Abstract:The reuse of recycled waste plastics has long been attempted in pavement engineering as bitumen modifier. It was revealed that waste plastics can significantly enhance the high-temperature performance of bitumen and bitumen mixtures. Even so, the application of waste plastics as a bitumen modifier is still not widespread. This is attributable to the generally poor low-temperature performance of plastic-modified bitumen, which often fails to meet specification requirements. For this purpose, styrene butadiene rubber (SBR) was selected to improve the low-temperature performance of plastic-modified bitumen. However, due to the long-term aging process, the composite and structure of the modified bitumen will change, which negatively impacts its performance. The objective of this study is to investigate the long-term aging behavior of plastic/SBR composite-modified bitumen. For this purpose, waste polyethylene was used as a plastic modifier and was mixed with base bitumen and 3% SBR at ratios 4.5%, 6% and 7.5%. The rheological properties and molecular weight distribution of base bitumen, plastic and plastic/SBR-modified bitumen before and after long-term aging were measured. Results show that the incorporation of plastic can improve the complex modulus, rutting factor and percent recovery of bitumen and reduce the non-recoverable creep compliance of the bitumen, indicating the modification process enhances the high-temperature performance of bitumen. The enhancement effect is more pronounced with the increase of plastic content. For modified bitumen with 7.5% plastic modifier, the complex modulus of modified bitumen is increased by 1127.55% compared to base bitumen. The addition of 3% SBR modifier can further improve the high-temperature performance of the modified bitumen. In addition, the modification process also increases the large molecule size percentage (LMSP) and weight average molecular weight of bitumen. Compared with weight average molecular weight, the LMSP correlates well with the rheological properties of modified bitumen. In accordance with the complex modulus, using the LMSP and weight average molecular weight of bitumen before and after aging, the corresponding aging index was calculated. The quantitative results showed that the addition of plastic modifier can improve the aging resistance of bitumen, but the enhancement effect is not as obvious as that of SBR modifier.

Thermal Aging, Physico‐mechanical, Dynamic Mechanical Properties of Chlorinated Polyethylene/red Mud Composites

Effects of Hygrothermal Aging and Cyclic Compressive Loading on the Mechanical and Electrical Properties of Conductive Composites

A New Insight into Utilization of Red Mud in Poly(vinyl Chloride) Composites Via Surface Modification and Toughening Modulation to Attain Performance Optimization

Effects of Red Mud on Rheological, Crystalline, and Mechanical Properties of Red Mud/pbat Composites

High-density polyethylene composite filled with red mud: effect of coupling agent on mechanical and thermal properties

Red Mud/Polypropylene Composite with Mechanical and Thermal Properties

Preparation and characterization of red mud/liquid silicon rubber with good thermal‐stability and processability

Mechanical properties of high ductile alkali-activated fiber reinforced composites incorporating red mud under different curing conditions

Effect of Heat Oxygen Aging on Mechanical Properties and Heat Resistance of Wood Rubber Plastic Ternary Composites

Toughening Action in Marble Tailings/pvc Composite Plates: Rheological and Mechanical Properties

Recycled Polyethylene and Crumb Rubber Composites Modified Asphalt with Improved Aging Resistance and Thermal Stability

Study of the influence of accelerated aging on the physical and mechanical properties of polymer composites containing rubber, polyethylene and poly(ethylene terephthalate) waste

Acoustical, vibrational, and thermal investigations of pyrolytic carbon black reinforced natural rubber composites

Systematic Investigation of the Degradation Properties of Nitrile-Butadiene Rubber/Polyamide Elastomer/Single-Walled Carbon Nanotube Composites in Thermo-Oxidative and Hot Oil Environments

Preparation and characterization of red mud/polysulfone composite geosynthetic barrier

Synthesis and Characterization of Red Mud and Rice Husk Ash-Based Geopolymer Composites

Ageing behaviour and molecular/network structure evolution of EPDM/carbon black composites under compression and in thermal-oxidative environments

Long-Term Aging Behavior of Plastic/Styrene Butadiene Rubber (SBR) Composite Modified Bitumen

Phase morphology, mechanical, and thermal properties of fiber-reinforced thermoplastic elastomer: Effects of blend composition and compatibilization

Enhanced thermo-mechanical properties of cementitious composites via red mud-based microencapsulated phase change material: Towards energy conservation in building

Preparation and Mechanical Properties Analysis of Rare Earth Filling Ethylene‐Allene Monomer Rubber Composite