Abstract:In this study, the texture formation mechanism of a TA15 titanium alloy under different plane strain compression conditions was investigated by analyzing the slipping, dynamic recrystallization (DRX) and phase transformation behaviors. The results indicated that the basal texture component basically appears under all conditions, since the dominant basal slip makes the C-axis of the α grain rotate to the normal direction (ND, i.e., compression direction), but it has a different degree of deflection. With an increase in deformation amount, temperature or strain rate, {0001} poles first approach the ND and then deviate from it. Such deviation is mainly caused by a change in slip behaviors and phase transformation. At a smaller deformation amount and higher strain rate, inhomogeneous deformation easily causes a basal slip preferentially arising from the grain with a soft orientation, resulting in a weak basal texture component. A greater deformation amount can increase the principal strain ratio, thereby promoting other slip systems to be activated, and a lower temperature can increase the critical shear stress of the basal slip, further causing a dispersive orientation under these conditions. At a higher temperature and a lower strain rate, apparent phase transformation will induce the occurrence of lamellar α whose orientation obeys the Burgers orientation of the β phase, thereby disturbing and weakening the deformation texture. As for DRX, continuous-type (CDRX) is most common under most conditions, whereas CDRX grains have a similar orientation to deformed grains, so DRX has little effect on overall texture. Moreover, the microhardness of samples is basically inversely proportional to the grain size, and it can be significantly improved as lamellar α occurs. In addition, deformed samples with a weaker texture present a higher microhardness due to the smaller Schmidt factors of the activated prism slip at ambient loading.

Orientation Dependent Behavior of Tensile-Creep Deformation of Hot Rolled Ti65 Titanium Alloy Sheet

Effect of texture on the room temperature tensile and creep properties of Ti–6Al–4V plate with large thickness

Creep Anisotropy Characteristics and Microstructural Crystallography of Marine Engineering Titanium Alloy Ti6321 Plate at Room Temperature

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Microstructure and Texture Variations in High Temperature Titanium Alloy Ti65 Sheets with Different Rolling Modes and Heat Treatments

The Action Mechanism of Rolling Texture on the Anisotropic Behavior of a Pure Titanium Plate

Microstructure Evolution and Mechanical Properties of Pure Ti Alloy Sheet Fabricated by Double-Side Corrugated Rolling

Mechanism of Crystallographic Orientation and Texture Evolution of Ti60 Alloy during Plane Strain Compression

Transverse texture weakening and anisotropy improvement of Ti-6Al-4V alloy sheet via asymmetric rolling and static recrystallization annealing

Constitutive Model and Microstructure Evolution of a Novel TG6 High-Temperature Titanium Alloy during Hot Deformation

Effect of Solution Treatment on Microstructure, Texture, and Anisotropy of Mechanical Properties in TA10 (Ti-0.3Mo-0.8Ni) Sheet

Effect of Deformation Temperature on the Microstructure and Texture Evolution of Ti-6Al-4Zr-2Mo-6V Alloy

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Influence of Initial Textures on Microstructure and Mechanical Properties of Commercially Pure TA2 Titanium Sheet Pre-Strained by Cryorolling

Suppression of texture and enhancement of high-temperature tensile property in heavily deformed gradient Ti 2 AlNb alloy

The Role of Deformation and Microstructure Evolution on Texture Formation of a TA15 Alloy Subjected to Plane Strain Compression

Microstructural evolution and FCC twinning behavior during hot deformation of high temperature titanium alloy Ti65

Static Recrystallization Behavior and Texture Evolution during Annealing in a Cold Rolling Beta Titanium Alloy Sheet

High-temperature tensile deformation behavior and microstructure evolution of Ti55 titanium alloy

Superplastic Deformation Behavior of 2 mm Ti60 Rolled Sheet in Air Environment

Effects of rolling deformation on microstructure orientations and tensile properties of TiB/(TA15-Si) composites