Abstract:Plasma electrolytic oxidation (PEO) was used to establish a porous metal oxide layer on various titanium and zirconium workpieces in the form of wires, porous tubes, and 3D-printed structures. The ultimate goal of the work was to create a layer with the desired characteristics over a catalyst support or metal membrane structures to improve the performance of the targeted high-temperature catalytic conversion or separation applications. In doing so, it was ensured that the PEO-treated layer could provide the desired morphology, thickness, and porosity needed for the final processing step, which is usually a conventional coating method. This addresses the limitations of ceramic structures, including their mechanical resistance, thermal resistance, and conductivity, and their potential for being functionalized and utilized for high-temperature applications. The entire experimental run was carried out using a 2 kilowatt (maximum output) AC-power source with a maximum current limit of 6.5 Ampere while applying a constant potential (potentiostatic) and monitoring the current fluctuation. Depending on the surface areas of the PEO-treated samples, the applied potential ranged from 200 V to 260 V. The surface features of the fresh and PEO-treated composites, including their morphology and phases, were studied using conventional characterization techniques such as SEM, EDX, and XRD. The time required to observe the spark discharge was shortened by tuning the PEO parameters, such as gradually increasing the applied potential. This, in turn, allowed for longer surface treatment and, eventually, more control over the surface texture. The EDX analysis of the elemental composition of the PEO-treated surface indicated that the contribution of the electrolyte-deposited components increases when increasing the voltage and is accompanied by an increase in the extent of oxidation. The titanium samples displayed relatively intense discharges, especially in comparison to the Zirconium wires. The PEO-treated samples were coated via standard wet-coating techniques.

Growth Mechanism of Titania on Titanium Substrate During the Early Stage of Plasma Electrolytic Oxidation

GDOES, XPS, and SEM with EDS analysis of porous coatings obtained on titanium after plasma electrolytic oxidation

Behaviors of Micro-Arcs, Bubbles, and Coating Growth during Plasma Electrolytic Oxidation of β-Titanium Alloy

Growth mechanisms for initial stages of plasma electrolytic oxidation coating on Al

A Mechanism for the Growth of a Plasma Electrolytic Oxide Coating on Al

Effect of plasma-electrolytic oxidation on mechanical properties of titanium coatings

Electrochemical Surface Treatment for Tailored Porous Structures

Investigation of surface morphology, structure and electrocatalytic properties for O2 evolution of titanium based IrO2+Ta2O5 coatings

Study on Discharge Characteristics and Microstructural Evolution of PEO Coatings Based on an Al/Ti Tracer Substrate

Fabrication of High Temperature Oxidation Resistance Nanocomposite Coatings on PEO Treated TC21 Alloy

Enhancing PEO coating on TC6 alloy through in-situ synthesis of MoSe 2 —Towards more efficient wear-reducing lubrication and wear resistance

Effects of Substrate Roughness on Microstructure and Fatigue Behavior of Plasma Electrolytic Oxidation-Coated Ti-6Al-4V Alloy

Characterization and corrosion behavior of plasma electrolytic oxidation coating on zirconium alloy in superheated steam condition

Investigation on the mechanism and properties of HA/TiO2 composite coatings with selecting Ca/P contents by plasma electrolytic oxidation

Nature of the growth of plasma electrolyte oxidation coating on Aluminum

Growth mechanism of oxide layer on Ti-6Al-4 V substrate with different surface topographies during the early stage of micro-arc oxidation

Characteristics of Hydroxyapatite-Modified Coatings Based on TiO2 Obtained by Plasma Electrolytic Oxidation and Electrophoretic Deposition

Use of Organic Acids as Additives for Plasma Electrolytic Oxidation (PEO) of Titanium

Corrosion behavior of ZrO2-TiO2 composite coatings produced on titanium alloy via plasma electrolytic oxidation

Influence of electrolyte components on the microstructure and growth mechanism of plasma electrolytic oxidation coatings on 1060 aluminum alloy

Fabrication of ultra-low porosity plasma electrolytic oxidation coating on Ta-12W alloys and its formation mechanism