Formation and transportation of heap in an inclined and vertically vibrated container
G. Miao,Kai Huang,Yi Yun,R. Wei
2003-01-01
Abstract:An experimental study is performed on formation and transportation of heap in granular materials in an inclined and vertically vibrated container. A relationship is presented of how the velocity of heap changing with driving acceleration and frequency. The shape of the heap bottom is measured by detecting the colliding phase of the heap bottom with the floor of container. An analogous experiment is performed with a heap-shaped Plexiglas block. Pressure gradient of ambient gas plays a crucial role in generating and maintaining a heap. Ratchet effect causes transportation of heap. It is well known that under vibration many processes, e. g. segregation, convection, heaping, etc. [1], which govern the physics of granular materials, are quite unusual, so that the properties of such materials are not well understood. For example, heaping is one of longstanding problem since Faraday. Several physical mechanisms have been identified as possible causes of heaping: Friction between the walls and particles [2], analog of acoustic streaming if the shaking is nonuniform [3], and gas pressure effect [4], etc. [5] Recently we have observed experimentally the formation of a heap and its transportation from the lower to the higher end in an inclined and vertically vibrated container. The experiments are conducted in a Plexiglas rectangular container [370 mm (length) ×25 mm (width) ×80 mm (height)]. We use two kinds of quartz sands: Spheres of diameter 0.15-0.20 mm and grains of irregular shape or coarse surface of diameter 0.3-0.5 mm. The container is inclined with the inclination α from 2.0◦ to 5.5◦ by putting a pad underneath the container (shown in Fig.1). The vibration exciter (Brüel and Kjær 4809) is driven by a sinusoidal signal, and controlled by the vibration exciter control type 1050. Driving frequency f and dimensionless acceleration amplitude Γ = 4π2f2A/g (where A is driving amplitude and g the gravitational acceleration) are used as two control parameters. Experiments show that even in the horizontal container the horizontal acceleration can cause movement of the heap. The horizontal acceleration of our exciter is 3.5% of the vertical acceleration. To eliminate the influence of the horizontal component of the driving acceleration on the movement of the heap along the length direction of the container, we adjust the direction of the container orthogonal to the horizontal component of acceleration of the exciter. The range of Γ we use is from 1.5 to 2.5, which is a good range for heap formation. At first, about 80 ml of sands are uniformly put into the lower part of the vessel. Then as Γ increased to and beyond some critical acceleration Γc, heap will form, in the meanwhile it moves upward the container. Fig.1(a) and (b) are the typical photos of heaps. In both of them the back surface is longer than the front one, while the slopes of both surface relative to horizontal are the same. The differences between two heaps are: The dynamical angle of repose of heap formed by coarse sands is larger than that formed by spherical sands; The heap formed by coarse sands completely separated from the end walls, i. e. this heap has nothing to do with the end walls completely, while the heap formed by spherical sands has a long and very thin tail behind it, and connected to the back end wall. The heaps move upward the container with a nearly uniform velocity. We measure the velocity for four different frequencies. The result is shown in Fig.2. One can see that the velocities of both heaps increase with the driving acceleration for all of frequencies, but decrease as driving frequency increases for every value of acceleration (when 2.1 < Γ < 2.5, the velocities of heap formed by spherical sands at f = 13Hz is larger than that at f = 11Hz, this may be resulted from measurement error). The velocity of heap formed by coarse sands is greater than that of heap formed by spherical sands. For example, at most situations of Γ < 1.7 the velocity of heap formed by spherical particles is below 0.05 cm/s, while that of heap formed by coarse particles is all larger than that value. And at 11 Hz the velocities of heap formed by coarse sands are much larger than that of heap formed by spherical sands. We measure the shape of the heap’s bottom by detecting the colliding phase of different parts of the heap’s bottom with the container. A pressure transducer is mounted in the middle of the floor of container, and an oscilloscope (Agilent 54810A) is used to acquire pressure signals. In our driving parameter range, heap collides with the floor of the container once a cycle [6]. Then as heap moves upward across the transducer, the collision phases of the specified points at the heap’s bottom with the transducer relative to that of the reference signal (exciting signal) determine the shape of the bottom of the heap. Fig.1(c)(d) are the shapes of the heap’s bottom drawing according to the phase difference [note that the divisions of H axes are 10−4m/div in (c) and WCU 2003, Paris, september 7-10, 2003