Abstract:During the processing of compound feed for broilers, several changes occur that affect the physical and probably the nutritional properties of pellets, influencing animal performance. The effects of mill type, particle size (PS) and expander conditioning prior to pelleting (E+P) were combined to generate pellets. A 2 × 3 × 2 factorial arrangement was designed with two mill types (a hammer mill (HM) or roller mill (RM)), three PSs (0.8, 1.2 or 1.6 mm) and two E+Ps (with or without expander processing prior to pelleting), with six replications of 12 unsexed Ross 308 broilers each. All the processing lines reduced the PS from mash to finished pellets via secondary grinding, by 2.35 times on average. However, RM grinding required less electric power (p < 0.001). The intended PS (0.8, 1.2 or 1.6 mm) did not affect this energy consumption. E+P and the PS interacted for the pellet durability index (PDI) (p = 0.006). The worst PDI in the pellets was observed when a PS of 1.6 mm without E+P was used. Only E+P positively affected starch (p < 0.001) and amino acids' ileal apparent digestibility (p < 0.01). Organic matter (OM) (p = 0.02) and fat (p < 0.001) digestibility, as well as AMEN (p = 0.005) content, were influenced by the PS (main effect), whereas E+P and mill type interacted with these values (p < 0.005). Lower OM digestibility and AMEN content were observed when RM without E+P was used (p = 0.001). The feed conversion ratio (FCR) was enhanced and feed intake (FI) was improved with E+P. The combination of the RM mill, a 1.6 mm mean PS, and E+P improved FCR (three-way interaction, p = 0.019)), showing that for a higher PS, E+P is necessary for animal performance. Carcass yield was, on average, 80.1%. No effects on commercial cuts (breast, legs and wings) were observed. In contrast, abdominal fat was affected by mill type * PS (p = 0.012) and E+P * PS (p = 0.048) in a two-way interaction. The highest abdominal fat indicated an imbalance in the amino acid (AA)-to-AMEN ratio. Coarse PS promoted heavier gizzards (p = 0.02) but E+P tended to reduce them (p = 0.057). The processing steps improved pellet quality and feed efficiency associated with RM, coarse PS and E+P, highlighting the positive effects of E+P on abdominal fat and AMEN content, which should be adjusted to AA or reduced at formulation. However, these results are for an experimental processing plant and may not necessarily apply to larger plants, so the use of these data and methods should be considered as guidelines for replication at production sites.

Optimization of the Process Parameters for Extruded Commercial Sinking Fish Feed with Mixed Plant Protein Sources

Effect of feed moisture, extrusion temperature and screw speed on properties of soy white flakes based aquafeed: a response surface analysis

Extruded aquafeeds containing distillers dried grains with solubles: effects on extrudate properties and processing behaviour

The Experimental Study about the Influence of Extrusion System Parameters on Textured Degree of High Moisture Content Fibriform Imitated Meat

Mechanical properties of aquaculture feed pellets using plant-based proteins

Application of Food Extrusion Process to Develop Fish Meat-Based Extruded Products

Effect of extrusion process parameters on pellet crumbliness in fish feed production

Multihole Nozzle-Mediated High-Moisture Extrusion of Soy Proteins into Fiber-Rich Structures

Optimization of Twin-screw Extrusion Technology of Defatted Corn Gluten Meal by Response Surface-Methodology

Evaluation of Extruded or Unextruded Double-Low Rapeseed Meal and Multienzymes Preparation in Pigs Nutrition During the Finishing Phase of Production

Optimization of extrusion variables for the production of extruded snacks from mung bean (Vigna radiata) flour

Improvement of hybrid grouper (Epinephelus fuscoguttatus ♀ × E. lanceolatus ♂) by enzyme-digested poultry by-product: Growth performance, amino acid and peptide transport capacity, and intestinal morphology

Physical properties of defatted and extruded black soldier fly (Hermetia illucens) larvae-based aqua-feed using a twin-screw extruder

Effect of extrusion on energy and nutrient digestibility of lentil-based diets containing either supplemental plant or animal protein fed to growing pigs

Optimisation of the Extrusion Process through a Response Surface Methodology for Improvement of the Physical Properties and Nutritional Components of Whole Black-Grained Wheat Flour

Process Optimization by Response Surface Methodology and Characteristics Investigation of Corn Extrudate Fortified with Yam (Dioscorea alata L.)

Inducing Melt Elongation Flow and Controlling Cooling Temperature Facilitate the Texturization of High-Moisture Soy Protein Extrudates

Structure Design for Improving the Characteristic Attributes of Extruded Plant-Based Meat Analogues

Towards Large Particle Size in Compound Feed: Using Expander Conditioning Prior to Pelleting Improves Pellet Quality and Growth Performance of Broilers

Process Optimization of Pellet Manufacturing from Mixed Materials in Ultrasonic Vibration-Assisted Pelleting

Influence of Extruded Soybean Meal with Different Fat Contents and Varying Oleic Acid Content on Floating Fish Feed Quality and Composition