Abstract:Coupled chemical and mechanical phenomena at electrode interfaces largely govern the reversibility and long term stability of lithium ion and lithium metal batteries. A well-known example in lithium ion batteries is the formation of the electrically insulating, ionically conductive, continuous solid electrolyte interface (SEI) on graphitic anodes, which passivates the electrode against further electrochemical reduction of the electrolyte. Unfortunately, this stable passivation does not occur in Si and Li metal anodes. High voltage cathodes are also prone to detrimental interfacial processes, resulting in electrolyte oxidation, gas formation, and transition metal dissolution. In response, a myriad of coating technologies has been developed to mitigate and control these interfacial phenomena and enable next-generation electrodes. These technologies must provide thin, conformal coatings over the entire electrochemically active surface area of the electrode; the coatings must also possess the requisite mechanical properties to accommodate volume dilation due to lithium insertion/extraction. This presentation will describe the development of conformal, compliant polymer thin film coatings for lithium battery electrodes. The polymer thin films are prepared by initiated chemical vapor deposition (iCVD), which provides exquisite control over film composition and morphology by facilitating heterogeneous free-radical polymerization of vinyl monomers with thickness precision on the order of 1 nm. Poly(1,3,5,7-tetravinyl-1,3,5,7-tetramethylcyclotetrasiloxane) (pV4D4) was deposited onto silicon thin film electrodes using iCVD. 25 nm-thick pV4D4 films on Si electrodes improved initial coulombic efficiency by 12.9% and capacity retention over 100 cycles by 64.9% relative to untreated electrodes. PV4D4 coatings also improved rate capabilities, enabling higher lithiation capacity at all current densities. Post-cycling FTIR and XPS showed that pV4D4 inhibited electrolyte reduction and altered the SEI composition, with enrichment in LiF. In another example, thin conformal coatings of perfluorinated polymer were deposited onto battery-grade Cu current collectors to function as an artificial solid electrolyte interface. The effect of the film thickness on Li cycling reversibility was characterized. By galvanostatically cycling Li in an asymmetric Li||Cu cell using 1M LiFSI in a 1:1 (v/v) mixture of dioxolane:dimethoxyethane at 30°C, it was shown that the average coulombic efficiency averaged over 50 cycles increased from 98.36% for bare, untreated Cu to 99.08% for Cu coated with 25 nm of the fluoropolymer. Moreover, the 25 nm coating suppressed interfacial impedance growth on the current collector; the resistance of the coated Cu was 40% lower than the untreated Cu after 100 cycles. The mechanism by which the polymer coating enhances coulombic efficiency and suppresses side reactions will be discussed, along with discussion of the performance in practical anode-free lithium metal batteries.

Surface Passivation of Lithium Metal Via in Situ Polymerization

The Synergistic Effect of Lithium Bis(fluorosulfonyl)imide and Lithium Nitrate for High-Performance Lithium Metal Anode

Surface Fluorination of Reactive Battery Anode Materials for Enhanced Stability.

(Invited) Lithium Battery Interfacial Engineering with Thin Conformal Polymer Coatings

Polylatic Acid Nanofiber-Guided Uniform Lithium Deposition for Stable Lithium Metal Anodes

Artificial LiF‐Rich Interface Enabled by In‐Situ Electrochemical Fluorination for Stable Lithium‐Metal Batteries

Tailoring Lithium Deposition Via an SEI‐Functionalized Membrane Derived from LiF Decorated Layered Carbon Structure

Ultrathin LiF-rich solid electrolyte interphase for stable long-life cycling stabilization of lithium metal anodes

Surface Positive-Charged Modification of Inorganic Fillers to Optimize Lithium Ion Conductive Pathways in Composite Polymer Electrolytes for Lithium-Metal Batteries

Phase-Separation-Induced Porous Lithiophilic Polymer Coating for High-Efficiency Lithium Metal Batteries

Self-Assembled Monolayer Enables Slurry-Coating of Li Anode

In-situ constructed polymer/alloy composite with high ionic conductivity as an artificial solid electrolyte interphase to stabilize lithium metal anode

PVDF-HFP/LiF Composite Interfacial Film to Enhance the Stability of Li-Metal Anodes

A polythiourea protective layer for stable lithium metal anodes

A Fluorinated, Ion-Conducting and Adaptive Supramolecular Polymer Protective Layer for Stabilizing Lithium Metal Anodes

Stabilizing a Lithium Metal Battery by an In Situ Li 2 S-modified Interfacial Layer via Amorphous-Sulfide Composite Solid Electrolyte

Lithium Metal Protection Enabled by In-Situ Olefin Polymerization for High-Performance Secondary Lithium Sulfur Batteries

Tailoring the Passivation Layer on Lithium Metal Anode and Aluminum Collector by Regulating the Solvation Structure to Enhance the Long-Term Cycling of Lithium Metal Batteries

Fluorinating Solid Electrolyte Interphase by Regulating Polymer–Solvent Interaction in Lithium Metal Batteries

Regulating Li Nucleation and Growth Heterogeneities via Near‐Surface Lithium‐Ion Irrigation for Stable Anode‐Less Lithium Metal Batteries

In Situ Formation of Polycyclic Aromatic Hydrocarbons as an Artificial Hybrid Layer for Lithium Metal Anodes