Abstract:The current research about the flow ripple of axial piston pump mainly focuses on the effect of the structure of parts on the flow ripple. Therein, the structure of parts are usually designed and optimized at rated working conditions. However, the pump usually has to work in large-scale and time-variant working conditions. Therefore, the flow ripple characteristics of pump and analysis for its test accuracy with respect to variant steady-state conditions and transient conditions in a wide range of operating parameters are focused in this paper. First, a simulation model has been constructed, which takes the kinematics of oil film within friction pairs into account for higher accuracy. Afterwards, a test bed which adopts Secondary Source Method is built to verify the model. The simulation and tests results show that the angular position of the piston, corresponding to the position where the peak flow ripple is produced, varies with the different pressure. The pulsating amplitude and pulsation rate of flow ripple increase with the rise of pressure and the variation rate of pressure. For the pump working at a constant speed, the flow pulsation rate decreases dramatically with the increasing speed when the speed is less than 27.78% of the maximum speed, subsequently presents a small decrease tendency with the speed further increasing. With the rise of the variation rate of speed, the pulsating amplitude and pulsation rate of flow ripple increase. As the swash plate angle augments, the pulsating amplitude of flow ripple increases, nevertheless the flow pulsation rate decreases. In contrast with the effect of the variation of pressure, the test accuracy of flow ripple is more sensitive to the variation of speed. It makes the test accuracy above 96.20% available for the pulsating amplitude of pressure deviating within a range of ±6% from the mean pressure. However, with a variation of speed deviating within a range of ±2% from the mean speed, the attainable test accuracy of flow ripple is above 93.07%. The model constructed in this research proposes a method to determine the flow ripple characteristics of pump and its attainable test accuracy under the large-scale and time-variant working conditions. Meanwhile, a discussion about the variation of flow ripple and its obtainable test accuracy with the conditions of the pump working in wide operating ranges is given as well.

The Direct Measurement of the Cylinder Block Dynamic Characteristics Based on a Non-Contact Method in an Axial Piston Pump

Real-time Measurement on Lubrication Characteristic Parameters of Plane Port Pair in Axial Piston Pumps

Development And Simulation Of Lubrication Test System For Port Plate/Cylinder Block In Axial Piston Pump

Modeling and Analysis of the Tilt Behavior of the Cylinder Block in a High-Speed Axial Piston Pump

Comparison in Measurements of Lubricating Film of the Slipper-pair in Axial Piston Pumps

Modelling and Experiment Study on Fluid Character of Axial Piston Pump

Multi-position Measurement of Oil Film Thickness Within the Slipper Bearing in Axial Piston Pumps

Novel Three-Piston Pump Design for a Slipper Test Rig

Experimental Study on the Influence of the Rotating Cylinder Block and Pistons on Churning Losses in Axial Piston Pumps

Real-time Measuring Method to Measure the Micro-Displacement of a Rotating Cutter in Precise Piston Noncylinder Pinhole Boring

Investigation on the Radial Micro-Motion about Piston of Axial Piston Pump

Performance Optimization for High Speed Axial Piston Pump Considering Cylinder Block Tilt

THE TRANSITION OF WEAR AND LEAKAGE CHARACTERISTICS OF THE CYLINDER BLOCK/VALVE PLATE INTERFACE IN A WIDE RANGE OF OPERATING CONDITIONS

58812 ANALYSIS OF THE PISTON/CYLINDER PAIR OF AXIAL PISTON PUMP BASED ON VIRTUAL PROTOTYPE(Fluid-Structure Interaction in MBS)

Analysis of the Flow Dynamics Characteristics of an Axial Piston Pump Based on the Computational Fluid Dynamics Method

A Theoretical Dynamic Model to Study the Vibration Response Characteristics of an Axial Piston Pump

Optimization and experiment research of the cylinder block of the roller piston pump

Research on Wear Prediction of Piston/cylinder Pair in Axial Piston Pumps

Experimental Investigations of the Slipper Spin in an Axial Piston Pump

A Cylinder Block Dynamic Characteristics-Based Data Augmentation Method for Wear State Identification under Data Imbalance Condition

Impact of Typical Steady-State Conditions and Transient Conditions on Flow Ripple and Its Test Accuracy for Axial Piston Pump