Abstract:The purpose of this study was to prepare ginkgolide B (GB) lyophilized powder for injection with excellent appearance and stable quality through a formulation screening and by optimizing the freeze-drying process. Cremophor EL as a solubilizer, PEG 400 as a latent solvent, and mannitol as an excipient were mixed to increase the solubility of GB in water to more than 18 times (about from 2.5 × 10−4 mol/L (0.106 mg/mL) to 1.914 mg/mL). Formulation screening was conducted by orthogonal design where the content of GB in the solution before lyophilization (using external standard method of HPLC) and reconstitution time after lyophilization were the two evaluation indexes. The optimized formulations were GB in an amount of 2 mg/mL, Cremophor EL in an amount of 16% (v/v), PEG 400 in an amount of 9% (v/v), mannitol in an amount of 8% (w/v), and the solution pH of 6.5. Through four single-factor experiments (GB adding order, preparation temperature of GB solution, adding amount, and adsorption time of activated carbon), the preparation process of GB solution was confirmed. The glass transition temperature of maximally GB freeze-concentrated solution was − 17.6°C through the electric resistance method. GB lyophilized powder began to collapse at − 14.0°C, and the fully collapsed temperature was − 13.0°C, which were determined by freeze-drying microscope. When the collapse temperature was determined, the primary drying temperature was obtained. Thereby, the freeze-drying curve of GB lyophilized powder was initially identified. The freeze-drying process was optimized by orthogonal design, the qualified product appearance and residual moisture content were the two evaluation indexes. The optimized process parameters and process were (1) shelf temperature, decreased from room temperature to − 45.0°C, at 0.5°C/min in 2 h; (2) shelf temperature increased from − 45.0 to − 25.0°C, at 0.1°C/min, maintained for 3 h, and the chamber pressure was held at 10 Pa; (3) shelf temperature was increased from − 25.0 to − 15.0°C at 0.1 °C/min, maintained for 4 h, and the chamber pressure was held at 10 Pa; and (4) shelf temperature was increased from − 15.0 to 20.0°C at 1.0 °C/min, maintained for 4 h, and the chamber pressure was raised up to 80 Pa. In these lyophilization process conditions, the products complied with relevant provisions of the lyophilized powders for injection. Meanwhile, the reproducibility was satisfactory. Post-freezing annealing had no significantly beneficial effects on shortening the freeze-drying cycle and improving the quality of GB lyophilized powder.

Formulation, Preparation Technique, and Quality Evaluation of Pridinol Mesylate Injection

Study on pramipexole dihydrochloride sustained-release tablets

Study on Stability of Omeprazole for Injection

Determination of Critical Influencing Factor on Ph Stability of Yuxingcao Injection

Systematic investigation for the stability of traditional Chinese medicine injection composition using Shenmai injection as a model

Stability-indicating HPLC method optimization using quality by design with design of experiments approach for quantitative estimation of organic related impurities of Doripenem in pharmaceutical formulations

Optimization of a Coupling Process for Insulin Degludec According to a Quality by Design (qbd) Paradigm

Preparation and Quality Control of Potassium Dehydroandrographolide Succinate Hollow Suppository

A Method for Quality Control of Nimodipine Microemulsion Injection

Studies on Stability of Alprostadil (Lipo-Pge1 and DN-PGE1) Targeting Preparation

Formulation Screening and Freeze-Drying Process Optimization of Ginkgolide B Lyophilized Powder for Injection

Investigation on the compatible stability of sodium tanshinone ⅡA sulfonate injection with 10 different drugs

Formulation, Optimization and Evaluation of Solid SMEDDS of Pioglitazone

A Strategy for Selecting “Q-Markers” of Chinese Medical Preparation via Components Transfer Process Analysis with Application to the Quality Control of Shengmai Injection

Preparation and Quality Control of Ascorbic Acid and Sodium Chloride Injection

Preparation and Clinical Application of Suppository Sodium Copper Chlorophyllin

Physicochemical Characterization and Pharmacological Evaluation of Novel Propofol Micelles with Low-Lipid and Low-Free Propofol

Study on the prescription and production process for the dobutamine hydrochloride glucose injection

The evidence-based formulation of the administration standards for diazepam injection

Development and In vitro and In vivo Evaluations of a Microemulsion Formulation for the Oral Delivery of Oxaprozin

Preparation of Salidroside Injection and Its Pharmacokinetics in Rats