Preparing 3D-Printable Silk Fibroin Hydrogels with Robustness by a Two-Step Crosslinking Method

Dafei Gong,Qinrui Lin,Zhengzhong Shao,Xin Chen,Yuhong Yang

DOI: https://doi.org/10.1039/d0ra04789a

IF: 4.036

2020-01-01

RSC Advances

Abstract:Schematic showing the fabrication process of the 3D-printed robust double-network RSF hydrogels.

What problem does this paper attempt to address?

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

Yixian Wang,Xin Xu,Desheng Liu,Jiayu Wu,Xingxing Yang,Bin Zhu,Chufeng Sun,Pan Jiang,Xiaolong Wang

DOI: https://doi.org/10.1016/j.addma.2024.104346

IF: 11

2024-01-01

Additive Manufacturing

Abstract:Owing to flexible structural design and rapid prototyping manufacturing, 3D printable hydrogels with solid-like and fluid-like characters have emerged as a promising candidate for biomedical engineering, soft robotics, and flexible electronics. However, existing 3D printing of hydrogel place substantial constraints on hydrogel high-fidelity of the printed hydrogel complex structures due to the shape deformation and collapse caused by water evaporation. Herein, we propose a mixed solvent printing strategy followed with water dialysis to achieve vat photopolymerization 3D printing of high-fidelity hydrogel structure by restraining water evaporation. Concretely, dimethyl sulfoxide (DMSO) is introduced into the hydrogel ink as co-solvent to improve the anti-dehydration performance during 3D printing. The as-prepared gels are then transformed into hydrogels with good fidelity and excellent performance through solvent exchange and water dialysis. Enabled by these characteristics, various functional devices with complex structures are demonstrated with the present high-fidelity 3D printing of diverse hydrogels. The solvent assisted high-fidelity hydrogel 3D printing protocol combining with the compatibility to various high-performance hydrogels is believed to be promising for wearable devices, wound dressings, electronic skin, and intelligent robots.
3D freeform printing of silk fibroin

Maria J. Rodriguez,Thomas A. Dixon,Eliad Cohen,Wenwen Huang,Fiorenzo G. Omenetto,David L. Kaplan

DOI: https://doi.org/10.1016/j.actbio.2018.02.035

IF: 10.633

2018-01-01

Acta Biomaterialia

Abstract:Freeform fabrication has emerged as a key direction in printing biologically-relevant materials and structures. With this emerging technology, complex structures with microscale resolution can be created in arbitrary geometries and without the limitations found in traditional bottom-up or top-down additive manufacturing methods. Recent advances in freeform printing have used the physical properties of microparticle-based granular gels as a medium for the submerged extrusion of bioinks. However, most of these techniques require post-processing or crosslinking for the removal of the printed structures (Miller et al., 2015; Jin et al., 2016) [1], [2]. In this communication, we introduce a novel method for the one-step gelation of silk fibroin within a suspension of synthetic nanoclay (Laponite) and polyethylene glycol (PEG). Silk fibroin has been used as a biopolymer for bioprinting in several contexts, but chemical or enzymatic additives or bulking agents are needed to stabilize 3D structures. Our method requires no post-processing of printed structures and allows for in situ physical crosslinking of pure aqueous silk fibroin into arbitrary geometries produced through freeform 3D printing.
Research Progress on Gelling Mechanism and Modification of Silk Fibroin Hydrogels

Di Liu,Zongpu Xu,Mingying Yang,Liangjun Zhu

DOI: https://doi.org/10.13441/j.cnki.cykx.2018.01.022

2018-01-01

Abstract:Hydrogel materials are of great value in medical field due to their similarity to human soft tissue.With silk fibroin as raw materials,organic solvent induction method can be employed to shorten the gelling time of silk fibroin to several hours.Silk fibroin/collagen composite hydrogel prepared with carbodiimide (EDC) as activation cross-linking agent has a storage modulus of up to 10 kPa.In vivo experiments indicate that silk fibroin hydrogel created by enzymatic crosslinking has good biocompatibility and biodegradability.We first explain the gelling mechanism of silk fibroin hydrogels,and then systematically introduce the research progress on preparation and modification methods of various silk fibroin hydrogels.Besides,potential applications of silk fibroin hydrogels as novel biomaterial in clinical applications are analyzed.Basic theoretical and technological issues to be solved for clinical applications of silk fibroin hydrogels are also discussed.
Design of Multistimuli Responsive Hydrogels Using Integrated Modeling and Genetically Engineered Silk–Elastin‐Like Proteins

Wenwen Huang,Anna Tarakanova,Nina Dinjaski,Qin Wang,Xiaoxia Xia,Ying Chen,Joyce Y. Wong,Markus J. Buehler,David L. Kaplan

DOI: https://doi.org/10.1002/adfm.201600236

IF: 19

2016-01-01

Advanced Functional Materials

Abstract:Elastomeric, robust, and biocompatible hydrogels are rare, while the need for these types of biomaterials in biomedical-related uses remains high. Here, a new family of genetically engineered silk-elastin copolymers (SELPs) with encoded enzymatic crosslinking sites is developed for a new generation of stimuli-responsive yet robust hydrogels. Input into the designs is guided by simulation, and realized via genetic engineering strategies. The avoidance of gamma irradiation or chemical crosslinking during gel fabrication, in lieu of an enzymatic process, expands the versatility of these new gels for the incorporation of labile proteins and cells. In the present study, the new SELP hydrogels offers sequence dependent, reversible stimuli-responsive features. Their stiffness covers almost the full range of the elasticity of soft tissues. Further, physical modification of the silk domains provided a secondary control point to fine-tune mechanical stiffness while preserving stimuli-responsive features, with implications for a variety of biomedical materials and device needs.
Strong and Ultra-Tough Supramolecular Hydrogel Enabled by Strain-Induced Microphase Separation

Jiayu Wu,Zhixing Zhang,Zhenyuan Wu,Desheng Liu,Xingxing Yang,Yixian Wang,Xin Jia,Xin Xu,Pan Jiang,Xiaolong Wang

DOI: https://doi.org/10.1002/adfm.202210395

IF: 19

2022-01-01

Advanced Functional Materials

Abstract:Architected hydrogels are widely used in biomedicine, soft robots, and flexible electronics while still possess big challenges in strong toughness, and shape modeling. Here, inspired with the universal hydrogen bonding interactions in biological systems, a strain-induced microphase separation path toward achieving the printable, tough supramolecular polymer hydrogels by hydrogen bond engineering is developed. Specifically, it subtly designs and fabricates the poly (N-acryloylsemicarbazide-co-acrylic acid) hydrogels with high hydrogen bond energy by phase conversion induced hydrogen bond reconstruction. The resultant hydrogels exhibited the unique strain-induced microphase separation behavior, resulting in the excellent strong toughness with, for example, an ultimate stress of 9.1 +/- 0.3 MPa, strain levels of 1020 +/- 126%, toughness of 33.7 +/- 6.6 MJ m(-3), and fracture energy of 171.1 +/- 34.3 kJ m(-2). More importantly, the hydrogen bond engineered supramolecular hydrogels possess dynamic shape memory character, i.e shape fixing at low temperature while recovery after heating. As the proof of concept, the tailored hydrogel stents are readily manufactured by 3D printing, which showed good biocompatibility, load-bearing and drug elution, being beneficial for the biomedical applications. It is believed that the present 3D printing of the architected dynamic hydrogels with ultrahigh toughness can broaden their applications.
Fabrication and characterization of porous tubular silk fibroin scaffolds.

Sijia Min,Xin Gao,Lin Liu,Li Tian,Liangjun Zhu,Haiping Zhang,Juming Yao

DOI: https://doi.org/10.1163/156856208X396056

2012-01-01

Abstract:Silk fibroin (SF) has been one of promising resources of biotechnology and biomedical materials due to its unique properties. Here, different sizes of porous tubular scaffolds were fabricated from a SF aqueous solution with the addition of poly(ethylene glycol diglycidyl ether) (PGDE). The scaffolds were generally flexible and transparent at the wet state with a pore size of 81-128 mu m and porosity of 90-96%, depending on the concentrations of SF and PGDE. The mechanical properties measurement showed that the tubular SF scaffolds had satisfying tensile and compression properties, especially the excellent deformation-recovery ability. FT-IR spectra indicated that the SF in the tubular scaffolds was in a beta-sheet structure, and no PGDE characteristic band was observed, suggesting that the PGDE could be removed from the scaffolds by soaking in deionized water. The cell compatibility of scaffolds was evaluated, and no obvious cytotoxicity to mouse L-929 fibroblasts was detected. (C) Koninklijke Brill NV, Leiden, 2009
Preparation of a Novel Regenerated Silk Fibroin-Based Hydrogel for Extrusion Bioprinting.

Ni Chen,Xinbo Zhang,Jinyang Lyu,Guanglei Zhao,Kai Gu,Jun Xia,Zhongchun Chen,Zhengzhong Shao

DOI: https://doi.org/10.1039/d2sm00984f

IF: 4.046

2022-01-01

Soft Matter

Abstract:Three-dimensional (3D) bioprinting technology, allowing rapid prototyping and personalized customization, has received much attention in recent years, while regenerated silk fibroin (RSF) has also been widely investigated for its excellent biocompatibility, processibility, and comprehensive mechanical properties. However, due to the difficulty in curing RSF aqueous solution and the tendency of conformational transition of RSF chains under shearing, it is rather complicated to fabricate RSF-based materials with high mechanical strength through extrusion bioprinting. To solve this problem, a printable hydrogel with thixotropy was prepared from regenerated silk fibroin with high-molecular-weight (HMWRSF) combined with a small amount of hydroxypropyl methylcellulose (HPMC) in urea containing aqueous solution. It was found that the introduction of urea could not only vary the solid content of the hydrogel to benefit the mechanical properties of the 3D-bioprinted pre-cured hydrogels or 3D-bioprinted sponges, but also expand the "printable window" of this system. Indeed, the printability and rheological properties could be modulated by varying the solid content, the heating time, the urea/HMWRSF weight ratio, etc. Moreover, the microstructure of nanospheres stacked in these lyophilized 3D-bioprinted sponges was interesting to observe, which indicated the existence of microhydrogels and both "the reversible network" and "the irreversible network" in this HMWRSF-based pre-cured hydrogel. Like other HMWRSF materials fabricated in other ways, these 3D-bioprinted HMWRSF-based sponges exhibited good cytocompatibility for dental pulp mesenchymal stem cells. This work may inspire the design of functional HMWRSF-based materials by regulating the relationship between structure and properties.
Dual Ionically Cross-linked Double-Network Hydrogels with High Strength, Toughness, Swelling Resistance, and Improved 3D Printing Processability

Xuefeng Li,Hui Wang,Dapeng Li,Shijun Long,Gaowen Zhang,ZiLiang Wu

DOI: https://doi.org/10.1021/acsami.8b13038

IF: 9.5

2018-01-01

ACS Applied Materials & Interfaces

Abstract:We report a dual ionic cross-linking approach for the preparation of double-network hydrogels with robustness, high strength, and toughness, sodium alginate/poly(acrylamide-co-acrylic acid)/Fe3+ (SA/P(AAm-co-AAc)/Fe3+), in a facile "one-step" dual ionic cross-linking method. We take advantage of the abundant carboxyl groups on alginate molecules and the copolymer chains and their high coordination capacity with multivalent metal ions to obtain hydrogels with high strength and toughness. The optimal SA/P(AAm-co-AAc)/Fe3+ (SA 2 wt % and AAc S mol %) hydrogels showed a remarkable mechanical performance with 3.24 MPa tensile strength and 1228% strain, both of which remained stable with 76% water content and were highly swelling resistant in an aqueous environment. The hydrogels possessed high fatigue resistance, self recovery, pH-triggered healing capability, shape memory, and reversible gel sol transition facilitated by pH regulation. Moreover, they show three-dimensional (3D) printing processability by properly adjusting the solution viscosity. The approach may provide a convenient way of obtaining hydrogels having high strength and toughness with a number of desirable properties for a broad range of biomedical applications.
Enhancing Mechanical Properties of Silk Fibroin Hydrogel Through Restricting the Growth of Β-Sheet Domains

Dihan Su,Meng Yao,Jie Liu,Yiming Zhong,Xin Chen,Zhengzhong Shao

DOI: https://doi.org/10.1021/acsami.7b04623

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:Usually, regenerated silk fibroin (RSF) hydrogels cross-linked by chemical agents such as horseradish peroxide (HRP)/H2O2 perform elastic properties, while display unsatisfactory strength for practical applications especially as load-bearing materials, and inadequate stability when incubated in a simulated in vivo environment. Here, the RSF hydrogel with both excellent strength and elasticity was prepared by inducing the conformation transition from random coil to β-sheet in a restricted RSF network precross-linked by HRP/H2O2. Such "dual-networked" hydrogels, regarding the one with 10 wt % RSF (Mw: 220 kDa) as a representative, show around 100% elongation, as well as the compressive modulus and tensile modulus up to 3.0 and 2.5 MPa respectively, which are much higher than those of physically cross-linked natural polymer hydrogels (commonly within 0.01-0.1 MPa at the similar solid content). It has been shown that the enhanced comprehensive mechanical properties of RSF hydrogels derive from the formation of small-sized and uniformly distributed β-sheet domains in the hydrogel during the conformation transition of RSF whose size is limited by the first network formed by cross-linkers with HRP/H2O2. Importantly, the tough RSF hydrogel changes the normally weak recognition of various RSF hydrogels and holds a great potential to be the material in biomedical field because it seems to be very promising regarding its biocompatibility, biodegradability, etc.
Three-dimensional Printing of Photocrosslinked Self-supporting Silk Fibroin Hydrogels

Yi Huang,Lingling Lyu,Xiaopeng Pan,Guangdong Sun,Yongqiang Li,Juming Yao,Jianzhong Shao

DOI: https://doi.org/10.7503/cjcu20210841

2022-01-01

Abstract:As a biological macromolecular material degummed from silk fiber,silk fibroin(SF)is considered to be an ideal candidate for bioink components in three-dimensional(3D)bioprinting because of its excellent biocompatibility, biodegradability and tunable mechanical properties. However,the conventional silk fibroin crosslinking methods cannot meet the requirements of 3D printing on the real-time forming efficiency and biocompatibility. In order to realize the 3D rapid prototyping of silk fibroin,the in-situ photocrosslinking processing technology of self-supporting silk fibroin hydrogel was proposed by combining the blue light-induced self-crosslinking method with 3D extruded printing technology. The basic rheological properties,photocrosslinking properties and moulding processability of silk fibroin solution were studied by using rotary rheometer,photorheological test system and modified 3D extruded printing equipment. The results showed that the silk fibroin solution(<20%,mass fraction)was mainly characterized by viscidity,and its inadequate structural strength and stability cannot meet the requirements of 3D extruded printing for material formability,shape retention and printing accuracy. Rapid photocrosslinking molding processing of silk fibroin hydrogel can be achieved by light-induced self-crosslinking in the presence of tris(2,2-bipyridyl)ruthenium (II)chloride hexahydrate[Ru(II)]and potassium persulfate(KPS)as blue light initiators. Tyrosine residues on adja??? cent SF macromolecular chains can be oxidized into tyrosine free radicals under the action of excited active species, and then coupled and crosslinked into di-tyrosine structure. Photocrosslinking behavior of silk fibroin under blue light irradiation conformed to exponential growth model. Due to the"filter effect"of the photosensitizer on the incident light,silk fibroin solution showed the optimized photocrosslinking performance when the dose of the photosensitizer Ru(II)was 0.05 mmol/L. By further adjusting the parameters such as air pressure,needle aperture,moving speed and curing rate,semi-transparent and micro-elastic silk fibroin hydrogel can be printed in real time by 3D extruded printing equipment under continuous blue light irradiation. The efficient and accurate construction of silk fibroin gel materials from single-layer geometric structure to multi-layer three-dimensional network structure can be realized, which provides a new idea for biological 3D printing of self-supporting silk fibroin gel materials.
Dityrosine-inspired photocrosslinking technique for 3D printing of silk fibroin-based composite hydrogel scaffolds

Yi Huang,Guangdong Sun,Lingling Lyu,Yongqiang Li,Dapeng Li,Qinguo Fan,Juming Yao,Jianzhong Shao

DOI: https://doi.org/10.1039/d1sm01817e

IF: 4.046

2022-01-01

Soft Matter

Abstract:Photoinduced self-crosslinking technology is a great facilitator of 3D bioprinting of silk fibroin (SF) by allowing rapid solidification of a deliberately formulated SF-based photocrosslinkable bioink. An SF-based, photocrosslinked hydrogel was fabricated with tyramine-modified sodium carboxymethyl cellulose (CMC-Na) as a co-crosslinkable constituent and Ru(bpy)(3)Cl-2 (Ru(ii)) and potassium persulfate (KPS) as blue light photoinitiators. Photorheological studies demonstrated that the photocrosslinking and viscoelasticity of the composite could be tuned by varying the relative content of the two constituents. Xanthan gum (XG) was employed in formulating the SF-based photocrosslinkable bioink, and the improved rheological properties and printability were evidenced by the resulting tunable shear-thinning behavior and shear thixotropy. 3D SF-based hydrogel scaffolds with uniform pores with a size of approximately 550 mu m x 1000 mu m were constructed via extrusion-based printing and a simple 30 s post-photocrosslinking combined process. Furthermore, the CMC-Na incorporated 3D hydrogel scaffolds exhibited sufficient structural strength, adequate filament fineness, and tunable transparency, which shows a promising prospect in the application of tissue engineering and regenerative medicine.
Micro/nanofabrication of Brittle Hydrogels Using 3D Printed Soft Ultrafine Fiber Molds for Damage-Free Demolding.

Shang Lv,Jing Nie,Qing Gao,Chaoqi Xie,Luyu Zhou,Jingjiang Qiu,Jianzhong Fu,Xin Zhao,Yong He

DOI: https://doi.org/10.1088/1758-5090/ab57d8

2020-01-01

Biofabrication

Abstract:Hydrogels are very popular in biomedical areas for their extraordinary biocompatibility. However, most bio-hydrogels are too brittle to perform micro/nanofabrication. An effective method is cast molding; yet during this process, many defects occur as the excessive demolding stress damages the brittle hydrogels. Here, we propose a brand-new damage-free demolding method and a soft ultrafine fiber mold (SUFM) to replace the traditional mold. Both mechanical and finite element analysis (FEA) reveal that SUFMs have obvious advantages especially when the contact area between hydrogel and mold gets larger. By means of a high-resolution 3D printing called electrohydrodynamic (EHD) printing, SUFMs with various topological structures can be achieved with the fiber diameter ranging from 500 nm to 100 μm, at a low cost. Microfluidics and cell patterns are implemented as the demonstration for potential applications. Owing to the tiny scale of microstructures and the hydrophilicity of hydrogels, significant capillary effect occurs which can be utilized to deliver liquid and cells autonomously and to seed cells into those ultrafine channels evenly. The results open up a new avenue for a wider use of hydrogels in biomedical devices, tissue engineering, hydrogel-based microfluidics and wearable electronics; the proposed fabrication method also has the potential to become a universal technique for micro/nanofabrication of brittle materials.
Feedback in clinical education, part I: Characteristics of feedback provided by approved clinical instructors.

Sara L. Nottingham,Jolene M. Henning

DOI: https://doi.org/10.4085/1062-6050-48.6.14

2014-02-05

Journal of Athletic Training

Abstract:CONTEXT Providing students with feedback is an important component of athletic training clinical education; however, little information is known about the feedback that Approved Clinical Instructors (ACIs; now known as preceptors) currently provide to athletic training students (ATSs). OBJECTIVE To characterize the feedback provided by ACIs to ATSs during clinical education experiences. DESIGN Qualitative study. SETTING One National Collegiate Athletic Association Division I athletic training facility and 1 outpatient rehabilitation clinic that were clinical sites for 1 entry-level master's degree program accredited by the Commission on Accreditation of Athletic Training Education. PATIENTS OR OTHER PARTICIPANTS A total of 4 ACIs with various experience levels and 4 second-year ATSs. DATA COLLECTION AND ANALYSIS Extensive field observations were audio recorded, transcribed, and integrated with field notes for analysis. The constant comparative approach of open, axial, and selective coding was used to inductively analyze data and develop codes and categories. Member checking, triangulation, and peer debriefing were used to promote trustworthiness of the study. RESULTS The ACIs gave 88 feedback statements in 45 hours and 10 minutes of observation. Characteristics of feedback categories included purpose, timing, specificity, content, form, and privacy. CONCLUSIONS Feedback that ACIs provided included several components that made each feedback exchange unique. The ACIs in our study provided feedback that is supported by the literature, suggesting that ACIs are using current recommendations for providing feedback. Feedback needs to be investigated across multiple athletic training education programs to gain more understanding of certain areas of feedback, including frequency, privacy, and form.
High‐Strength, Durable All‐Silk Fibroin Hydrogels with Versatile Processability Toward Multifunctional Applications

Zhenghua Zhu,Shengjie Ling,Jingjie Yeo,Siwei Zhao,Lorenzo Tozzi,Markus J. Buehler,Fiorenzo Omenetto,Chunmei Li,David L. Kaplan

DOI: https://doi.org/10.1002/adfm.201704757

IF: 19

2018-01-01

Advanced Functional Materials

Abstract:Hydrogels are the focus of extensive research due to their potential use in fields including biomedical, pharmaceutical, biosensors, and cosmetics. However, the general weak mechanical properties of hydrogels limit their utility. Here, pristine silk fibroin (SF) hydrogels with excellent mechanical properties are generated via a binary‐solvent‐induced conformation transition (BSICT) strategy. In this method, the conformational transition of SF is regulated by moderate binary solvent diffusion and SF/solvent interactions. β‐sheet formation serves as the physical crosslinks that connect disparate protein chains to form continuous 3D hydrogel networks, avoiding complex chemical and/or physical treatments. The Young's modulus of these new BSICT–SF hydrogels can reach up to 6.5 ± 0.2 MPa, tens to hundreds of times higher than that of conventional hydrogels (0.01–0.1 MPa). These new materials fill the “empty soft materials' space” in the elastic modulus/strain Ashby plot. More remarkably, the BSICT–SF hydrogels can be processed into different constructions through different polymer and/or metal‐based processing techniques, such as molding, laser cutting, and machining. Thus, these new hydrogel systems exhibit potential utility in many biomedical and engineering fields.
Investigation on the Structure and Mechanical Properties of Highly Tunable Elastomeric Silk Fibroin Hydrogels Cross-Linked by γ-Ray Radiation.

Nier Wu,Huilei Yu,Muyang Sun,Zong Li,Fengyuan Zhao,Yingfang Ao,Haifeng Chen

DOI: https://doi.org/10.1021/acsabm.9b01062

2020-01-01

ACS Applied Bio Materials

Abstract:Silk fibroin (SF) is a natural polymer with low immunogenicity and good biocompatibility. However, most silk-based hydrogels formed through chemical or physical cross-linking are brittle, the preparation of which also inevitably introduces cytotoxic cross-linking agents. Herein, a simple strategy is presented for synthesizing SF hydrogels with tunable mechanical properties by combining γ-ray radiation with ethanol treatment. Neither toxic initiators nor chemical agents are utilized during the whole preparation procedure. For "soft" hydrogels, the compressive moduli are less than 29 kPa (SF-S hydrogels), while for "tough" hydrogels, the compressive moduli are between 1.21 and 2.41 MPa (SF-D hydrogels). Specifically, γ-ray radiation makes SF form uniform and stable chemical cross-linking sites within and between molecular chains, resulting in "soft" and highly elastic SF hydrogels. The physical cross-linking via ethanol treatment leads to the self-assembly of fibroin chains, transforming those soft hydrogels to tough hydrogels. These double cross-linked SF hydrogels (SF-D hydrogels) exhibit excellent mechanical strength. Effects of various cross-linking conditions on the secondary structure, pore structure, mechanical properties, gelation degree, swelling, and in vitro degradation properties are explored. A series of cell experiments demonstrate that the SF hydrogels with different mechanical strength can stimulate the expression of specific genes of rat bone marrow mesenchymal stem cells (BMSCs) in various differentiation directions. These results also show the application prospects in tissue engineering by customizing hydrogels for the mechanical strength of different tissues.
Long-Lasting Thixotropic Natural Polymeric Hydrogel Based on Silk Nanofibrils.

Ling Chen,Liangyan Sun,Wen Liu,Jinrong Yao,Zhengzhong Shao,Bingjiao Zhao,Xin Chen

DOI: https://doi.org/10.1021/acsbiomaterials.3c00574

2023-01-01

ACS Biomaterials Science & Engineering

Abstract:Hydrogels are considered to be ideal biomedical materials as their physical properties are similar to the physiological tissue environment. In particular, thixotropic hydrogels have received increasing attention from researchers because of their injectability. Herein, a simple and rapid method was developed for the preparation of a regenerated silk fibroin (RSF) hydrogel with long-lasting and excellent thixotropy. The thixotropic RSF hydrogel was readily formed by ultrasonic treatment of the pretreated RSF solution for 2 min followed by incubation at 40 °C for 10 min. The storage modulus of the RSF hydrogels recovered to more than 90% of the original value within 20 s after withstanding 1000% shear strain. By avoiding complicated chemical or physical treatments and by addition of crosslinking agents and/or other chemical components, the obtained RSF hydrogels maintained excellent biocompatibility. Hence, the cells implanted inside the hydrogel can grow and proliferate normally. By virtue of ultrasonic treatment during the preparation, functional nanoparticles can be uniformly dispersed in the RSF solution to prepare RSF-based hybrid hydrogels with various functions. As an application example, hydroxyapatite (HAP) with osteoinductivity was mixed with RSF solution to prepare the RSF/HAP hybrid hydrogel. The RSF/HAP hybrid hydrogel maintained biocompatibility and thixotropy of the original RSF hydrogel and promoted osteoblastic differentiation of cells owing to the addition of HAP. Therefore, the RSF hydrogel prepared in this work has a strong application prospect in the biomedical field including, but not limited to, bone repair.
Robust Silk Protein Hydrogels Made by a Facile One-Step Method and Their Multiple Applications

Ling Chen,Liangyan Sun,Jinrong Yao,Bingjiao Zhao,Zhengzhong Shao,Xin Chen

DOI: https://doi.org/10.1021/acsabm.2c00354

2022-01-01

ACS Applied Bio Materials

Abstract:Silk fibroin is a natural polymer that has various material forms and wide applications. Hydrogel is one of the most attractive silk materials because of its hydrophilicity, biocompatibility, and flexibility. However, its applications are still quite limited because they have a complicated preparation process and/or low mechanical strength. Herein, a simple way to prepare tough silk fibroin hydrogels via a solvent-exchange method is introduced. The degummed silk fiber was directly dissolved in a calcium chloride/formic acid solution and then water was used to replace the solvent. The silk fibroin hydrogel that was obtained using this facile method exhibited even better mechanical properties than most silk fibroin hydrogels that have been reported in the literature. Also, the silk fibroin hydrogel maintained biocompatibility that was as good as that prepared via other methods. Finally, the possibility of using this regenerated silk fibroin hydrogel as a multi-functional platform (such as a catalyst carrier, photothermal agent, and underwater adhesive) has been discussed. Therefore, such a natural, sustainable, robust, and good biocompatible silk fibroin hydrogel that is prepared by an improved method may have great potential for further applications.
Preparation of silk fibroin/hyaluronic acid hydrogels with enhanced mechanical performance by a combination of physical and enzymatic crosslinking

Xiaohang Qu,Ling Yan,Shuang Liu,Yunfei Tan,Jing Xiao,Yuan Cao,Ke Chen,Wenqian Xiao,Bo Li,Xiaoling Liao

DOI: https://doi.org/10.1080/09205063.2021.1932070

2021-06-24

Abstract:<span>Silk fibroin (SF) from <i>Bombyx mori</i> is a natural polymer with exceptional biocompatibility, low immunogenicity, and ease of processability. SF-based hydrogels have been identified as one of the most attractive candidate scaffolds for tissue engineering and can be fabricated through various physical or chemical crosslinking approaches. However, conventional SF hydrogels may suffer from several major drawbacks, such as structural inhomogeneity, poor mechanical properties or utilization of cytotoxic reagents. Herein, a dually crosslinked SF-based composite hydrogel with enhanced strength and elasticity was fabricated by inducing the formation of uniform and small β-sheet structures by sonication in a restricted enzymatic precrosslinked network. The composite hydrogel not only demonstrated concentration-dependent stiffness variation but also exhibited time-dependent changes in toughness behavior. Moreover, subsequent experimental results revealed that the hydrogels exhibit other advantages, including high water retention capacity and long-term stability under physiological conditions. Finally, a three-dimensional (3 D) construct of the cell-laden hydrogel was fabricated, confirming that the composite hydrogel could provide a biocompatible microenvironment with dynamically changing mechanical properties. The combination of physical and enzymatic crosslinking strategies contributes to a biocompatible composite hydrogel with unique mechanical properties that holds great potential for use in tissue engineering and regenerative medicine.</span>

engineering, biomedical,materials science, biomaterials,polymer science
Fabrication of Silk Hydrogel Scaffolds with Aligned Porous Structures and Tunable Mechanical Properties

Zewu Jiang,Qingqing Sun,Qian Li,Xiaomeng Li

DOI: https://doi.org/10.3390/gels9030181

IF: 4.6

2023-02-25

Gels

Abstract:The effectiveness of cell culture and tissue regeneration largely depends on the structural and physiochemical characteristics of tissue-engineering scaffolds. Hydrogels are frequently employed in tissue engineering because of their high-water content and strong biocompatibility, making them the ideal scaffold materials for simulating tissue structures and properties. However, hydrogels created using traditional methods have low mechanical strength and a non-porous structure, which severely restrict their application. Herein, we successfully developed silk fibroin glycidyl methacrylate (SF-GMA) hydrogels with oriented porous structures and substantial toughness through directional freezing (DF) and in situ photo-crosslinking (DF-SF-GMA). The oriented porous structures in the DF-SF-GMA hydrogels were induced by directional ice templates and maintained after photo-crosslinking. The mechanical properties, particularly the toughness, of these scaffolds were enhanced compared to the traditional bulk hydrogels. Interestingly, the DF-SF-GMA hydrogels exhibit fast stress relaxation and variable viscoelasticity. The remarkable biocompatibility of the DF-SF-GMA hydrogels was further demonstrated in cell culture. Accordingly, this work reports a method to prepare tough SF hydrogels with aligned porous structures, which can be extensively applied to cell culture and tissue engineering.

polymer science
Investigation On The Structure And Mechanical Properties Of Highly Tunable Elastomeric Silk Fibroin Hydrogels Cross-Linked By Gamma-Ray Radiation

Nier Wu,Huilei Yu,Muyang Sun,Zong Li,Fengyuan Zhao,Yingfang Ao,Haifeng Chen

DOI: https://doi.org/10.1021/acsabm.9b01062

2020-01-01

ACS Applied Bio Materials

Abstract:Silk fibroin (SF) is a natural polymer with low immunogenicity and good biocompatibility. However, most silk-based hydrogels formed through chemical or physical cross-linking are brittle, the preparation of which also inevitably introduces cytotoxic cross-linking agents. Herein, a simple strategy is presented for synthesizing SF hydrogels with tunable mechanical properties by combining gamma-ray radiation with ethanol treatment. Neither toxic initiators nor chemical agents are utilized during the whole preparation procedure. For "soft" hydrogels, the compressive moduli are less than 29 kPa (SF-S hydrogels), while for "tough" hydrogels, the compressive moduli are between 1.21 and 2.41 MPa (SF-D hydrogels). Specifically, gamma-ray radiation makes SF form uniform and stable chemical cross-linking sites within and between molecular chains, resulting in "soft" and highly elastic SF hydrogels. The physical cross-linking via ethanol treatment leads to the self-assembly of fibroin chains, transforming those soft hydrogels to tough hydrogels. These double cross-linked SF hydrogels (SF-D hydrogels) exhibit excellent mechanical strength. Effects of various cross-linking conditions on the secondary structure, pore structure, mechanical properties, gelation degree, swelling, and in vitro degradation properties are explored. A series of cell experiments demonstrate that the SF hydrogels with different mechanical strength can stimulate the expression of specific genes of rat bone marrow mesenchymal stem cells (BMSCs) in various differentiation directions. These results also show the application prospects in tissue engineering by customizing hydrogels for the mechanical strength of different tissues.

Preparing 3D-Printable Silk Fibroin Hydrogels with Robustness by a Two-Step Crosslinking Method

Dimethyl Sulfoxide Mediated High-Fidelity 3D Printing of Hydrogels

3D freeform printing of silk fibroin

Research Progress on Gelling Mechanism and Modification of Silk Fibroin Hydrogels

Design of Multistimuli Responsive Hydrogels Using Integrated Modeling and Genetically Engineered Silk–Elastin‐Like Proteins

Strong and Ultra-Tough Supramolecular Hydrogel Enabled by Strain-Induced Microphase Separation

Fabrication and characterization of porous tubular silk fibroin scaffolds.

Preparation of a Novel Regenerated Silk Fibroin-Based Hydrogel for Extrusion Bioprinting.

Dual Ionically Cross-linked Double-Network Hydrogels with High Strength, Toughness, Swelling Resistance, and Improved 3D Printing Processability

Enhancing Mechanical Properties of Silk Fibroin Hydrogel Through Restricting the Growth of Β-Sheet Domains

Three-dimensional Printing of Photocrosslinked Self-supporting Silk Fibroin Hydrogels

Dityrosine-inspired photocrosslinking technique for 3D printing of silk fibroin-based composite hydrogel scaffolds

Micro/nanofabrication of Brittle Hydrogels Using 3D Printed Soft Ultrafine Fiber Molds for Damage-Free Demolding.

Feedback in clinical education, part I: Characteristics of feedback provided by approved clinical instructors.

High‐Strength, Durable All‐Silk Fibroin Hydrogels with Versatile Processability Toward Multifunctional Applications

Investigation on the Structure and Mechanical Properties of Highly Tunable Elastomeric Silk Fibroin Hydrogels Cross-Linked by γ-Ray Radiation.

Long-Lasting Thixotropic Natural Polymeric Hydrogel Based on Silk Nanofibrils.

Robust Silk Protein Hydrogels Made by a Facile One-Step Method and Their Multiple Applications

Preparation of silk fibroin/hyaluronic acid hydrogels with enhanced mechanical performance by a combination of physical and enzymatic crosslinking

Fabrication of Silk Hydrogel Scaffolds with Aligned Porous Structures and Tunable Mechanical Properties

Investigation On The Structure And Mechanical Properties Of Highly Tunable Elastomeric Silk Fibroin Hydrogels Cross-Linked By Gamma-Ray Radiation