Abstract:The impact of boundary layer suction on the aerodynamic performance of bowed compressor cascades is discussed in this paper. Preliminary studies are conducted in the context of a highly loaded compressor cascade with peak diffusion factor of 0.60 and camber angle of 60 degrees. Comparison between numerical simulation results and experiment data shows that blade bowing may well help to modify the radial migration of flow features and prevent the blade suction surface boundary layer from separating. It is noteworthy that there exists an optimum blade bowing design with different operating conditions to increase the incidence range and reduce the loss over the incidence range. With the introduction of the boundary layer suction, the blade design becomes more complicated. This paper, therefore, conducts a thorough numerical study on design parameters including bowed blade geometry, aspirated flow fraction, and aspiration slot location based on mechanical simplicity and fabrication constraints. For a better understanding of the flow physics, the aspiration slot and plenum are included as part of the computational domain. The aspirated fluid passes into the plenum and is removed through both the hub and the shroud of the blade. From there it can be dumped overboard or carried to another point in the engine to be used as cooling air. Without considering the stagnation pressure loss of the aspirated flow, the blade lose can be sustainably decreased with the growing aspirated flow fractions from 0.5% to 2.5% of the inlet mass flow. However, when the aspirated flow's effect on stagnation pressure loss is properly quantified, the blade's loss decreasing trend will be relatively stable or even reversed with the aspirated flow fraction increasing. The calculations show that the application of aspiration on the flow path needs to be investigated and combined with blade bowing to partly counter the negative impacts with the application of aspiration. The application of blade bowing on aspirated blade makes it possible to achieve the same loss reduction by using lower amounts of aspirated flow. In other words, the increase in spanwise pressure gradient near the endwalls can be further utilized to reduce the effects of secondary flow by bowed blade with the same aspirated flow fraction. Aspiration should not be isolated from blade bowing, the optimum blade bowing angle is different on the basis of different aspirated flow fraction and aspiration slot location. The aspiration slot location is determined by the flow phenomena such as the three-dimensional separation in the cascade corner. In consideration of the stagnation pressure loss from the aspirated flow, aspiration inside of the three-dimensional separation region has a beneficial impact on the blade loss. Conversely, it will quickly lose its effectiveness, or even lead to slight deterioration of the aerodynamic performance if aspiration location is in the midspan, outside the three-dimensional separation region.

The synergistic effect between compound lean and aspiration on aerodynamic performance in compressor cascades

Gpps-2017-0015 influence of endwall aspiration on aerodynamic performance in compound lean compressor cascades

The effect of aspiration configuration on aerodynamic performance in compound lean compressor cascades of gas turbines

Performance Sensitivity Analysis and Aerodynamic Optimization of Compressor Cascades by a Turbulence Adjoint Method

INFLUENCE OF TAILORED BOUNDARY LAYER SUCTION ON AERODYNAMIC PERFORMANCE IN BOWED COMPRESSOR CASCADES

Effect of Compound Lean Blades on Separation Structures in High Loaded Compressor Cascades under High Subsonic Condition

Effect Of Blade Aspiration Slot Configuration On The Aerodynamic Performance Of A Highly Loaded Aspirated Compressor Cascade

A Numerical Investigation of Boundary Layer Suction in Compound Lean Compressor Cascades

Influence of Blade Lean Together with Blade Clocking on the Overall Aerodynamic Performance of a Multi-Stage Turbine

Enhancing Aerodynamic Performances of a High-Turning Compressor Cascade Via Boundary Layer Suction

A Combination Application of Tandem Blade and Endwall Boundary Layer Suction in a Highly Loaded Aspirated Compressor Outlet Vane

Aerodynamic Optimization and Mechanism Investigation on Performance Improvements in a Transonic Compressor Cascade

Optimization Design of Variable Fillet for Different Boundary Thicknesses in a Highly Loaded Compressor Cascade

Numerical investigation of boundary layer suction on certain highly loaded aspirated compressor at low speeds

Numerical Investigations on Effects of Inlet Boundary Layer Characteristics on Aspirated Compressor Cascade

EXPLORING THE AERODYNAMIC FEASIBILITY OF SUBSTITUTING ASPIRATED CASCADE FOR TANDEM CASCADE

Effect of Combination of Active and Passive Flow Control Methods on the Flow Structures and Loss of a Highly-loaded Compressor Cascade

Effects of Boundary Layer Suction on Aerodynamic Performance in a High-load Compressor Cascade

Effects of Boundary Layer Suction on the Performances of Compressor Cascades

Influence of Aspiration Slot Shape on the Loss and Flow Structures of an Aspiration Compressor Cascade

Numerical Investigations on Separation in Highly-loaded Aspirated Compressor Cascade at Positive Incidences