A Facile Surface Modification of a PVDF Membrane Via CaCO3 Mineralization for Efficient Oil/water Emulsion Separation

Junda Wu,Atian Xie,Jin Yang,Jiangdong Dai,Chunxiang Li,Yongsheng Yan,Jiuyun Cui

DOI: https://doi.org/10.1039/d0nj03329d

IF: 3.3

2020-01-01

New Journal of Chemistry

Abstract:A facile modification of a PVDF membrane using CaCO3 inorganic particles via a layer-by-layer self-assembly process for efficient oil/water separation.

What problem does this paper attempt to address?

Polydopamine-CaCO3 Modified Superhydrophilic Nanocomposite Membrane Used for Highly Efficient Separation of Oil-in-water Emulsions

Feng Shijie,Zhao Jiefeng,Gao Yunling,Yun Junxian

DOI: https://doi.org/10.1016/j.colsurfa.2022.128355

IF: 5.518

2022-01-01

Colloids and Surfaces A Physicochemical and Engineering Aspects

Abstract:A superhydrophilic/underwater superoleophobic CaCO3@PDA@nylon nanocomposite membrane was prepared by a simple dip-coating method using a nylon 66 membrane in dopamine and nano CaCO3 particle aqueous solutions. The prepared CaCO3@PDA@nylon membrane was characterized by SEM, EDS, FTIR, and XPS. The underwater oil contact angle reached 159.7 degrees. The modified membrane showed highly efficient oil-in-water emulsion separation performance for various viscous oils or organic solvents over a wide range from 126.8 to 6029.6 nm. Furthermore, the CaCO3@PDA@nylon membrane also demonstrated high permeation flux and good regeneration ability. Even with continuous reuse of 15 cycles, the flux was still high, e.g., 517.3 L m- 2 h-1 for chloroform-in-water emulsions with an average particle size of 126.8 nm. The modified membrane's possible oilin-water emulsion separation mechanism was obtained by combining fluorescence-assisted dripping, continuous filtration, and emulsion contact angle experiments. This work might provide a simple and environmentally friendly membrane modification method for general separation studies of high oil concentration oil-in-water emulsions. The simple preparation process and efficient and fast separation ability highlight its great potential in large-scale production and oily wastewater treatment.
A Degradable Super-Hydrophilic/Underwater Super-Oleophobic Membrane Prepared by a Green Modification Method for Efficient Oil-in-Water Emulsion Separation

Feng Shijie,Zhao Jiefeng,Zhang Pengyu,Yunling Gao,Yun Junxian

DOI: https://doi.org/10.2139/ssrn.3978462

2021-01-01

SSRN Electronic Journal

Abstract:Environmentally friendly separation materials are essential for the separation of emulsified oil-water mixtures. The nylon membrane has been facilely converted into highly hydrophilic and underwater super-oleophobic via a simple one-step co-deposition of polydopamine and CS-TPP nanoparticles, wherein the CS-TPP particles were prepared by the ion gel method. The modified membrane exhibits excellent antifouling performance with UOCAâ‰ˆ179.6. The prepared environmental CS-TPP@PDA@nylon membrane was characterized by SEM, EDS, FTIR, and XPS. The membrane can separate various oil-in-water emulsions in a wide range of average particle sizes (50.9-1832.0 nm). In addition, the CS-TPP@PDA@nylon membrane demonstrated high permeation flux (221.0-1770.5 L m-2 h-1) and good regeneration ability. Even after fifteen cycles, the flux can still maintain more than 89%. The green and non-toxic modifier and simple preparation process highlight the modified membrane's massive potential in large-scale production and green oily wastewater treatment.
Superhydrophilic/underwater Superoleophobic Oil-in-water Emulsion Separation Membrane Modified by the Co-Deposition of Polydopamine and Chitosan-Tripolyphosphate Nanoparticles

Feng Shijie,Zhao Jiefeng,Zhang Pengyu,Gao Yunling,Yun Junxian

DOI: https://doi.org/10.1016/j.jece.2022.107407

IF: 7.7

2022-01-01

Journal of Environmental Chemical Engineering

Abstract:Environmentally friendly separation materials are essential for separating emulsified oil-water mixtures. The nylon membrane has been facilely converted into highly hydrophilic and underwater superoleophobic via a simple one-step co-deposition of polydopamine and chitosan-tripolyphosphate (CS-TPP) nanoparticles, wherein the CS-TPP particles were prepared by the ion gel method. The modified membrane exhibited excellent antifouling performance with the underwater oil contact Angle (UOCA) at 179.6 degrees. The prepared environmental CS-TPP@PDA@nylon membrane was characterized by SEM, EDS, FTIR, and XPS. The membrane could separate various oil-in-water emulsions in a wide range of average particle sizes (50.9-1832.0 nm). In addition, the CS-TPP@PDA@nylon membrane demonstrated high permeation flux (221.0-1770.5 L m(-2) h(-1)) and good regeneration ability. The flux could still maintain more than 89% even after fifteen cycles. The degradable modification materials and simple preparation process would highlight the potential of modified membranes in large-scale production and green oily wastewater treatment.
Janus membrane with asymmetric wettability for efficient oil/ water separation

Boyang Tian,Baona Ren,Miaomiao Hu,Yiwen Yang,Jing Wu

DOI: https://doi.org/10.1016/j.heliyon.2023.e22534

IF: 3.776

2023-01-01

Heliyon

Abstract:The rapid development of society and industry as well as the frequent occurrence of oil spills cause the shortage of fresh water resources, which not only affects human safety and life, but also impedes the world-wide sustainable development. To address these challenges, novel membrane materials with unique wettability properties have gained significant attention, particularly in the field of oil/water separation. In this research, we modified the hydrophobic PET fabric to achieve superhydrophilic characteristics using impregnation method. Subsequently, we electrospun hydrophobic PVDF fibers onto the superhydrophilic fabric surface, and PVDF/Ca10(PO4)6(OH)2@-PET Janus membrane with asymmetric wettability was obtained. The membrane has an excellent unidirectional liquid transport capacity, and can effectively separate heavy oil or light oil, the separation efficiency is more than 90 %. The results also show that the Janus membrane can be used under alkaline conditions and has satisfactory tensile resistance and re-use performance. This work provides a new idea for Janus membrane design and effectively improves the application potential of the Janus membrane in the field of oil/water separation.
Fabrication of Ph-Sensitive Superhydrophilic/Underwater Superoleophobic Poly(vinylidene Fluoride)-Graft-(sio2 Nanoparticles and PAMAM Dendrimers) Membranes for Oil-Water Separation.

Chenjie Wei,Ligang Lin,Yiping Zhao,Xiaoye Zhang,Ning Yang,Li Chen,Xiaojun Huang

DOI: https://doi.org/10.1021/acsami.9b22881

IF: 9.5

2020-01-01

ACS Applied Materials & Interfaces

Abstract:The efficient treatment of oil-water emulsions under acidic condition remains a widespread concern. Poly(amidoamine) (PAMAM) dendrimer with hyperbranched structures and a large amount of primary and tertiary amino groups has exhibited advantages to solve this issue. Here, a novel poly(vinylidene fluoride)-graft-(SiO2 nanoparticles and PAMAM dendrimers) (PVDF-g-SiO2 NPs/PAMAM) membrane was fabricated using a surface-grafting strategy. SiO2 NPs were immobilized on PVDF-g-poly(acrylic acid) (PAA) membranes for improving the surface roughness, and PAMAM dendrimers were further immobilized on the membrane surface by interfacial polymerization (IP) for improving the surface energy. The obtained membrane demonstrated a water contact angle and a stable underwater-oil contact angle of 0 degrees and >150 degrees, respectively. These characteristics endowed the membrane with excellent water permeability [>3100 L/(m(2).h) at 0.9 bar] and separation efficiency (>99%) during oil-water separation. Furthermore, the PAMAM chain will extend from a collapsed state into a fully extension state because of the protonation of amine groups under acidic condition, thus achieving a low underwater oil-adhesion property, fouling resistance, desirable stability, and recyclability (over 12 cycles) during usage. This work shows a promising prospect for the treatment of corrosive emulsions under acidic condition.
Biomimetic hydrophilic modification of poly (vinylidene fluoride) membrane for efficient oil-in-water emulsions separation

Shaobo Zhang,Yi Li,Yan Yuan,Li Jiang,Haitao Wu,Yanmao Dong

DOI: https://doi.org/10.1016/j.seppur.2023.125227

IF: 8.6

2023-10-03

Separation and Purification Technology

Abstract:Membrane separation is one of the simple and efficient methods for treating oily wastewater. To improve the efficiency of oil-in-water emulsion separation, alkali treatment was used to promote the deposition of Fe (III) on poly (vinylidene fluoride) (PVDF) membranes, and the tannic acid (TA)-glutathione (GSH) hydrophilic coating was produced on the membrane surface by biomimetic coating method under weak alkaline conditions. The PVDF membrane with hydrophilic coating and multi-layered surface structure showed hydrophilic/ underwater superoleophobic. Meanwhile, the permeability and antifouling properties were significantly enhanced. According to the experimental results, the optimized modified membrane (MF-3) had excellent pure water flux (3368.0 ± 94.2 L·m −2 ·h −1 ), and oil rejection was 99.3 ± 0.2 % for toluene-in-water emulsion. In addition, after simulated fouling and regeneration by bovine serum albumin (BSA) solution, the flux recovery rate reached 97.0 %. Excellent underwater anti-oil adhesion and antifouling properties help maintain high separation efficiency during multiple filtration cycles. The chemical stability of the modified membranes was demonstrated after 7 d immersion in acid, alkali, and salt solutions, respectively. The superior performances of the membrane are attributed to the constructed hydrophilic coating. This environmentally friendly PVDF membrane modification strategy has great potential for application in oil-in-water emulsion separation and provides a reliable solution for sustainable development.

engineering, chemical
A facile approach to silica-modified polysulfone microfiltration membranes for oil-in-water emulsion separation

Qiao-ling Gao,Fei Fang,Chen Chen,Xue-Yan Zhu,Jing Li,Hong-Ying Tang,Zhong-Biao Zhang,Xiao-Jun Huang

DOI: https://doi.org/10.1039/c6ra07929f

IF: 4.036

2016-01-01

RSC Advances

Abstract:A versatile strategy to fabricate newly-developed silica-modified membranes based on organic/inorganic hybridization for oil/water separation is described in this study. The modified membranes are easily obtained by a simple two-step immersion of polysulfone hollow fiber membranes with radial gradient microstructure (RGM-PSF) into a silicon solution of tetraethyl orthosilicate (TEOS) mixed with 3glycidyloxypropyltrimethoxysilane (COPTS) and subsequently into a lactic acid solution. Attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and field emission scanning electron microscopy (FE-SEM) were utilized to characterize the surface compositions and microstructures. A micro/nano-scaled SiO2-based coating was generated roughly and continuously on the membrane surfaces, endowing them with superhydrophilicity and underwater superoleophobicity. Results of dead-end filtration experiments demonstrated that the hybridized RGMPSF membranes could be applied in oil-in-water emulsion separation far more efficiently, with higher water permeate flux, better oil rejection ratio, and higher pressure endurance than those of the common ones. Therefore, this study has provided a facile approach to prepare silica -modified membranes with special wettability, showing prominent application prospects for oily wastewater treatment in practical processes.
Rapid Construction of Caffeic Acid/ p -Phenylenediamine Antifouling Hydrophilic Coating on a PVDF Membrane for Emulsion Separation

Yujia Tong,Changing Miao,Wenlong Ding,Fiona Hammond Quarcoo,Xiao Xiao,Hongjun Ji,Weixing Li,Xiaohui Ju

DOI: https://doi.org/10.1021/acs.langmuir.3c01627

IF: 3.9

2023-09-07

Langmuir

Abstract:The current methods of constructing modification strategies for hydrophilic membranes are time-consuming, complex in operation, and poor in universality, which limit their application on membranes. In this work, inspired by the adhesion properties and versatility of caffeic acid (CA) and p-phenylenediamine (PPDA), a simple, rapid, and universal method was designed for the separation of oil-in-water emulsion by preparing a stable hydrophilic coating separation membrane. The preparation time of the membrane was shortened to 40 min. The developed PVDF-PCA/PPDA membrane showed superhydrophilic and underwater superoleophobic properties. When applied to petroleum ether-in-water emulsion, isooctane-in-water emulsion, and dodecane-in-water emulsion separation, the oil rejection was more than 99.0%. In the circulating separation of 10 g/L soybean oil-in-water emulsion, the oil rejection was more than 99.3%, and the highest flux was 1036 L·m-2·h-1. The prepared PVDF-PCA/PPDA membrane performed well in the separation test of oily wastewater. The proposed strategy is simple and rapid; it may become a universal method for preparing membranes with super strong antifouling properties against viscous oil and accelerate the research progress of membrane separation of oil-in-water emulsions.

chemistry, multidisciplinary, physical,materials science
Polyvinylidene Fluoride-Based Ultrafiltration Composite Membranes Via In-Situ Biomineralization

Suo-Hong Zhi,Bo Zhang,Le-Yuan Han,Wei-Qiang Xiao,Jie Ying,Guo-Hai Chu,Guo-Jun Zhou,Ling-Shu Wan,Zhi-Kang Xu

DOI: https://doi.org/10.1142/9789813220393_0004

2017-01-01

Abstract:This paper develops a polyvinylidene fluoride (PVDF) / polyacrylic acid (PAA)/calcium carbonate (CaCO3) composite membrane using the in-situ mineralization method. PAA is used as polyanionic macromolecule to induce the generation of CaCO3 particles. The mineralization condition was optimized based on CaCl2 content in the selection process of the casting solution and carbonate source. The structures and surface hydrophilicity were characterized by field emission scanning electron microscope (FESEM), Fourier transform infrared/attenuated total reflection (FT-IR/ATR) spectrometer, energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD) and water contact angle for the prepared composite membranes. The results demonstrate that CaCO3 particles consisting of calcite and vaterite disperse uniformly on the membrane surface and in the membrane cross-section; the membrane hydrophilicity increases with the increase of CaCl2 content in the casting solution. The improved hydrophilicity is resultant of the membrane structure in the in-situ mineralization process and the collapse of PAA chains in the membrane pores, facilitating the tenfold improvement of the membrane's pure water fluxes. Due to the electrostatic repulsion between the positively charges lysozyme and CaCO3 particles, the mineralized membranes possess a high rejection (85.13%) and flux recovery ratio (77.21%). Therefore, in-situ mineralization is a convenient and effective method to prepare hydrophilic composite PVDF membranes.
Bio-inspired Fabrication of Superhydrophilic Nanocomposite Membrane Based on Surface Modification of SiO2 Anchored by Polydopamine Towards Effective Oil-Water Emulsions Separation

Jiuyun Cui,Zhiping Zhou,Atian Xie,Minjia Meng,Yanhua Cui,Siwei Liu,Jian Lu,Shi Zhou,Yongsheng Yan,Hongjun Dong

DOI: https://doi.org/10.1016/j.seppur.2018.03.054

IF: 8.6

2019-01-01

Separation and Purification Technology

Abstract:A new PVDF@pDA@SiO2 nanocomposite membrane was fabricated by virtue of the surface modification of polydopamine anchored SiO2 on PVDF membrane through a facile and eco-friendly preparation process. It possessed the superior superhydrophilicity/underwater superoleophobicity properties and presented the out standing antifouling oil performance and high-efficiency separation ability for oil-water emulsions, which mainly resulted from its special surface micro-nano structure and pore induced capillarity phenomenon. Furthermore, the PVDF@pDA@SiO2 nanocomposite membrane also exhibited the splendid separation performance, regeneration ability and universality for various oil-water emulsions separation. In addition, the oil water emulsion separation mechanism was discussed in depth. This work might provide a significant guidance for large-scale production and application of this nanocomposite membrane in the fields of wastewater recovery and drinking water treatment.
Facile preparation of metal-polyphenol coordination complex coated PVDF membrane for oil/water emulsion separation

Junda Wu,Zhiqiang Hou,Zhixin Yu,Jihui Lang,Jiuyun Cui,Jin Yang,Jiangdong Dai,Chunxiang Li,Yongsheng Yan,Atian Xie

DOI: https://doi.org/10.1016/j.seppur.2020.118022

IF: 8.6

2021-03-01

Separation and Purification Technology

Abstract:Owing to the complex application environments, designing and fabricating emulsion separation membrane via facile preparation method with high separation efficiency and superior chemical stability are necessary. Herein, the composite membranes via facile layer-by-layer self-assembly process with the merits of low-cost and eco-friendly have been reported. The property of composite membrane can be regulated via changing the times of coating process, shows great experimental flexibility and practicability. Additionally, the separation efficiency of prepared membrane is as high as 99.35%, and the permeation flux is 689.6 L m-2h−1 bar−1. Most importantly, the prepared composite membrane exhibits superior chemical stability (acid/alkali/salt resistance) and outstanding underwater oil repellence property. The separation efficiency of the composite membrane which treated by acid/alkali solutions are all above 97.39%. Generally, the low-cost and eco-friendly composite membrane via facile coating process is appropriate for oily water treatment in the practical complicated environment, and possesses great potential in oil/water emulsion separation.

engineering, chemical
Poly(vinylidene Fluoride)/poly(acrylic Acid)/calcium Carbonate Composite Membranes Via Mineralization

Suo-Hong Zhi,Ling-Shu Wan,Zhi-Kang Xu

DOI: https://doi.org/10.1016/j.memsci.2013.12.011

IF: 9.5

2014-01-01

Journal of Membrane Science

Abstract:Organic–inorganic composite membranes were prepared via calcium carbonate (CaCO3) mineralization induced by poly(vinylidene fluoride) (PVDF)/poly(acrylic acid) (PAA) blend membranes. PAA was used as a polyanionic macromolecule in the blend membranes to generate CaCO3 particles by an alternate soaking process (ASP). The mineralization condition was optimized based on the concentrations of calcium chloride (CaCl2) and sodium carbonate (Na2CO3) solutions used for ASP, the number of ASP cycles, and the PAA content in the blend membranes. Structures and surface hydrophilicity of the composite membranes were characterized in detail by FTIR-ATR, FESEM, EDX, XRD and water contact angle. Results confirm that CaCO3 particles consisting of calcite and vaterite dispersed uniformly in/on the membranes. The membrane hydrophilicity increased dramatically due to the intrinsic wettability of these CaCO3 particles. In addition, the CaCO3 particles also caused the collapse of PAA chains in the membrane pores. Therefore, pure water fluxes of the membranes were improved about three times. Furthermore, the mineralized membranes even showed a high rejection (99.85%) of Congo red, which makes them potential in dye-polluted wastewater treatment.
Inner Surface Hydrophilic Modification of PVDF Membrane with Tea Polyphenols/Silica Composite Coating

Qiang Xu,Xiaoli Ji,Jiaying Tian,Xiaogang Jin,Lili Wu

DOI: https://doi.org/10.3390/polym13234186

IF: 5

2021-11-30

Polymers

Abstract:The use of Polyvinylidene fluoride (PVDF) membranes is constrained in wastewater treatment because of their hydrophobic nature. Therefore, a large number of researchers have been working on the hydrophilic modification of their surfaces. In this work, a superhydrophilic tea polyphenols/silica composite coating was developed by a one-step process. The composite coating can achieve not only superhydrophilic modification of the surface, but also the inner surface of the porous PVDF membrane, which endows the modified membrane with excellent water permeability. The modified membrane possesses ultrahigh water flux (15,353 L·m−2·h−1). Besides this, the modified membrane can realize a highly efficient separation of oil/water emulsions (above 96%).

polymer science
A Facile Method to Control Pore Structure of PVDF/SiO2 Composite Membranes for Efficient Oil/Water Purification

Qianqian Xu,Yuchao Chen,Tonghu Xiao,Xing Yang

DOI: https://doi.org/10.3390/membranes11110803

IF: 4.562

2021-10-22

Membranes

Abstract:The use of poly(vinylidene fluoride) (PVDF) microfiltration (MF) membranes to purify oily water has received much attention. However, it is challenging to obtain high-performance PVDF microfiltration membranes due to severe surface fouling and rapid decline of permeability. This study explored a new approach to fabricate high-performance PVDF/silica (SiO2) composite membrane via the use of a polymer solution featuring lower critical solution temperature (LCST) characteristics and the non-solvent thermally induced phase separation method (NTIPS). Coupling with morphological observations, the membrane formation kinetics were analyzed in depth to understand the synergistic effect between the LCST solution properties and fabrication conditions in NTIPS. Utilizing such a synergistic effect, the transition from finger-like macrovoid pores to bi-continuous highly connected pores could be flexibly tuned by increasing the PVDF concentration and the weight ratio of SiO2/PVDF in the dope solution and by raising the coagulation temperature to above the LCST of the solution. The filtration experiments with surfactant-stabilized oil-water emulsion showed that the permeation flux of the PVDF/SiO2 composite membranes was higher than 318 L·m−2·h−1·bar−1 and the rejection above 99.2%. It was also shown that the PVDF/SiO2 composite membranes, especially those fabricated above the LCST, demonstrated better hydrophilicity, which resulted in significant enhancement in the anti-fouling properties for oil/water emulsion separation. Compared to the benchmark pure PVDF membrane in oily water purification, the optimal composite membrane T70 was demonstrated via the 3-cycle filtration experiments with a significantly improved flux recovery ratio (Frr) and minimal reduced irreversible fouling (Rir). Overall, with the developed method in this work, facile procedure to tune the membrane morphology and pore structure was demonstrated, resulting in high performance composite membranes suitable for oil/water emulsion separation.

engineering, chemical,materials science, multidisciplinary,polymer science,chemistry, physical
Fabrication of Modified PVDF Membranes with PAA Network Polymer for Highly Efficient Oil/water Emulsion Separation

Chen Zhao,ShanShan Wang,Nianping Wang

DOI: https://doi.org/10.1016/j.seppur.2024.130138

IF: 8.6

2025-01-01

Separation and Purification Technology

Abstract:Dip coating technology is often used for hydrophilic modification of PVDF membrane surfaces due to its significant modification effect, simple process and low cost. Nevertheless, the relatively feeble binding forces between coating molecules and between the coating and the substrate membrane often raise concerns about the stability of modified membranes. This study utilized PAA and Sac-100 to develop a hydrophilic and negatively charged coating to improve the anti-fouling characteristics of PVDF membranes in the process of oil/water separation. Two modification reagents underwent ring opening crosslinking reaction and ultimately deposited on the surface of PVDF membranes in the form of a network polymer, thereby solving the stability problem of the modification coating. After the modification, the surface microstructure of the membranes remained unchanged, while the average pore size fell from 0.37 mu m to 0.32 mu m. The water contact angle of the modified membrane decreased to 39 degrees suggesting an excellent hydrophilic property. The modified PVDF membrane exhibited exceptional resistance to fouling in the oil/water separation experiment, demonstrating a consistent permeance value of 212 L m- 2 h- 1 bar- 1 that was four times higher than that of the original membrane. Following the cleaning process, the permeance of the modified membrane could be restored to a level of 74.5 %.
Construction of robust DA@CNTs/CS hydrogel coatings on hydrophobic PVDF membrane by deposition of self-assembly for efficient separation of oil-water emulsion and dye wastewater

Jingxuan Zhao,Hongxu Liu,Yuchao Qi,Ruijia Wang,Ziwei Lv,Yang Yu,Shulin Sun

DOI: https://doi.org/10.1016/j.seppur.2023.125956

IF: 8.6

2023-12-10

Separation and Purification Technology

Abstract:With the rapid development of industry, the problem of water pollution has become increasingly serious. Though there are many separation materials available to solve this problem, how to separate multiple wastewater at the same time remains a challenge. Hydrogel coating is suitable for use in the field of oil–water separation, and chitosan (CS) is effective in removing anionic dyes. Therefore, the preparation of separation membranes with hydrogel coating containing CS and dopamine (DA) can effectively separate oil–water emulsion and anionic dye wastewater. In this paper, DA@CNTs/CS hydrogel coating was prepared by sequentially coating Cu 2+ , DA@CNTs, Cu 2+ and CS on the surface of polyvinylidene fluoride (PVDF) membrane by deposition of self-assembly, which enhanced the hydrophilicity of the membrane and made it highly underwater oleophobic and antifouling. The alkali treated PVDF membrane contained a large amount of –OH, Cu 2+ , which formed coordination bonds with –OH, CS, and DA and the hydrogel coating could be stably loaded on the membrane. In addition, the introduction of rigid CNTs effectively improved the performance of the modified membrane under extreme conditions such as high pH and high salt concentration. PVDF-DA@CNTs/CS membrane had an ideal pure water flux (PWF) of 1470 (L·m −2 ·h −1 ) and the separation efficiency of 99.7 % for anionic dye and 99.4 % for oil–water emulsion. The contaminant on the membrane surface can be quickly removed by washing with DI water. The overall performance of the membrane is also maintained at a very high level of long-term filtration of wastewater. In summary, this study provides a new approach to complex wastewater treatment technology.

engineering, chemical
One-pot fabrication of SF-DA@PVDF membrane for dye adsorption and oil-in-water emulsion separation

Peng Zhou,Shihong Zhang,Yi He,Jingcheng Wu,Liang Zhou,Xiangying Yin,Shuting Tian,Shuangshuang Li,Wen Chen

DOI: https://doi.org/10.1016/j.jece.2023.109730

IF: 7.7

2023-04-01

Journal of Environmental Chemical Engineering

Abstract:With industry development, the reuse of water and oil resources has become an urgent problem. At present, the evolution of simple-minded approaches to attain modification on the membrane surface for a more complex circumstance, such as oily wastewater and dyes at the same time, has become a red-hot but challenging topic for research. Membrane separation technology has successfully built up to cope with these issues, such as oil-in-water emulsion separation and dye adsorption owning to its benign mechanical characteristics and low power consumption. Therefore, we report a simple-minded one-step approach for uses in oil-in-water emulsion separation and dye adsorption. In this work, a new multifunctional membrane surface is constructed via the concurrent incorporation of silk fibroin (SF) and dopamine hydrochloride (DA) in co-deposition to reach a large flux for complex wastewater separation. The qualified membrane has super hydrophilic in the air and has brilliant oil adhesion resistance underwater. It works comfortably on oil-in-water emulsions (over 10400 L m −2 h −1 bar −1 ) or dyes (above 3738.68 mg m −2 ). More importantly, excellent adsorption efficiency (>99%) and extensive adsorption capability (over 2071.91 mg m −2 ) were achieved by the oil-in-dye emulsion that stabilized with surfactant. It not only possesses a broad span of use outlooks but also enlightens imports for the evolution of functional coating in the future.

engineering, chemical, environmental
Fabrication of a superhydrophilic PVDF membrane with excellent chemical and mechanical stability for highly efficient emulsion separation

Ming Wang,Zewen Xu,Yingfei Hou,Peng Li,Haixiang Sun,Q. Jason Niu

DOI: https://doi.org/10.1016/j.seppur.2020.117408

IF: 8.6

2020-11-01

Separation and Purification Technology

Abstract:The separation and recovery of oil from oily wastewater was still challenging due to the limitations of conventional separation techniques in its limited application fields, high operation cost and low separation efficiency. Membrane separation was a novel candidate to satisfy various separation tasks. Seeking for an efficient and facile strategy to manipulate the membrane performance was urgently needed. Chinese ink was a promising material to functionalize the membrane by virtue of the self-adhesion and intrinsic hydrophilicity. Herein, a composite polyvinylidene fluoride (PVDF) microfiltration membrane was fabricated via a facile rub-coating strategy. The micro/nano structures derived from the nanoparticles in Chinese ink readily facilitated the membrane with the superhydrophilicity and underwater superoleophobicity (underwater various oils contact angle above 150°, underwater dichloromethane roll off angle ~ 3°). The composite membrane exhibited a high permeation flux, a considerable separation efficiency for separating various oil-in-water emulsions and a superior recyclability for separating gasoline-in-water emulsion in ten cycles. Moreover, the membrane maintained a desirable underwater dichloromethane contact angle (above 145°) after respectively being immersed in pH = 1 HCl, pH = 13 NaOH and 3.5 wt% NaCl solutions for one week, and a sandpaper abrasion test, demonstrating an excellent chemical stability and a robust mechanical durability.

engineering, chemical
One-Step Phase Separation and Mineralization Fabrication of Membranes for Oily Wastewater Treatment

Mengyang Hu,Yu-Hsuan Chiao,Wenming Fu,Pengfei Zhang,Shang Fang,Kecheng Guan,Ralph Rolly Gonzales,Zhan Li,Ping Xu,Zhaohuan Mai,Liheng Dai,Hideto Matsuyama

DOI: https://doi.org/10.1021/acsami.4c07067

IF: 9.5

2024-07-13

ACS Applied Materials & Interfaces

Abstract:Oily wastewater threatens the environment and the human health. Membrane technology offers a simple and efficient alternative to separating oil and water. However, complex membrane modifications are usually employed to optimize the separation performance. In this research, we develop an extremely simple one-step method to in situ calcium carbonate (CaCO(3)) nanoparticles onto a porous polyketone (PK) membrane via a nonsolvent induced phase separation (NIPS)-mineralization strategy. We utilized...

materials science, multidisciplinary,nanoscience & nanotechnology
Fast fabricating superhydrophilic PVDF membrane via proanthocyanidins crosslinking at room temperature

Changqing Miao,Yujia Tong,Fiona Hammond Quarcoo,Xiaohui Ju,Weixing Li

DOI: https://doi.org/10.1016/j.seppur.2024.127346

IF: 8.6

2024-04-13

Separation and Purification Technology

Abstract:Mussels in nature can adhere to the surface of hydrophobic substances by secreting adhesive substances, which has attracted wide attention by coating method for membrane modification. However, complicated processing procedures remain major problems. Here, we proposed a simple, mild and fast surface coating method. Proanthocyanidins (PC) react with 3-aminopropyl triethoxysilane (KH550) under the accelerated action of the oxidant ammonium persulfate (APS) at room temperature to form a polyphenol network. The hydrophilic network coating was constructed on PVDF membrane by surface co-deposition method for 1 h, which could effectively separate different emulsions. The water permeability of modified membrane was 18,271 L∙m −2 ∙h −1 ∙bar −1 . The permeability for separating isooctane-in-water emulsion arrived at 14,223 L∙m −2 ∙h −1 ∙bar −1 and the oil rejection rate was 99.6 %. After ten cycles, the separation flux was 10,836 L∙m −2 ∙h −1 ∙bar −1 with the rejection rate of 98.8 %. Modified membranes were soaked in acid and alkali salt solutions of different pH values for 30 days, and maintained good underwater oleophobic performance (>156°). The developed membrane showed excellent separation performance, oleophobic property and acid-base stability. The proposed membrane modification strategy was prospective for efficient separation of oily wastewater.

engineering, chemical

A Facile Surface Modification of a PVDF Membrane Via CaCO3 Mineralization for Efficient Oil/water Emulsion Separation

Polydopamine-CaCO3 Modified Superhydrophilic Nanocomposite Membrane Used for Highly Efficient Separation of Oil-in-water Emulsions

A Degradable Super-Hydrophilic/Underwater Super-Oleophobic Membrane Prepared by a Green Modification Method for Efficient Oil-in-Water Emulsion Separation

Superhydrophilic/underwater Superoleophobic Oil-in-water Emulsion Separation Membrane Modified by the Co-Deposition of Polydopamine and Chitosan-Tripolyphosphate Nanoparticles

Janus membrane with asymmetric wettability for efficient oil/ water separation

Fabrication of Ph-Sensitive Superhydrophilic/Underwater Superoleophobic Poly(vinylidene Fluoride)-Graft-(sio2 Nanoparticles and PAMAM Dendrimers) Membranes for Oil-Water Separation.

Biomimetic hydrophilic modification of poly (vinylidene fluoride) membrane for efficient oil-in-water emulsions separation

A facile approach to silica-modified polysulfone microfiltration membranes for oil-in-water emulsion separation

Rapid Construction of Caffeic Acid/ p -Phenylenediamine Antifouling Hydrophilic Coating on a PVDF Membrane for Emulsion Separation

Polyvinylidene Fluoride-Based Ultrafiltration Composite Membranes Via In-Situ Biomineralization

Bio-inspired Fabrication of Superhydrophilic Nanocomposite Membrane Based on Surface Modification of SiO2 Anchored by Polydopamine Towards Effective Oil-Water Emulsions Separation

Facile preparation of metal-polyphenol coordination complex coated PVDF membrane for oil/water emulsion separation

Poly(vinylidene Fluoride)/poly(acrylic Acid)/calcium Carbonate Composite Membranes Via Mineralization

Inner Surface Hydrophilic Modification of PVDF Membrane with Tea Polyphenols/Silica Composite Coating

A Facile Method to Control Pore Structure of PVDF/SiO2 Composite Membranes for Efficient Oil/Water Purification

Fabrication of Modified PVDF Membranes with PAA Network Polymer for Highly Efficient Oil/water Emulsion Separation

Construction of robust DA@CNTs/CS hydrogel coatings on hydrophobic PVDF membrane by deposition of self-assembly for efficient separation of oil-water emulsion and dye wastewater

One-pot fabrication of SF-DA@PVDF membrane for dye adsorption and oil-in-water emulsion separation

Fabrication of a superhydrophilic PVDF membrane with excellent chemical and mechanical stability for highly efficient emulsion separation

One-Step Phase Separation and Mineralization Fabrication of Membranes for Oily Wastewater Treatment

Fast fabricating superhydrophilic PVDF membrane via proanthocyanidins crosslinking at room temperature