Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

Evaluation on Elevated-Temperature Stability of Modified 718-Type Alloys with Varied Phase Configurations

Accelerating Optimization of IN718 by Mapping Alloying Effects on Phase Stabilities and Mechanical Properties Using High-Throughput Calculations

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

Thermomechanical Tensile Properties of Deposited Inconel 718 Superalloy over a Wide Range of Strain Rate and Temperature

Evaluation on static mechanical stability of wrought Inconel 718 superalloy; effect of grain configuration and δ precipitation

Effect of Annealing Treatment on Microstructure Evolution and Creep Behavior of a Multiphase Ni3Al-based Superalloy

Microstructure evolution of an Inconel 718 alloy prepared by electron beam smelting

Inconel 718 Treated with Two-Stage Solution and Aging Processes: Microstructure Evolution and Enhanced Properties

Enhancing tensile properties of wrought Ni-based superalloy ATI 718Plus at elevated temperature via morphology control of η phase

Temperature-dependent Deformation Mechanisms and Microstructural Degradation of a Polycrystalline Nickel-Based Superalloy

Effect of γ'-δ precipitates tailored by Ti3AlC2 on Inconel 718 composites: Microstructure evolution, enhanced properties and strengthening mechanism

Revealing the γ′ and γ′′ Phase Fractions of Additively Manufactured and Differently Heat‐Treated Nickel‐Base Superalloy IN718 by Atom Probe Tomography and Their Impact on Mechanical Properties

Soft Solution State and Hard Aging State of Inconel 718 Reached Via Optimized Precipitation Elements Using Cluster Formula Approach

Influence of stabilization heat treatment temperature on microstructure and stress rupture properties of Inconel 706 superalloy

Microstructure Evolution of Inconel 718 Superalloy During Hot Working and Its Recent Development Tendency

Early evolution of δ phase and coarse γ ́ ́ phase in Inconel 718 alloy with high temperature ageing

γʹ and γ′′ co-precipitation phenomena in directly aged Alloy 718 with high δ-phase fractions

Composition Optimization of Inconel 718 Via Cluster Formula and Experimental Verification

Effect of the Δ Phase on the Tensile Properties of a Nickel-Based Superalloy

Effect of the precipitation of the η-Ni3Al0.5Nb0.5 phase on the microstructure and mechanical properties of ATI 718Plus

Early evolution of phase and coarse á phase in Inconel 718 alloy with high temperature ageing