, termed i-MYO, is presented and evaluated to solve this problem. The core component of the i-MYO is a novel grasp-type switching interface based on eye-tracking and augmented reality (AR), termed i-GSI. With the i-GSI, the user can easily switch a grasp type (six total) for a prosthetic hand by gazing at a GazeButton. The i-GSI is implemented in an AR helmet and is integrated, as an individual module, into the i-MYO system. In the i-MYO system, the myoelectric signal was used to control hand opening /closing proportionally. The operation of the i-MYO was tested on nine healthy subjects who wore HIT-V hand on the forearm and manipulated objects in a reach-and-grasp task. It was also tested on one patient who had an inferior myoelectric signal and was required to control the HIT-V hand to grasp objects. Results showed that in 91.6% of the trials, inexperienced healthy subjects accomplished the task within 5.9 s, and most failed trials were caused by a lack of experience in fine grasping. In addition, in about 1.5% of trials, the subjects also successfully transferred the objects but with a non-optimal grasp type. In 97.0% of the trials, the subjects spent ~1.3 s switching the optimal grasp types. A higher success rate in grasp type (99.1%) for the untrained patient has been observed thanks to more trials conducted. In 98.7 % of trials, the patient only needed another 2 s to control the hand to grasp the object after switching to the optimal grasp type. The tests demonstrate the control capability of the new system in multi-DOF prosthetics, and all inexperienced subjects were able to master the operation of the i-MYO quickly within a few pieces of training and apply it easily.
A low-cost robotic hand prosthesis with apparent haptic sense controlled by electroencephalographic signals

Diego Ronaldo Cutipa-Puma,Cristian Giovanni Coaguila-Quispe,Pablo Raul Yanyachi

DOI: https://doi.org/10.1016/j.ohx.2023.e00439

2023-06-02

HardwareX

Abstract:One of the biggest problems faced by amputees is obtaining a suitable low-cost prosthesis. To address this problem, the design and implementation of a transradial prosthesis controlled by electroencephalographic (EEG) signals was carried out. This prosthesis is an alternative to prostheses using electromyographic (EMG) signals, which are very complex and exhausting for the patient to execute. We collected EEG signal data using the Emotiv Insight Headset, which were then processed to control the movement of the prosthesis, known as the Zero Arm. Additionally, we incorporated Machine Learning algorithms to classify different types of objects and shapes. The prosthesis also features a haptic feedback system, which simulates the function of mechanoreceptors in the skin, providing the user with a sense of touch when using the prosthesis. Our research has yielded a viable and cost-effective prosthetic limb. We utilized 3D printing and easily obtainable servomotors and controllers, making the prosthesis affordable and accessible. Performance tests of the Zero Arm prosthesis have yielded promising results. The prosthesis demonstrated an average success rate of 86.67% across various tasks, indicating its reliability and effectiveness. Additionally, the prosthesis has an average recognition rate of 70% for different types of objects, a noteworthy accomplishment.
Development of a Low-Cost Prosthetic Hand Using Electromyography and Machine Learning

Mosab Diab,Ashraf Mohammed,Yinlai Jiang

2024-11-23

Abstract:Electromyography (EMG) is a measure of muscular electrical activity and is used in many clinical/biomedical disciplines and modern human computer interaction. Myo-electric prosthetics analyze and classify the electrical signals recorded from the residual limb. The classified output is then used to control the position of motors in a robotic hand and a movement is produced. The aim of this project is to develop a low-cost and effective myo-electric prosthetic hand that would meet the needs of amputees in developing countries. The proposed prosthetic hand should be able to accurately classify five different patterns (gestures) using EMG recordings from three muscles and control a robotic hand accordingly. The robotic hand is composed of two servo motors allowing for two degrees of freedom. After establishing an efficient signal acquisition and amplification system, EMG signals were thoroughly analyzed in the frequency and time domain. Features were extracted from both domains and a shallow neural network was trained on the two sets of data. Results yielded an average classification accuracy of 97.25% and 95.85% for the time and frequency domains respectively. Furthermore, results showed a faster computation and response for the time domain analysis; hence, it was adopted for the classification system. A wrist rotation mechanism was designed and tested to add significant functionality to the prosthetic. The mechanism is controlled by two of the five gestures, one for each direction. Which added a third degree of freedom to the overall design. Finally, a tactile sensory feedback system which uses force sensors and vibration motors was developed to enable sensation of the force inflicted on the hand for the user.

Robotics,Human-Computer Interaction
Design of an Underactuated Prosthetic Hand with Flexible Multi-Joint Fingers and EEG-Based Control

Zhicheng Teng,Guanghua Xu,Renghao Liang,Min Li,Sicong Zhang,Jiazhou Chen,Chengcheng Han

DOI: https://doi.org/10.1109/cbs.2018.8612240

2018-01-01

Abstract:Realizing more complex functions with more simple structure, lower weight/price and easier control system is still a great challenge for prosthetic hand. This paper proposed a novel underactuated prosthetic hand with flexible multi-joint finger structure based on Electroencephalogram (EEG) control. It contains 5 fingers moving independently and driven by a linear actuator each. Each finger is designed as similar integrated structure using parametric modeling method and is 3D printable, which can realize rapid fabrication and customization for different anthropometric dimensions of amputees. The adjacent phalanges are connected with flexible joints, and an elastic steel sheet is used to drive the joint to rotate. Except that the thumb contains 2 joints, each of the other four fingers contains 3 joints. We constructed a portable prototype and developed an EEG-based control system for the prosthetic hand. The pilot experiment shows it can achieve basic movements like pointing, pinching and holding, which verifies the effectiveness of this design.
Control of myoelectric prosthetic hand with a novel proximity-tactile sensor

Bin Yang,Li Jiang,ChuanYang Ge,Ming Cheng,Jia Zhang

DOI: https://doi.org/10.1007/s11431-021-2028-6

2022-06-05

Science China Technological Sciences

Abstract:Currently, prosthetic hands can only achieve several prespecified and discrete hand motion patterns from popular myoelectric control schemes using electromyography (EMG) signals. To achieve continuous and stable grasping within the discrete motion pattern, this paper proposes a control strategy using a customized, flexible capacitance-based proximity-tactile sensor. This sensor is integrated at the fingertip and measures the distance and force before and after contact with an object. During the pre-grasping phase, each fingertip's position is controlled based on the distance between the fingertip and the object to make all fingertips synchronously approach the object at the same distance. Once contact is established, the sensor turns to output the tactile information, by which the contact force of each fingertip is finely controlled. Finally, the method is introduced into the human-machine interaction control for a myoelectric prosthetic hand. The experimental results demonstrate that continuous and stable grasping could be achieved by the proposed control method within the subject's discrete EMG motion mode. The subject also obtained tactile feedback through the transcutaneous electrical nerve stimulation after contact.

materials science, multidisciplinary,engineering
Closed-Loop System for Myoelectric Hand Control Based on Electrotactile Stimulation.

Shaona Cheng,Andong Yi,U-Xuan Tan,Dingguo Zhang

DOI: https://doi.org/10.1109/icarm.2018.8610836

2018-01-01

Abstract:Prostheses are important for amputees to accomplish basic tasks in normal life. Due to lack of feedback, most prosthetic hands are easily rejected by amputees. Electrotactile feedback is a good way to close the loop of prosthetic control and improve human-computer interaction. In this work, we designed a closed-loop system for a myoelectric hand, which includes a driver module for controlling the prosthesis via electromyography (EMG), a force sensor module for measuring contact force of prosthesis, and an elcetrotactile device for delivering sensory feedback to subjects. Pilot experiments involving four amputees were carried out to test the performance on discrimination of stiffness and prosthetic grasping of bottles. Our preliminary results showed that electrotactile feedback played an important role in closed-loop control for the prosthetic hand.

Real-time Myoelectric Control with an Arduino

Arduino-based Embedded System for Myoelectric Hand Prostheses

Arduino-Based Myoelectric Control: Towards Longitudinal Study of Prosthesis Use.

A Compact Control System and A Myoelectric Control Method for Multi-DOFs Prosthetic Hand.

Inexpensive and Portable System for Dexterous High-Density Myoelectric Control of Multiarticulate Prostheses

Real-time EMG based prosthetic hand controller realizing neuromuscular constraint

Low-Price Prosthetic Hand Controlled by EMG Signals

Real Time Pattern Recognition for Prosthetic Hand

Shared human–robot proportional control of a dexterous myoelectric prosthesis

Investigation of Different Approaches to Real-Time Control of Prosthetic Hands With Electromyography Signals

A robust, real-time control scheme for multifunction myoelectric control

Design of a Multi-Degree-of-freedom Virtual Hand Bench for Myoelectrical Prosthesis

Design and Implementation of a Prosthesis System Controlled by Electromyographic Signals Means, Characterized with Artificial Neural Networks

Biomimetic Tactile Data Driven Closed-loop Control of Myoelectric Prosthetic Hand-.

Design and Myoelectric Control of an Anthropomorphic Prosthetic Hand

i-MYO: A Hybrid Prosthetic Hand Control System based on Eye-tracking, Augmented Reality and Myoelectric signal

A low-cost robotic hand prosthesis with apparent haptic sense controlled by electroencephalographic signals

Development of a Low-Cost Prosthetic Hand Using Electromyography and Machine Learning

Design of an Underactuated Prosthetic Hand with Flexible Multi-Joint Fingers and EEG-Based Control

Control of myoelectric prosthetic hand with a novel proximity-tactile sensor

Closed-Loop System for Myoelectric Hand Control Based on Electrotactile Stimulation.